Painiting My LSx

[mooseknuckles]

I like the painted intake.

[jtp67-72]

epoxy primer....satin nickel base clear with flattener....ls6 intake will be painted also....bling for accessories .......jim

[osaltyone]

So the paint you guys are using... is it made for heat or does it not matter.

[swb85]

I used Duplicolor engine paint on mine, has held up great over the last 3 years. Chevy orange/red on the block & valvecovers and ceramic silver on the intake, waterpump & accessories.

[JNJchev77]

Originally Posted by osaltyone

So the paint you guys are using... is it made for heat or does it not matter.

I would use some form of "High Heat" paint. Whether in a can or a little higher end paint (POR 15, Motor Coater, etc). As long as your cleaning process/prep is good, they will last.

[osaltyone]

Thanks! was just wondering. I don't see than many options when I go look for high heat paint so I was not sure.

[JNJchev77]

This link will give you some options, very good stuff...

http://www.kbs-coatings.com/motor-coater.html

[themb2g]

Originally Posted by swb85

I used Duplicolor engine paint on mine, has held up great over the last 3 years. Chevy orange/red on the block & valvecovers and ceramic silver on the intake, waterpump & accessories.

How well does the paint hold up on those F.A.S.T rails? I have the LSXRT with red anodized rails, and the red anodizing does not match a damn thing in my engine bay.

[swb85]

Originally Posted by themb2g

How well does the paint hold up on those F.A.S.T rails? I have the LSXRT with red anodized rails, and the red anodizing does not match a damn thing in my engine bay.

Those rails are actually from Speed Inc and are clear anodized aluminum, not painted. You can remove the red anodizing from your rails with oven cleaner, then polish the aluminum to a nice finish. Be careful with the oven cleaner as it can start eating into aluminum if left on too long.

[themb2g]

Here is mine painted up but not completely finished

[gringoloco]

Nice accessory drive! What compressor does it use?
Posted via Mobile Device

[themb2g]

its the Vintage air accessory kit and comes with the compressor.

[Kainedogg]

5.3 with LS6 intake and C5 FEAD
top is Hemi orange, pan is Chevy Orange and block is plain gloss black, all paints were rated for 500 degrees but I used a 1200 degree clear coat after.

[JNJchev77]

Here's mine. Cleaned, cleaned, and cleaned. etching primer and shot it with fire red moater coater from KBS Coatings. Love the stuff!!

[jsbgump]

Mine

[effects66]

Here is mine. Just finished painting. Now final assembly.

• LQ9
• L92 Heads
• New stiffer Comp Springs
• New Comp Cam XR281HR
• GM Carb intake
• Atomic EFI to look like old fashion carb
  

[68GMCCustom]

I think you'll be the 1st here with the atomic efi
Posted via Mobile Device

[effects66]

Yeah, I like a lot of things about it. I know there is mixed reviews on it, but it completes the look I am going for. My interpretation of a NASCAR, racing type of look. Well see how it comes out and how it the Atomic will perform.

Have you gotten to drive your truck yet? Was wondering how the new tranny is working for you.

[68GMCCustom]

Not yet...had a dbw pedal problem. Got a new pedal today and all is well, codes seem to be clear. I hope to get some miles in tomorrow...if I'm lucky maybe even a pass or two! I'll try and remember the gopro!
Posted via Mobile Device

[68Stepbed]

effects66, what kind of valve covers are those? They look good!

[effects66]

Sorry for the late response 68stepbed, the valve covers are from Katech. Great product. A little pricey but nice none the less.