|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-16-2013, 10:14 AM
|
#1 |
|
Registered User
Join Date: Jan 2013
Location: Leonardtown, MD
Posts: 1,651
|
valve cover dent repair
A couple months ago a buddy of mine came over with a bumper filler panel off a 61 Starliner he's putting together as a 70th b-day present for his dad. He was using my media blast cabinet to clean off the paint and was planning on spraying some Krylon and reinstalling. Well, I had him strip the paint, I smoothed out some dings with the hammer and dolly, and here's how I finished it, using some of my Imron rather than his Krylon...
Well I stopped by to check it out after he installed it, and noticed the valve covers looked like someone had changed out the intake and dropped it a few times on the valve covers. So he dropped them off for some dent repair this evening...     All of these tools were used this evening at one point or another...   Dents were worked with various implements of destruction, filed to find the high spots, and low spots bumped up, then repeat.   As they will be painted, we'll leave off with the following.... Sandblasting and some H/K epoxy primer will take care of any remaining defects...      
__________________
Robert |
|
|
|
02-16-2013, 10:17 AM
|
#2 |
|
Registered User
Join Date: Jan 2013
Location: Leonardtown, MD
Posts: 1,651
|
Re: valve cover dent repair
Here they are all hot tanked, sandblasted, and ready to go....
  Here's the official 2 x 8 valve cover paint fixtures...   A couple coats of H/K epoxy and a guide coat and couple days of cure time before wetsanding....   
__________________
Robert Last edited by MP&C; 02-16-2013 at 10:33 AM. |
|
|
|
|
02-16-2013, 10:35 AM
|
#3 |
|
Registered User
Join Date: Jan 2013
Location: Leonardtown, MD
Posts: 1,651
|
Re: valve cover dent repair
And here's where we are as of last night. There were a couple sand-throughs on the valve covers, so some epoxy was mixed and reduced 10% to use as a sealer....
  Here's the paint code for the early 60's Hi-po 390... Used acrylic enamel.  Finished up, looks quite a bit smoother than before....     No filler used, just wet sanding the epoxy primer.
__________________
Robert |
|
|
|
|
02-18-2013, 08:06 AM
|
#4 |
|
I dun gradjiated collij!!!
Join Date: Jan 2006
Location: St. Helens Oregon
Posts: 1,751
|
Re: valve cover dent repair
Absolutely beautiful work... metal manipulation is an art.
__________________
Built NOT Bought. Viper Red 1971 LWB C10 355 Vortec W/700R4 4/5 drop AKA Screamin' You are missed!
2006 F150 XLT 5.4L Triton Rollin' on 22s the "F1" 67 C20 PS/AC/327/TH400 we call 'er "Bessie" 67 Malibu PS/ZR1-LS1 Brakes/350 Vortec/700R4 2/2 drop on 18" 338s - Tracy's "Boo" Boosted '67 Cougar EFI 5.0 HO roller motor/T5/8.8 Tracloc/ 4 wheel disks - "Project Panther" 79 Honda Z50 - stretched, cafe'd and hotrodded 125CC Lifan/5spd FEAR THE MONKEY! |
|
|
|
|
02-21-2013, 10:54 PM
|
#5 |
|
Registered User
Join Date: Feb 2007
Location: Marana, Arizona
Posts: 3,459
|
Re: valve cover dent repair
Reminds me of my SBC cover. Except yours looks awesome!
And mine is well.....not. 
__________________
"I feel the need for speed!"... as soon as I am done with my nap. |
|
|
|
|
02-21-2013, 11:17 PM
|
#6 |
|
Registered User
Join Date: Jan 2013
Location: Leonardtown, MD
Posts: 1,651
|
Re: valve cover dent repair
That doesn't look like it would take too much to straighten it out..
__________________
Robert |
|
|
|
|
03-21-2013, 09:34 AM
|
#7 |
|
Registered User
Join Date: Jan 2013
Location: Leonardtown, MD
Posts: 1,651
|
Re: valve cover dent repair
As a follow up to the valve cover repairs, the owner has the car just about ready, just needs some tune up work...
   
__________________
Robert |
|
|
|
|
03-21-2013, 09:44 AM
|
#8 |
|
C/10 junkie
Join Date: Nov 2010
Location: Stockton Ca
Posts: 9,094
|
Re: valve cover dent repair
Very nice job!!
__________________
Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!" 
|
|
|
|
|
03-21-2013, 11:35 AM
|
#9 |
|
Registered User
 
Join Date: Sep 2010
Location: Formerly MD and San Diego, now loving life in Arizona
Posts: 1,636
|
Re: valve cover dent repair
Beautiful work and a very nice looking car. I bet that thing moves well!
__________________
Alan 2012 Ram 3500 Dually Crew Cab 6.7 Cummins 2014 Palomino Columbus 340RK 5th wheel '69 Chevy C10 396BB |
|
|
|
|
03-21-2013, 03:15 PM
|
#10 |
|
Registered User
Join Date: Aug 2010
Location: Des Moines, IA
Posts: 1,241
|
Re: valve cover dent repair
Looks great. I have a set of the script chevrolet valve covers shown earlier in this thread that have some dents that I will be smoothing out.
__________________
Bud |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
