CA FS: 1972 C-10 complete short bed project truck

[zamboni2354]

Hey guys,

Life is getting in the way and I don't think I'm going to get around to working on my project for a while. I spent a good amount of time gathering up some nice parts for my truck and I'm not excited at the idea of getting rid of it but hopefully it will go to someone that can finish it. I'm selling all for $5,000.00. I'm not interested in parting it out..unless you want to buy $5,000 worth of parts..lol

There's too much to photo. I'm in long beach. if you are interested let me know and we can talk and I can show you everything.

1972 cheyenne near rust free cab.
71 original shortbed frame.
the bed is pretty rough. i have some cuts from another bed for patching and a one new repo bedside that has some minor shipping damage.
buddy buckets that need restored, I have had the frame blasted and powdercoated.
350 engine with new hedman hedders, new sparkplug wires. ran great.
700r4 tranny that ran great. new bowtie overdrives kit for it.
373 posi rear end.
auto tilt steering.
I have two tach dashes and one regular
new american autowire harness.
a/c system with several cans of r12
new starter
new water pump
aluminum radiator
cpp brake booster
cpp drop spindles and springs. about 3 in the front and 5 in the rear.
POL tranny cross member
new rear trailing arm cross member
new exhaust (flowmaster)
also two new black widow mufflers that I won at the brothers truck show
am/am stock stereo and an am stock radio as well.

much more..come and check it out.

as it sits



some of the parts on it:

[JimKshortstep4x4]

I am sorry you have to give up on your project! Looks like a good deal for someone.

Good luck on your sale.

Jim

[zamboni2354]

Also includes close to 300 bucks worth of epoxy primer and 2k primer from SPI.

[zamboni2354]

Originally Posted by JimKshortstep4x4

I am sorry you have to give up on your project! Looks like a good deal for someone.

Good luck on your sale.

Jim

thanks Jim!

[zamboni2354]

Any interest? if you have an interest come by and see all the other parts that come with it and make an offer.

If someone wanted the frame with engine,trans, running gear, exhaust, bed and bare cab for say 3,300 I'd do that cause I could probably part out the rest to make up the difference.

[leddzepp]

I'd be interested in the rolling chassis, driveshaft, and exhaust (basically your second pic)

[68bowtie]

lots of good parts there. i'll apologize in advance for everyone calling dibs on individual parts. very tempting!!

[zamboni2354]

the motor is a chevy 350 but the motor mounts are the 1972 big block mounts...just in case you want to buy the truck and upgrade it later to a BB =)

very clean original steering wheel
deluxe door panels
used power window units for the doors.
and more.

[zamboni2354]

bump.

[396ci]

in the pic on the rack, looks like the driver side of frame is higher than pass side. is frame bent or tweaked at all?

[zamboni2354]

Originally Posted by 396ci

in the pic on the rack, looks like the driver side of frame is higher than pass side. is frame bent or tweaked at all?

there's no visible damage to the frame. the right side tire is low..well flat now. what would be the most accurate way to check it at home? I coudl add air to the tire until I measure from the ground to the axle the same measurement on both sides or just put the axle on blocks then measure the frame to the ground to confirm level..does that sound like it would be the best way?

[chevycc1970]

I know that you don't want to sell individual parts and I totally understand that I would be the same way. I wanted to see if you are interested in selling some of the R-12. Thank you

[cypressbog]

How much for the buddy buckets?

[PAPABEAR]

I know am going to be one of those guys but if you part out am interested in the trailing arms and the cross member.

[jr1000yarder]

Doors....tailgate...

[zamboni2354]

thought I would post some pic's of some of the stuff that comes with the truck if you buy it. sorry if you have a slow data connection..lol

two original dash pads and one repo





tilt column



new wiring harness


A/c firewall seals
grills for vents
auto shift linkage


roof headliner



powder coated buddy bucket frame and seats ready for restoration









A/C parts






rear glass and front and rear glass trim



repo side lights. a new oldstock volt meter with broken needle. bought to modify the factory cluster




dash clusters and new oldstock wiring







hood and aluminum grill


I replaced the dash with an uncut one



CPP brake booster



nice stock steering wheel












repo inner fender wells



repo rally wheel outer rings



repo driverside bedside




























cool model

[zamboni2354]

am/fm stereo. also have an am radio



replacement LED lights for dash cluster, gas tank mounting parts, oem washer and bracket. ducting

[zicc1835]

somebody closer than me needs to grab this deal & a bump for you

[ho70]

THE BUCKETS AND RADIO ARE WORTH OVER 1K ALONE
Wish I was in the same country

[jr1000yarder]

Wonder how I could get it to the east coast ....I'd love to have this

[zamboni2354]

Originally Posted by jr1000yarder

Wonder how I could get it to the east coast ....I'd love to have this

I can strap it all down and help load it if you find someone to transport it. 😀

[zamboni2354]

Also includes one never worn brothers 3xl shirt and one lightly worn 2xl. 😀

[boonedogs72]

could you get this all loaded and secured enough to transport in an open carrier?? I'm up in redding ca but no a guy that runs a route up north from you.

[zamboni2354]

Originally Posted by boonedogs72

could you get this all loaded and secured enough to transport in an open carrier?? I'm up in redding ca but no a guy that runs a route up north from you.

yes, I could do that. Currently everything is in the cab or bed of the truck with the exception of the hood, buddy bucket frame and a few other smaller parts. I could get those in it and strap everything down really well for safe travels.

jeff

[boonedogs72]

Ok let me check shipping cost and if not to bad I'll be back in touch if you still have it.