MI Wanted - LWB Big Block C10 Drive shaft - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**DaHos** · 12-08-2012, 11:10 AM

I am looking for a complete 2 pc drive shaft for a LWB c10 1/2 ton with Big Block, TH400 and 12 bolt coil rear. Must be complete with HD style carrier bearing and cross member mount. THX ! D'

lynnfield · 12-08-2012, 12:16 PM

I have this one, LWB, heavy duty carrier, th400 to a Dana 60. Comes from a GMC 3/4 ton. Greg

**DaHos** · 12-18-2012, 08:26 AM

Ttt

JimKshortstep4x4 · 12-18-2012, 10:05 AM

I have one and will get a pic posted today. I believe that the TH 400 yoke is the smaller outside diameter like the 69's with TH 400 had.

Jim

JimKshortstep4x4 · 12-18-2012, 08:26 PM

My carrier mount is like the one pictured so probably not what you are looking for.

Jim

**DaHos** · 12-18-2012, 08:49 PM

Thanks Jim, Lynnfields looks like what I need, TH400 yoke (Larger dia. than the 350 yoke), HD carrier correct mount but I am unsure of the rear shaft length and joint style being from a 3/4T Dana 60 leaf truck.

Any more info on yours.

I know there is a BB, 400, long 2pc, 12 bolt, coil driveshaft, so I was hoping to find one and NOT build one.

Any help on this would be great. (even some measurements so I know what to look for)

JimKshortstep4x4 · 12-19-2012, 11:18 AM

It will b a couple of days before I can get some measurements as the shaft is stored so that I need help getting it down!

There are two yokes for the TH 400 trucks. One has a smaller od but the splines are the same. I thought the smaller one might be on some of the trucks possibly up to 72.

Jim

cheyenne402 · 12-19-2012, 09:23 PM

Dave, I have one with crossmember and Turbo 400. I wasn't planning on parting with it, but for right now my truck is staying original with 3 on tree and 402 big block.

PM me if your interested.

cheyenne402 · 03-27-2013, 01:25 PM

Still have driveshaft, crossmember and Turbo 400

$400 firm

burb71 · 03-27-2013, 05:54 PM

I have that same set up as lynnfield on my all original 68 C/10 with big block & turbo 400

**DaHos** · 03-27-2013, 05:58 PM

Quote:

Originally Posted by burb71

I have that same set up as lynnfield on my all original 68 C/10 with big block & turbo 400

12 bolt, eaton or Dana rear?

TripleNickel · 03-27-2013, 08:14 PM

Quote:

Originally Posted by cheyenne402

Still have driveshaft, crossmember and Turbo 400

$400 firm

Which rear end was in the donor truck?
What is the transmission's condition?
Where in Michigan are you located?

Thanks,

Wayne

cheyenne402 · 03-27-2013, 11:36 PM

Quote:

Originally Posted by TripleNickel

Which rear end was in the donor truck?
What is the transmission's condition?
Where in Michigan are you located?

Thanks,

Wayne

Not sure on rear end, tranny has been sitting quite awhile and will need rebuild.

Located in 48867
Posted via Mobile Device

**Cash3481** · 03-27-2013, 11:44 PM

DAHOS,
I will check and see if I have the coil spring BB 1/2 ton DS from the Sierra I parted is still out there. I think its out there but I am almost positive the 2 piece shaft has a different carrier bering support. Ill get you a pic if its out there in the AM when I get off work.
Mike

burb71 · 03-28-2013, 11:12 AM

12 bolt, 3:08 positrac

**Cash3481** · 03-28-2013, 03:46 PM

Dahos:
The two on the right and the one on the left were on bb trucks I parted. If they will work let me know. I didn't mark them all so I can't be for sure on fitment.
Mike
Posted via Mobile Device

cheyenne402 · 03-29-2013, 06:14 PM

Quote:

Originally Posted by TripleNickel

Which rear end was in the donor truck?
What is the transmission's condition?
Where in Michigan are you located?

Thanks,

Wayne

1/2 ton coil spring rear

12-08-2012, 11:10 AM	#1
DaHos Senior Member Join Date: Sep 2011 Location: Owosso, Michigan Posts: 2,862	Wanted - LWB Big Block C10 Drive shaft I am looking for a complete 2 pc drive shaft for a LWB c10 1/2 ton with Big Block, TH400 and 12 bolt coil rear. Must be complete with HD style carrier bearing and cross member mount. THX ! D' __________________ 1967 C10 SWB Owner - Rustbelt Restorations Last edited by DaHos; 12-08-2012 at 09:37 PM.

