The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-04-2016, 06:35 PM   #1
Richya
Registered User
 
Join Date: Jun 2016
Location: Las vegas
Posts: 12
raised bed floor..tailgate not clossing

i raised my bed floor and now the tailgate dont close. ive seen other post were you have to cut an inch out off the bed to get it to close. i dont want to do that has anybody seen or tried to notch the inside of the tailgate.
Richya is offline   Reply With Quote
Old 07-04-2016, 06:50 PM   #2
bbbc10
Diggin The SquareLife
 
Join Date: Dec 2010
Location: garland,tx
Posts: 1,933
Re: raised bed floor..tailgate not clossing

Dont notch the tailgate thats lazy jus cut the inch out
bbbc10 is offline   Reply With Quote
Old 07-04-2016, 07:01 PM   #3
Richya
Registered User
 
Join Date: Jun 2016
Location: Las vegas
Posts: 12
Re: raised bed floor..tailgate not clossing

do you know of any post or links showing how and where to cut?
Richya is offline   Reply With Quote
Old 07-04-2016, 09:13 PM   #4
bbbc10
Diggin The SquareLife
 
Join Date: Dec 2010
Location: garland,tx
Posts: 1,933
Re: raised bed floor..tailgate not clossing

Take the 1" section from the tailgate end of the floor just mark 1" all across an cut it out an weld back up if i find the write up i will post it
bbbc10 is offline   Reply With Quote
Old 07-05-2016, 09:33 AM   #5
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
Re: raised bed floor..tailgate not clossing

How was the bed floor raised? Any recommendation on whether notching the floor or bed needs to be based on specific info. Also, how one goes about notching either part reflects on the final quality as well so I wouldn't be so quick to claim either way as a 'lazy' option.
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides
@rattlecankustoms in IG

Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive.
It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.....

Cubic inches is like Indiana Jones with a cheap pistol.
SCOTI is offline   Reply With Quote
Old 07-05-2016, 03:06 PM   #6
Richya
Registered User
 
Join Date: Jun 2016
Location: Las vegas
Posts: 12
Re: raised bed floor..tailgate not clossing

The floor was raised by taking 9 inches out of the side and the front and welding it back on. If I do cut an inch out of the rear do you cut through the cross member or remove it and then cut? Any help would be appreciated.
Attached Images
 
Richya is offline   Reply With Quote
Old 07-05-2016, 04:42 PM   #7
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
Re: raised bed floor..tailgate not clossing

Quote:
Originally Posted by Richya View Post
The floor was raised by taking 9 inches out of the side and the front and welding it back on. If I do cut an inch out of the rear do you cut through the cross member or remove it and then cut? Any help would be appreciated.
You'll prob need to slice through the support cross member as well. I looked @ shortening the floor or notching the gate. The lower portion of the gate was much easier in my opinion. Mine 'worked' fine too & wasn't noticeable w/the gate down.

I say 'worked' because when I got it Line-X'd, he was a little overzealous on the application of material applied when spraying the vertical portion of the bed floor & the lower portion of the gate (from the handle relocator down). I asked him to do just a single pass for each of those areas & said I would just paint/blend it the rest of the way. Instead, he laid down the same amount of material as the floor/sides which caused interference once closed (no interference before that).

No biggie to me. I'll just recess the gate a little more & have him re-spray that section.
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides
@rattlecankustoms in IG

Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive.
It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.....

Cubic inches is like Indiana Jones with a cheap pistol.
SCOTI is offline   Reply With Quote
Old 07-05-2016, 05:14 PM   #8
Richya
Registered User
 
Join Date: Jun 2016
Location: Las vegas
Posts: 12
Re: raised bed floor..tailgate not clossing

I actually like the idea of cutting the gate and would rather do it than cutting the floor. Do you have any pictures of your tailgate notched? I'm not sure how to go about cutting it. Thanks
Richya is offline   Reply With Quote
Reply

Bookmarks

Tags
floor, raised, tailgate


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:10 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com