Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
06-12-2018, 10:56 PM | #1 |
Registered User
Join Date: Jun 2017
Location: Bonsall, CA
Posts: 104
|
Front brake caliper orientation
I believe these are on upside down, from what I understand the bleeder should be up. Does anybody know if I can swap the line with the bleeder or do I need to swap sides? These came attached to the spindles this way, heck maybe its okay.
|
06-12-2018, 11:05 PM | #2 |
Senior Member
Join Date: Oct 2014
Location: Eagle, ID
Posts: 3,063
|
Re: Front brake caliper orientation
You are right, it's wrong the way it is now. Switch sides and you'll be fine
|
06-13-2018, 12:01 AM | #3 |
Registered User
Join Date: Jun 2006
Location: Idaho
Posts: 8,800
|
Re: Front brake caliper orientation
Yep, you will get air pockets in the top, been there....
__________________
1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project |
06-13-2018, 10:37 AM | #4 |
Registered User
Join Date: Jun 2017
Location: Bonsall, CA
Posts: 104
|
Re: Front brake caliper orientation
Thanks, you know you look at something then you go "wait, what the heck!" that was my moment while working on the bottom of my truck. These had been on for a while as I built out the break lines, bleed them, trouble shot other issues with the brakes, then I was looking and the light bulb blinked on. Guess I get to bleed the fronts one more time, the wife will be so excited to be a pedal pusher again.
|
06-13-2018, 04:46 PM | #5 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,333
|
Re: Front brake caliper orientation
check out the one man bleeder, time and wife saver. the less they see inside your shop the better, haha.
hose goes into container with brake fluid in it so hose sits on bottom of the container, other end of hose fits snuggly over the bleeder screw. put some fluid in the container so the hose is covered, say 1/2" deep. open the screw and pump the brakes slowly yourself. clear tubing works the best because you can see if there are bubbles in the line still. don't open the bleeder screw too much or it can/will suck air in around the bleeder screw threads. you tube it. works great. you can make one with an old soda bottle. the lid needs to have a vent though as well as the hole the tube goes into. |
06-13-2018, 05:05 PM | #6 |
Registered User
Join Date: Jun 2006
Location: Idaho
Posts: 8,800
|
Re: Front brake caliper orientation
I used Speed Bleeders, makes it a one man operation.
__________________
1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project |
06-13-2018, 09:27 PM | #7 |
Registered User
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,711
|
Re: Front brake caliper orientation
Just because I am curious, what calipers are those?
__________________
Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around. |
06-13-2018, 11:26 PM | #8 |
Registered User
Join Date: Jun 2017
Location: Bonsall, CA
Posts: 104
|
Re: Front brake caliper orientation
The front end kit came from TCI, with the brakes. I believe I found them in the CPP catalog as the “big brake”.
Capilers are swapped and bleed, done now on to other issues. |
06-14-2018, 12:18 AM | #9 |
Registered User
Join Date: Jun 2017
Location: Bonsall, CA
Posts: 104
|
Re: Front brake caliper orientation
Found them in CPP universal catalog. Big Bore Metric CP412526.
|
06-14-2018, 07:09 AM | #10 | |
Senior Member
Join Date: Jan 2016
Location: Appleton Washington
Posts: 592
|
Re: Front brake caliper orientation
Quote:
|
|
06-14-2018, 01:30 PM | #11 |
Registered User
Join Date: Jan 2012
Location: Motown
Posts: 7,680
|
Re: Front brake caliper orientation
looks like 86 monte carlo front caliper
gm used them on 733 vehicles according to autozone fitment chart pretty much any 82 to 89 gm vehicle chevy used them on s10, camaro, monte, malibu, elco and postal vehicles looks the same as what's on my fatman mustII
__________________
cool, an ogre smiley Ogre's 58 Truk build how to put your truck year and build thread into your signature shop air compressor timer |
06-14-2018, 05:05 PM | #12 |
Registered User
Join Date: Jul 2017
Location: Joshua, Texas.
Posts: 1,303
|
Re: Front brake caliper orientation
GM really liked to keep using the same parts over and over huh.
Is this one of those calipers that works with the bare bones disc conversion kits? The ones that only supply brackets and bolts and you need to find your own calipers and rotors?
__________________
1950 Build |
06-14-2018, 06:04 PM | #13 |
Registered User
Join Date: Jan 2018
Location: Knoxville TN
Posts: 87
|
Re: Front brake caliper orientation
I just recently went through and replaced most of the brake system on a 49 GMC someone else had built many moons ago. I spent more time researching the components than actually doing the repairs. If the builder made notes I didn't get them....
The comment about GM providing the basis for most of the calipers for these aftermarket kits definitely rings true in my case. I used calipers spec'ed for a 79 C10 as well as the flex lines and they bolted right up. Only thing is, to keep the bleeders on the top side when mounted, the calipers had to be swapped, i.e. the "R" labeled caliper is mounted on the left and the "L" labeled caliper is mounted on the right. They work pretty good considering they're controlled by a firewall mounted 75 Pinto dual diaphragm power booster, master cyl and combo valve...... Johnny Cash would be proud LOL. |
06-15-2018, 02:03 AM | #14 | |
Registered User
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,711
|
Re: Front brake caliper orientation
Quote:
I did find The CPP instruction sheet http://www.classicperform.com/Instru...F/CP412526.pdf But you know what they say, who reads the instructions.
__________________
Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around. |
|
Bookmarks |
|
|