12-08-2012, 12:16 PM	#2
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: Wanted - LWB Big Block C10 Drive shaft I have this one, LWB, heavy duty carrier, th400 to a Dana 60. Comes from a GMC 3/4 ton. Greg Attached Images

12-18-2012, 08:26 AM	#3
DaHos Senior Member Join Date: Sep 2011 Location: Owosso, Michigan Posts: 2,862	Re: Wanted - LWB Big Block C10 Drive shaft Ttt __________________ 1967 C10 SWB Owner - Rustbelt Restorations

12-18-2012, 10:05 AM	#4
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Re: Wanted - LWB Big Block C10 Drive shaft I have one and will get a pic posted today. I believe that the TH 400 yoke is the smaller outside diameter like the 69's with TH 400 had. Jim __________________ 1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC

12-18-2012, 08:26 PM	#5
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Re: Wanted - LWB Big Block C10 Drive shaft My carrier mount is like the one pictured so probably not what you are looking for. Jim Attached Images __________________ 1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC

12-18-2012, 08:49 PM	#6
DaHos Senior Member Join Date: Sep 2011 Location: Owosso, Michigan Posts: 2,862	Re: Wanted - LWB Big Block C10 Drive shaft Thanks Jim, Lynnfields looks like what I need, TH400 yoke (Larger dia. than the 350 yoke), HD carrier correct mount but I am unsure of the rear shaft length and joint style being from a 3/4T Dana 60 leaf truck. Any more info on yours. I know there is a BB, 400, long 2pc, 12 bolt, coil driveshaft, so I was hoping to find one and NOT build one. Any help on this would be great. (even some measurements so I know what to look for) __________________ 1967 C10 SWB Owner - Rustbelt Restorations

12-19-2012, 11:18 AM	#7
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Re: Wanted - LWB Big Block C10 Drive shaft It will b a couple of days before I can get some measurements as the shaft is stored so that I need help getting it down! There are two yokes for the TH 400 trucks. One has a smaller od but the splines are the same. I thought the smaller one might be on some of the trucks possibly up to 72. Jim __________________ 1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC

12-19-2012, 09:23 PM	#8
cheyenne402 Registered User Join Date: Jul 2005 Location: Owosso, Michigan Posts: 783	Re: Wanted - LWB Big Block C10 Drive shaft Dave, I have one with crossmember and Turbo 400. I wasn't planning on parting with it, but for right now my truck is staying original with 3 on tree and 402 big block. PM me if your interested.

03-27-2013, 01:25 PM	#9
cheyenne402 Registered User Join Date: Jul 2005 Location: Owosso, Michigan Posts: 783	Re: Wanted - LWB Big Block C10 Drive shaft Still have driveshaft, crossmember and Turbo 400 $400 firm

03-27-2013, 05:54 PM	#10
burb71 Active Member Join Date: Oct 2002 Location: Ft. Myers, Fl Posts: 1,716	Re: Wanted - LWB Big Block C10 Drive shaft I have that same set up as lynnfield on my all original 68 C/10 with big block & turbo 400

03-27-2013, 11:44 PM	#14
Cash3481 Loves all GMC trucks Join Date: Jul 2010 Location: Columbia Mo Posts: 4,435	Re: Wanted - LWB Big Block C10 Drive shaft DAHOS, I will check and see if I have the coil spring BB 1/2 ton DS from the Sierra I parted is still out there. I think its out there but I am almost positive the 2 piece shaft has a different carrier bering support. Ill get you a pic if its out there in the AM when I get off work. Mike

03-28-2013, 11:12 AM	#15
burb71 Active Member Join Date: Oct 2002 Location: Ft. Myers, Fl Posts: 1,716	Re: Wanted - LWB Big Block C10 Drive shaft 12 bolt, 3:08 positrac

03-28-2013, 03:46 PM	#16
Cash3481 Loves all GMC trucks Join Date: Jul 2010 Location: Columbia Mo Posts: 4,435	Re: Wanted - LWB Big Block C10 Drive shaft Dahos: The two on the right and the one on the left were on bb trucks I parted. If they will work let me know. I didn't mark them all so I can't be for sure on fitment. Mike Posted via Mobile Device Attached Images



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.