'62 GMC BurbMaster "Rust"oration, Patina Build..... - Page 18 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**ChiefRocka** · 01-22-2016, 10:34 PM

Removed floor skeleton ...

-
-

**ChiefRocka** · 01-22-2016, 10:56 PM

Now we are getting close to Real time ...

A couple of weeks ago, I got back on it.

My powder coater needed his Rotisserie back, so that kinda put a hurt on the process.

If I can say one thing good came out of my divorce, is the fact that my kids hang with momma every other week. So the weeks that I am "off", I can work late after hours to get more stuff done (Just for record, I rather have my kids 100% of the time, but unfortunately, it is what it is)

Some cold nights meant bring it inside ....
-
-

-
-

**ChiefRocka** · 01-22-2016, 11:04 PM

The Rotisserie came back about two weeks ago, so I began remounting the body to it.

This time I use spacers (old lugnuts) and longer bolts to allow the sand and then the powder to get behind the mounting points ....
-
-
But before I could mount it up, I needed to remove the rear beat up gate crossmember ... and rebrace to its location
-
-

-
-

**ChiefRocka** · 01-22-2016, 11:09 PM

-
-

-
-
-
Here is a couple of dork shots ......
-
-
-

-
-
-

-
-

-
-
-

**ChiefRocka** · 01-24-2016, 12:38 PM

Well ... My blaster all of sudden got a busy load to do, so it gave me a few days to finish up as much metal repair before powder.

The dash was custom modified back in the day with a hacksaw and hammer, so decided to repair that now....as well as some holes.

-
-

**ChiefRocka** · 01-24-2016, 01:04 PM

-
-
Looks like they didn't have drill bits passed 5/8", so looks like they use a punch to "get r done"...
-
-

-
-
I decided to cut this entire section out. Being the Burbmaster is not 100% OG, this will give me a clean slate for a nice headunit, Vin Air controls, etc.
-
-

-
-

**ChiefRocka** · 01-24-2016, 01:17 PM

This dash plate took me about 2 hours. Tack, cool, grind, cool, repeat ... MANY TIMES !
-
-

-
-

**ChiefRocka** · 01-24-2016, 01:51 PM

Moving on to A-pillar, and spotlight hole removal ....
-
-

-
-

**ChiefRocka** · 01-24-2016, 01:55 PM

-
-

**ChiefRocka** · 01-24-2016, 02:03 PM

I had my girl working on the floor from Burb1. She was busy drilling out all the spots.

This floor needs repair near the rockers, but still in better shape than the OG one in Burb2.

Burb2 had a rubber floormat installed since new, which kept the moisture on the floor....leading to rot.

-
-
-

-
-

**ChiefRocka** · 01-24-2016, 02:40 PM

Thanks to "Perro13", I picked up a clean hood, and a nice set of fenders.

These fenders like to rust, and from these pics you will see why....
-
-

-
-

-
-
Lower mount is in good shape, but full of dirt. I holed sawed clean out holes
-
-

-
-

**ChiefRocka** · 01-24-2016, 02:45 PM

A few Misc Pics ....
-
-

-
-
-
-

-
-

**Advanced Design** · 01-24-2016, 04:08 PM

Nice repairs Chief. It is amazing how modifications were hacked back in the day.

Lotta floor spot weld cutting there!

**ChiefRocka** · 01-24-2016, 06:32 PM

Quote:

Originally Posted by Advanced Design

Nice repairs Chief. It is amazing how modifications were hacked back in the day.

Lotta floor spot weld cutting there!

Thanks buddy ...

That's why she's doing it !!

65sub · 01-24-2016, 10:08 PM

Nice progress Chief. Your interior repairs look good.

jonzcustomshop · 01-24-2016, 11:14 PM

wow! taking it down to the bones!
is that rear tail panel just bolted in? is it welded anywhere?

both of my subs need a little rust repair in that area, and if it just unbolts... that would make for some easy repair...

**ChiefRocka** · 01-24-2016, 11:57 PM

Quote:

Originally Posted by jonzcustomshop

wow! taking it down to the bones!
is that rear tail panel just bolted in? is it welded anywhere?

both of my subs need a little rust repair in that area, and if it just unbolts... that would make for some easy repair...

