3/4 ton running board splash apron mount - The 1947 - Present Chevrolet & GMC Truck Message Board Network

coralhead · 03-31-2012, 11:10 AM

Can someone show how the rear top corner of the splash apron is mounted? There is a hole in the rolled over section that I had to repair since it was torn out. I am sure that there is some sort of bracket mount that I may be missing. Any help?

coralhead · 03-31-2012, 03:17 PM

This is the end I am interested in.

coralhead · 11-01-2012, 06:42 AM

Bump

jake1ekaj · 06-27-2014, 12:20 PM

I have the same question and have been looking for photos of these attachment points. Its been like 26 years since I tore this thing apart. Enlisted & retired from the Air Force. Then went to college for four years. While in the AF, dad started working on it when he retired from his job. Mom is fixin to "put a stick of dynamite under it" if it doesn't get out of the garage. One of the last things are the side filler panels. I get that they bolt to the top of the running boards, but what about the top corners. I think the tab in the back attaches to the inner fender flange. Does the front attach to this bracket?

The tab sticking off in the bottom corner in the photo, that mounts to the fender flange?

I would appreciate it if one of y'all would take a photo of the upper mounting points on a stock truck. (mom would appreciated it too)

Thanks in advance.
Jake

dwcsr · 06-27-2014, 10:39 PM

The apron bolts to the top of the running board. the bracket bolts as pictured

dwcsr · 06-28-2014, 02:23 PM

correction to the picture. I had it up side down

**oldman3** · 06-28-2014, 03:34 PM

I believe the apron on the right is what yours should look like installed, hope this helps...Jim

**mr48chev** · 06-28-2014, 11:25 PM

Here is one I have.

More photos of the filler here
http://s173.photobucket.com/user/mr4...?sort=4&page=1

**mr48chev** · 06-28-2014, 11:49 PM

I went back out and looked again and mine has an L bracket that is welded to the filler panel and it is bolted though the hole in the bracket.

I can't believe I paid real money for that rusty mess.

coralhead · 06-29-2014, 07:50 AM

I believe the other poster is interested in the other end where the splash apron is attached to the rear fender. It is a offset tab welded to the top back of the apron and bolts to the fender.

jake1ekaj · 06-29-2014, 08:45 AM

Thanks for the replies and pictures. I think I'll try and get them on today. Dad bought fiberglass running boards and fenders for it years ago and none of those parts seem to fit right. Thanks y'all.

03-31-2012, 11:10 AM	#1
coralhead Registered User Join Date: Jun 2011 Location: Floyds Knobs, IN Posts: 430	3/4 ton running board splash apron mount Can someone show how the rear top corner of the splash apron is mounted? There is a hole in the rolled over section that I had to repair since it was torn out. I am sure that there is some sort of bracket mount that I may be missing. Any help?

03-31-2012, 03:17 PM	#2
coralhead Registered User Join Date: Jun 2011 Location: Floyds Knobs, IN Posts: 430	Re: 3/4 ton running board splash apron mount This is the end I am interested in.

11-01-2012, 06:42 AM	#3
coralhead Registered User Join Date: Jun 2011 Location: Floyds Knobs, IN Posts: 430	Re: 3/4 ton running board splash apron mount Bump

06-27-2014, 12:20 PM	#4
jake1ekaj Registered User Join Date: Jun 2014 Location: Cohocton, NY Posts: 2	Re: 3/4 ton running board splash apron mount I have the same question and have been looking for photos of these attachment points. Its been like 26 years since I tore this thing apart. Enlisted & retired from the Air Force. Then went to college for four years. While in the AF, dad started working on it when he retired from his job. Mom is fixin to "put a stick of dynamite under it" if it doesn't get out of the garage. One of the last things are the side filler panels. I get that they bolt to the top of the running boards, but what about the top corners. I think the tab in the back attaches to the inner fender flange. Does the front attach to this bracket? The tab sticking off in the bottom corner in the photo, that mounts to the fender flange? I would appreciate it if one of y'all would take a photo of the upper mounting points on a stock truck. (mom would appreciated it too) Thanks in advance. Jake

06-27-2014, 10:39 PM	#5
dwcsr Hollister Road Co. Join Date: Apr 2005 Location: Houston Posts: 6,131	Re: 3/4 ton running board splash apron mount The apron bolts to the top of the running board. the bracket bolts as pictured Attached Images

06-28-2014, 02:23 PM	#6
dwcsr Hollister Road Co. Join Date: Apr 2005 Location: Houston Posts: 6,131	Re: 3/4 ton running board splash apron mount correction to the picture. I had it up side down Attached Images

06-28-2014, 03:34 PM	#7
oldman3 Senior Member Join Date: Mar 2011 Location: West Plains, Missouri Posts: 7,559	Re: 3/4 ton running board splash apron mount I believe the apron on the right is what yours should look like installed, hope this helps...Jim Attached Images __________________ my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br />

06-28-2014, 11:25 PM	#8
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,711	Re: 3/4 ton running board splash apron mount Here is one I have. More photos of the filler here http://s173.photobucket.com/user/mr4...?sort=4&page=1 __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

06-28-2014, 11:49 PM	#9
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,711	Re: 3/4 ton running board splash apron mount I went back out and looked again and mine has an L bracket that is welded to the filler panel and it is bolted though the hole in the bracket. I can't believe I paid real money for that rusty mess. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

06-29-2014, 07:50 AM	#10
coralhead Registered User Join Date: Jun 2011 Location: Floyds Knobs, IN Posts: 430	Re: 3/4 ton running board splash apron mount I believe the other poster is interested in the other end where the splash apron is attached to the rear fender. It is a offset tab welded to the top back of the apron and bolts to the fender.

06-29-2014, 08:45 AM	#11
jake1ekaj Registered User Join Date: Jun 2014 Location: Cohocton, NY Posts: 2	Re: 3/4 ton running board splash apron mount Thanks for the replies and pictures. I think I'll try and get them on today. Dad bought fiberglass running boards and fenders for it years ago and none of those parts seem to fit right. Thanks y'all.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.