|
05-12-2014, 09:23 PM
|
#1 |
|
Registered User
Join Date: Apr 2013
Location: New York
Posts: 24
|
Pulling an sm465
Can someone give me a detailed step by step on how to pull an sm465/205 out of a k10? Thanks!
|
|
|
|
05-13-2014, 08:46 PM
|
#2 |
|
Registered User
Join Date: Feb 2012
Location: Big Valley. Alberta
Posts: 674
|
Re: Pulling an sm465
Probably missing a few things,but here goes: First thing is get hold of a good transmission/transfer case jack.I bought a cheaper one probably close to twenty years ago & it still works good,had a threaded rod instead of a hydraulic cylinder.Drain your T case,disconnect driveshaft,speedo,shift linkage on t case.Support the transmission/transfer case(some might not agree,but this always works for me) by using a square piece of metal or plywood approx 6" square under the oilpan & a bottle jack under it.Using the tranny jack,place under the t case & unbolt it from adapter.Make sure it's supported well. When I was a lot younger I bench pressed the 205 out,but I got wiser as I grew older! Once t case is out.Remove the crossmember,place jack under tranny,remove the trim around gear shift lever & remove the stick.Push down on the retainer & turn 90 degrees. Usually I unbolt the 4 1/2" bolts on tranny to bell housing & pull it that way,after it's out,then drop your engine down some & undo the bell housing to engine bolts if you need to take that much apart.If your going to leave it any length of time,support the engine better & don't rely only on the bottle jack. Oh,forgot too,you have to drop the front driveshaft from t case as well.
__________________
1977 Chev C30 454/465/14ff DRW 1974 Chev C20.350/465/14ff " Rock n Roll ain't noise pollution" 
|
|
|
|
|
09-06-2014, 07:38 PM
|
#3 |
|
Registered User
Join Date: Mar 2013
Location: Washington
Posts: 238
|
Re: Pulling an sm465
Wish I would of seen this ahead of time lol, guess I need to follow these steps instead of trying to remove the T-case & transmission as 1 big part.
__________________
RoughKuntry 73 GMC 25 HUNDRED :Sold 79 GMC High Sierra 4x4 (Ma-Duece) :Sold 99 Chevrolet LS 4.8l/5 Speed Manual 4x4 :Selling 88 Chevrolet Burban 2500 4x4 :Buying 
|
|
|
|
|
09-07-2014, 12:23 AM
|
#4 | |
|
Registered User
Join Date: Feb 2012
Location: Big Valley. Alberta
Posts: 674
|
Re: Pulling an sm465
Quote:
__________________
1977 Chev C30 454/465/14ff DRW 1974 Chev C20.350/465/14ff " Rock n Roll ain't noise pollution"
|
|
|
|
|
|
09-07-2014, 09:12 AM
|
#5 |
|
Registered User
Join Date: Mar 2012
Location: edgartown mass
Posts: 852
|
Re: Pulling an sm465
i have done it both ways if you are alone spite the case and trans. only thing i say diff then what was said is i used a jack stand under the motor and some 2x4 behind the heads to keep it from ripping the rubbers
__________________
1986 c20 "the hillbilly" 350 sm465 3.42gears 21mpg at 70mph 1985 k30 "the ice cream truck from hell" no rust az truck 197-8??? c30 "ramp truck" 454 1978 monte carlo 350 350th with 2.73 gears. no rust. sc car |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