YOU ARE SO LUCKY YOU ASKED ME THAT !!

It does !!

But I found out the hard way !!

I had my buddy Joe start to drill out spots on the rear tail panel of Burb 1.

After about half way through, we realized ... IT JUST UNFOLDED !!

Ugh !!!!

Pics to follow ....

likaroc13 · 01-25-2016, 03:12 AM

Keep rockin', John! It looks like a ton of work, but I know a guy like yourself can handle it. It'll be sweet when you're done.

moregrip · 07-01-2016, 10:05 PM

Awesome build brother! Subscribed!

gulfcoast66 · 01-27-2017, 12:19 AM

Quote:

Originally Posted by moregrip

Awesome build brother! Subscribed!

X2.. How's the Burb Master coming along Chief ??

**ChiefRocka** · 02-07-2017, 10:06 AM

Is coming along .... slowly but surely.

I have many pics to update, but no time.

My shop has me busy !

jturner18 · 04-17-2017, 07:56 PM

Where's it at? 11 years later.

**ChiefRocka** · 04-18-2017, 05:18 PM

Quote:

Originally Posted by jturner18

Where's it at? 11 years later.

Wow ... has it been that long already ??

**ChiefRocka** · 04-18-2017, 05:19 PM

Quote:

Originally Posted by ChiefRocka

Wow ... has it been that long already ??

It's coming really soon ..... SEMA 2025

pimpston65 · 08-07-2017, 09:24 PM

i stole your design Chief!!!

01-22-2016, 10:34 PM	#426
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... Removed floor skeleton ... - - - - - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-22-2016, 10:56 PM	#427
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... Now we are getting close to Real time ... A couple of weeks ago, I got back on it. My powder coater needed his Rotisserie back, so that kinda put a hurt on the process. If I can say one thing good came out of my divorce, is the fact that my kids hang with momma every other week. So the weeks that I am "off", I can work late after hours to get more stuff done (Just for record, I rather have my kids 100% of the time, but unfortunately, it is what it is) Some cold nights meant bring it inside .... - - - - - - - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-22-2016, 11:04 PM	#428
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... The Rotisserie came back about two weeks ago, so I began remounting the body to it. This time I use spacers (old lugnuts) and longer bolts to allow the sand and then the powder to get behind the mounting points .... - - But before I could mount it up, I needed to remove the rear beat up gate crossmember ... and rebrace to its location - - - - - - - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-22-2016, 11:09 PM	#429
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... - - - - - Here is a couple of dork shots ...... - - - - - - - - - - - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-24-2016, 12:38 PM	#430
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... Well ... My blaster all of sudden got a busy load to do, so it gave me a few days to finish up as much metal repair before powder. The dash was custom modified back in the day with a hacksaw and hammer, so decided to repair that now....as well as some holes. - - - - - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-24-2016, 01:04 PM	#431
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... - - Looks like they didn't have drill bits passed 5/8", so looks like they use a punch to "get r done"... - - - - I decided to cut this entire section out. Being the Burbmaster is not 100% OG, this will give me a clean slate for a nice headunit, Vin Air controls, etc. - - - - - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-24-2016, 01:17 PM	#432
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... This dash plate took me about 2 hours. Tack, cool, grind, cool, repeat ... MANY TIMES ! - - - - - - - - - - - - - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-24-2016, 01:51 PM	#433
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... Moving on to A-pillar, and spotlight hole removal .... - - - - - - - - - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-24-2016, 01:55 PM	#434
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... - - - - - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-24-2016, 02:03 PM	#435
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... I had my girl working on the floor from Burb1. She was busy drilling out all the spots. This floor needs repair near the rockers, but still in better shape than the OG one in Burb2. Burb2 had a rubber floormat installed since new, which kept the moisture on the floor....leading to rot. - - - - - - - - - - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-24-2016, 02:40 PM	#436
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... Thanks to "Perro13", I picked up a clean hood, and a nice set of fenders. These fenders like to rust, and from these pics you will see why.... - - - - - - - - - - Lower mount is in good shape, but full of dirt. I holed sawed clean out holes - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-24-2016, 02:45 PM	#437
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... A few Misc Pics .... - - - - - - - - - - - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

