6 volt ignition switch question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

c10 custom · 12-08-2013, 11:28 PM

Hi guys i have a 1947 gmc truck second series looks like a 48
anyways i was wondering can i leave the original ignition switch when
changing to 12 volt system i am going to install a distributor from a 1981 chev truck with HEI 6 cylinder engine any advice would be great thank you everybody

OrrieG · 12-09-2013, 01:19 AM

I think the ing switch will be ok, but go over to the stovebolts.com tech section and look at the electrical 12v conversion thread. It tells in detail what will and will not be affected.

_Ogre · 12-09-2013, 02:40 PM

like orrieg mention the switch will work, you have less amperage on 12v vs 6v for a given load
you will need to add a push button for the starter if you choose to keep your old switch
not sure if your switch has an acc position either.

**mr48chev** · 12-09-2013, 04:50 PM

As Ogre said you will need to add a push button for the starter but the switch will handle the ignition ok if it is in good shape.

If you are worried about the switch handling the draw from the HEI install a relay for the HEI that is activated by the ignition switch. That would solve the load problem and be a real easy hookup.

c10 custom · 12-11-2013, 10:20 AM

how is the relay wiring supposed to look hooked up do you have a wiring diagram for this

OrrieG · 12-11-2013, 04:09 PM

On a boush type relay 12v power goes to pin 30. pin 86 grounds. pin 87 goes to HEI power. pin 85 come from ignition "on" wire that would normally go to the coil or resistor. So when you turn the key to ON it closed the relay connection allowing full power to flow from pin 30 thru the relay out pin 87 to the HEI. Mount the relay as close to the HEI as possible on the firewall side.

HEIs need full 12v power not shared with anything else. If it comes directly from the battery or alt connection use a 12 GA wire with 16GA fusible link. The ing switch to relay wire can be 16 GA.

Zach B · 12-13-2013, 11:43 AM

Actually on my grandfathers 55 first he converted it to a 12 volt system and changed the switch. However he left the starter as a 6 volt. The truck actually starts a little faster this way. You have to be carful though because it's easy to burn up a starter.

12-08-2013, 11:28 PM	#1
c10 custom Registered User Join Date: Aug 2011 Location: Lethbridge Montana Posts: 259	6 volt ignition switch question Hi guys i have a 1947 gmc truck second series looks like a 48 anyways i was wondering can i leave the original ignition switch when changing to 12 volt system i am going to install a distributor from a 1981 chev truck with HEI 6 cylinder engine any advice would be great thank you everybody

12-09-2013, 01:19 AM	#2
OrrieG Registered User Join Date: Jun 2006 Location: Idaho Posts: 8,800	Re: 6 volt ignition switch question I think the ing switch will be ok, but go over to the stovebolts.com tech section and look at the electrical 12v conversion thread. It tells in detail what will and will not be affected. __________________ 1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project

12-09-2013, 02:40 PM	#3
_Ogre Registered User Join Date: Jan 2012 Location: Motown Posts: 7,680	Re: 6 volt ignition switch question like orrieg mention the switch will work, you have less amperage on 12v vs 6v for a given load you will need to add a push button for the starter if you choose to keep your old switch not sure if your switch has an acc position either. __________________ cool, an ogre smiley Ogre's 58 Truk build how to put your truck year and build thread into your signature shop air compressor timer

12-09-2013, 04:50 PM	#4
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,711	Re: 6 volt ignition switch question As Ogre said you will need to add a push button for the starter but the switch will handle the ignition ok if it is in good shape. If you are worried about the switch handling the draw from the HEI install a relay for the HEI that is activated by the ignition switch. That would solve the load problem and be a real easy hookup. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

12-11-2013, 10:20 AM	#5
c10 custom Registered User Join Date: Aug 2011 Location: Lethbridge Montana Posts: 259	Re: 6 volt ignition switch question how is the relay wiring supposed to look hooked up do you have a wiring diagram for this

12-11-2013, 04:09 PM	#6
OrrieG Registered User Join Date: Jun 2006 Location: Idaho Posts: 8,800	Re: 6 volt ignition switch question On a boush type relay 12v power goes to pin 30. pin 86 grounds. pin 87 goes to HEI power. pin 85 come from ignition "on" wire that would normally go to the coil or resistor. So when you turn the key to ON it closed the relay connection allowing full power to flow from pin 30 thru the relay out pin 87 to the HEI. Mount the relay as close to the HEI as possible on the firewall side. HEIs need full 12v power not shared with anything else. If it comes directly from the battery or alt connection use a 12 GA wire with 16GA fusible link. The ing switch to relay wire can be 16 GA. __________________ 1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project

12-13-2013, 11:43 AM	#7
Zach B Registered User Join Date: Jun 2013 Location: El Dorado Springs Missouri Posts: 246	Re: 6 volt ignition switch question Actually on my grandfathers 55 first he converted it to a 12 volt system and changed the switch. However he left the starter as a 6 volt. The truck actually starts a little faster this way. You have to be carful though because it's easy to burn up a starter.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.