|
06-29-2016, 08:59 PM
|
#1 |
|
Registered User
Join Date: Feb 2015
Location: Morganton, NC
Posts: 108
|
Dimple die question
Ok sheet metal question... I'm considering getting a set of dimple dies. How large of an arbor press would I need to use, let's say, a 2.5" to 3" die ? Thank you in advance.
__________________
Better to remain silent and be thought a fool than to open your mouth and remove all doubt. - Mark Twain |
|
|
|
06-29-2016, 09:02 PM
|
#2 |
|
Registered User
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,727
|
Re: Dimple die question
How thick of sheet metal do you plan on dimpling? 20ga a lot less press than 10ga...
Personally, the Harbor Freight 20 ton press probably the best way to go regardless as it gives you a lot of power for not a lot of money.
__________________
44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax |
|
|
|
|
06-29-2016, 09:12 PM
|
#3 |
|
Registered User
Join Date: Feb 2015
Location: Morganton, NC
Posts: 108
|
Re: Dimple die question
My bad. What guage are the door panels on a 67-68 ? 18-22 or so ? 18-22 guage steel and/or aluminium...
__________________
Better to remain silent and be thought a fool than to open your mouth and remove all doubt. - Mark Twain |
|
|
|
|
06-30-2016, 01:18 PM
|
#4 |
|
Registered User
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,727
|
Re: Dimple die question
I'd consider the 20 ton HF press pretty much regardless. Will let you press on/off bearings and other projects in addition to the dimple dies. I think somebody may make one that you can dimple using a bolt setup?
May want to Google that or check out Pirate4x4.com for some dimple die projects and how they did them.
__________________
44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax |
|
|
|
|
06-30-2016, 01:27 PM
|
#5 |
|
Registered User
Join Date: Apr 2012
Location: san diego ca
Posts: 618
|
Re: Dimple die question
check this tool out for dimple dies. I just bought 2 of the hydraulic guns.. need to get the dies and find something to dimple. http://www.hammerfab.com/page2/index.html
|
|
|
|
|
06-30-2016, 01:52 PM
|
#6 |
|
Registered User
Join Date: Feb 2015
Location: Morganton, NC
Posts: 108
|
Re: Dimple die question
Thx a lot for the info guys.
__________________
Better to remain silent and be thought a fool than to open your mouth and remove all doubt. - Mark Twain |
|
|
|
|
06-30-2016, 02:08 PM
|
#7 |
|
Senior Member
 Join Date: Mar 2003
Location: Colfax-California
Posts: 8,637
|
Re: Dimple die question
My experience is get the biggest one that you can afford. 20 ton minimum
|
|
|
|
|
06-30-2016, 02:26 PM
|
#8 |
|
Registered User
Join Date: May 2014
Location: Freedom Pa
Posts: 139
|
Re: Dimple die question
I've done 1/8" plat on my HF 20 ton. It did it but it was maxed out for sure. It worked well but just didn't have the grunt to really flatten the plate out. I had to kind of roll it into place as I welded it. I think it will work great for any thing under 1/8". Here is a pic of my chevelle frame that I made the plates for.
|
|
|
|
|
06-30-2016, 09:57 PM
|
#9 |
|
Registered User
Join Date: Mar 2012
Location: Evanston
Posts: 304
|
Re: Dimple die question
I do 3/16 with my harbor freight press it's no problem. The set I bought is made by Pacific customs and it's absolutely excellent and the full set is 350 ish .5"-3". Also if you do dimples on narrow pieces like box plates they will distort because there's not enough material to keep the shape. Here's a couple of my projects and I strongly suggest you get a plasma with hole stencils if you want to do anything more than sheet metal
__________________
My Patinia'd 69 69-http://67-72chevytrucks.com/vboard/showthread.php?t=517537 My RHD 68 http://67-72chevytrucks.com/vboard/s...d.php?t=594928 |
|
|
|
 |
| Bookmarks |
| Tags |
| sheet metal |
|
|
Linear Mode