01-24-2016, 04:08 PM	#438
Advanced Design Senior Member Join Date: Jul 2012 Location: Oblong, Illinois Posts: 7,028	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... Nice repairs Chief. It is amazing how modifications were hacked back in the day. Lotta floor spot weld cutting there! __________________ Doug Advanced Design’s 1977 Blazer Build Advanced Design's '48 'Burb Build Mrs Advanced Design's '72 Suburban Advanced Design's 56 BelAir LS swap

01-24-2016, 10:08 PM	#440
65sub Registered User Join Date: Jun 2014 Location: dresden , ontario Posts: 628	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... Nice progress Chief. Your interior repairs look good. __________________ Dale ---------------- My suburban's Twisted Little Sister http://67-72chevytrucks.com/vboard/s...d.php?t=655167

01-24-2016, 11:14 PM	#441
jonzcustomshop 1961 crewcab Join Date: Dec 2007 Location: missoula, mt Posts: 6,164	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... wow! taking it down to the bones! is that rear tail panel just bolted in? is it welded anywhere? both of my subs need a little rust repair in that area, and if it just unbolts... that would make for some easy repair... __________________ 60 build: http://67-72chevytrucks.com/vboard/s...d.php?t=280904 61 crew build: http://67-72chevytrucks.com/vboard/s...d.php?t=646830 63 build: http://67-72chevytrucks.com/vboard/s...d.php?t=336537 64 'burb build: http://67-72chevytrucks.com/vboard/s...d.php?t=448681 65 'burb build: http://67-72chevytrucks.com/vboard/s...d.php?t=590715 65 build: http://67-72chevytrucks.com/vboard/s...d.php?t=281955



Register or Log In To remove these advertisements.

01-25-2016, 03:12 AM	#443
likaroc13 Rollin' Old Skool Join Date: Jun 2007 Location: Hattiesburg, MS Posts: 5,371	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... Keep rockin', John! It looks like a ton of work, but I know a guy like yourself can handle it. It'll be sweet when you're done. __________________ _____________________________________________ Phillip My Build threads: 1966 Chevy C-10 "Black Betty" shortbed, fleetside, BBW, 327 V8/ Powerglide (under construction) http://67-72chevytrucks.com/vboard/s...ighlight=betty 1997 Chevy Tahoe, 2dr/2wd, mild custom (Daily driver) http://67-72chevytrucks.com/vboard/s...d.php?t=601142 Pics: '66 C-10 https://flic.kr/s/aHsjHWD4h9 '97 Tahoe https://flic.kr/s/aHsjGZ7wKP '93 C-1500 https://flic.kr/s/aHskxdpdnQ '88 S-10 Blazer https://flic.kr/s/aHsjYGx4Md Previous Rides: 1993 Chevy S-10 ext. cab, 4.3L, 4/5 drop (Sold) 1993 Chevy C-1500 short/step Retro-Rod (Sold) 1988 S-10 Blazer 2dr/2wd mild custom (Sold)

07-01-2016, 10:05 PM	#444
moregrip Registered User Join Date: Dec 2008 Location: Las Vegas, NV Posts: 811	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... Awesome build brother! Subscribed! __________________ 1983 Chevy C10 250/3spd (current project truck) 1976 Chevy C10 350/350 Heavy Half (future project truck)

02-07-2017, 10:06 AM	#446
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... Is coming along .... slowly but surely. I have many pics to update, but no time. My shop has me busy ! __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

04-17-2017, 07:56 PM	#447
jturner18 Registered User Join Date: Nov 2015 Location: Trenton Ky Posts: 93	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... Where's it at? 11 years later.

08-07-2017, 09:24 PM	#450
pimpston65 Registered User Join Date: Aug 2013 Location: corktown,mi. Posts: 5,194	Re: '62 GMC BurbMaster "Rust"oration, Patina Build..... i stole your design Chief!!! Attached Images

Register or Log In To remove these advertisements.