The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > LSx Swaps

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-04-2017, 05:05 PM   #1
pete57
Registered User
 
Join Date: Mar 2013
Location: estill springs, tennessee
Posts: 74
Is 1 16in fan enough for a 5.3 swap?

Doing a 5.3 swap on my '64, i went with a champion 3 core rad and shroud with 1 16in maradyne 2170cfm electric fan. I will be running vintage air a/c later on. will this set up get the job done? Saw a dual fan set up on a camaro today at the pick n pull, just wondering if that would work better. Thanks..
pete57 is offline   Reply With Quote
Old 02-04-2017, 10:37 PM   #2
darrellyates
Registered User
 
Join Date: Jul 2016
Location: Gallatin TN
Posts: 376
Re: Is 1 16in fan enough for a 5.3 swap?

Quote:
Originally Posted by pete57 View Post
Doing a 5.3 swap on my '64, i went with a champion 3 core rad and shroud with 1 16in maradyne 2170cfm electric fan. I will be running vintage air a/c later on. will this set up get the job done? Saw a dual fan set up on a camaro today at the pick n pull, just wondering if that would work better. Thanks..
there are going to be those on here more knowledgable that I, however, I think you'll be OK. I ran the stock Tahoe (belt driven) fan on my first '68 with a 5.3 swap, and it ran 183 degrees all day, every day with a stock big block radiator. If it sat and idled for 30 minutes it would get up to about 201, but start moving and it came right down. The 5.3's are really not that hard to cool.... I would say you are fine.

Good Luck!!!
darrellyates is offline   Reply With Quote
Old 02-04-2017, 11:09 PM   #3
pete57
Registered User
 
Join Date: Mar 2013
Location: estill springs, tennessee
Posts: 74
Re: Is 1 16in fan enough for a 5.3 swap?

Cool, Thanks. The engine is a 2005 and came with dual fans but wouldnt fit in the '64. I was hoping a single fan would be ok.
pete57 is offline   Reply With Quote
Old 02-05-2017, 10:58 AM   #4
Clyde65
1965 Chevy C10, 2005 4.8L/4l60
 
Clyde65's Avatar
 
Join Date: Aug 2004
Location: DFW Texas
Posts: 8,546
Re: Is 1 16in fan enough for a 5.3 swap?

Without ac you should be ok. When you put ac on there go to the biggest puller fans you can fit. If it were me, I would go with dual now, no sense in doing things twice. Good luck!
__________________
Clyde65

Rebuild of Clyde
http://67-72chevytrucks.com/vboard/s...84#post8338184

69 Aristocrat Lo Liner build
http://67-72chevytrucks.com/vboard/s...84#post7561684



support our troops!
Clyde65 is offline   Reply With Quote
Old 02-06-2017, 12:19 PM   #5
pete57
Registered User
 
Join Date: Mar 2013
Location: estill springs, tennessee
Posts: 74
Re: Is 1 16in fan enough for a 5.3 swap?

Quote:
Originally Posted by Clyde65 View Post
Without ac you should be ok. When you put ac on there go to the biggest puller fans you can fit. If it were me, I would go with dual now, no sense in doing things twice. Good luck!
Thanks. Guess ill go get those camaro fans from pick n pull before someone else does.
pete57 is offline   Reply With Quote
Old 02-06-2017, 01:54 PM   #6
solidaxel
Registered User
 
solidaxel's Avatar
 
Join Date: Dec 2002
Location: Cactus Patch So. Az
Posts: 4,749
Re: Is 1 16in fan enough for a 5.3 swap?

With a shroud and a good 13VDC to the fan at idle you should be OK
Hold a rag or towel in front of the grill and see if the fan will pull it into to grille, if I can do that with mine it cools well even with A/C in the desert!
__________________
53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD)
53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25
55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73
62 Solidaxle Corvette Roman Red (327
340hp 4spd 3:36) C4 & C5 suspension tube chassis
LS 3 4L70E
65 Corvette Coupe 327 350hp 4spd 4:11
78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42
2000 S-Type 3.0 (wife cruiser)
2003 GMC SCSB 5.3 4L60E 3:42
solidaxel is offline   Reply With Quote
Old 02-06-2017, 07:02 PM   #7
crazy longhorn
Fabricate till you "puke"
 
Join Date: Jun 2002
Location: Ill
Posts: 9,402
Re: Is 1 16in fan enough for a 5.3 swap?

Quote:
Originally Posted by Clyde65 View Post
Without ac you should be ok. When you put ac on there go to the biggest puller fans you can fit. If it were me, I would go with dual now, no sense in doing things twice. Good luck!
Agree! There is more time /money, in doing it 2 times! I have not played with the AC, but run 2-14" fans on my truck.....that old 5.3 runs right on temp, & the fans dont run much at all. The fans are said to pull 1250-1300 ea, never an issue. Longhorn
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....
crazy longhorn is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:11 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com