TN WTB looking for usable, reasonable, complete HEI distributor for Inline 6 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

hotsam · 08-05-2018, 10:25 AM

wanting to convert to HEI (250 inline 6) thanks.

**Ironhorse** · 08-05-2018, 10:45 AM

Just a suggestion and a thought but you might consider doing a Petronix ignition conversion. They make a 6 cylinder unit for both 6 volt and 12 volt systems. I converted my '71 4x4 using original stock GM points distributor and stock cap. Worked out really well since the V8 4x4 engine sits further back on the frame I did not have room for a large cap HEI distributor. This solved the problem and gives a stock looking engine compartment. Just some thoughts.

Good luck on your project.

hotsam · 08-05-2018, 11:23 AM

Thanks IronHorse ! I do like the Petronix stuff, but this is a basket case project and I do not have the (or any ) distributor assembly at all... just thought getting an hei unit would be quickest and easiest. And would rather have good used than chinese....

**Ironhorse** · 08-05-2018, 11:48 AM

If interested I think my BIL, old wagon, has a 6 cylinder distributor from a '67 GMC he is parting, that would be a 12 volt system. Should be compatible to your square body I would think. Might contact him, just a thought.

obijuan · 08-05-2018, 03:48 PM

I've got an msd distributor and coil I bought for my 292. New in box. You interested in something like that?

natedogg · 08-05-2018, 03:56 PM

Pm

D13 · 08-06-2018, 06:21 AM

Pick up a Skip White on evilflay. Drop in no muss no fuss. don't forget to put on good wires, replace the resisot wire, and up the plug gap.

jdl71 · 08-06-2018, 06:12 PM

I've got a gm one

08-05-2018, 10:25 AM	#1
hotsam Registered User Join Date: Mar 2013 Location: East TN. Posts: 371	WTB looking for usable, reasonable, complete HEI distributor for Inline 6 wanting to convert to HEI (250 inline 6) thanks. __________________ 1972 k10 Custom 10 Deluxe, short bed 4x4, 454, 4 speed (Sold) 1985 K30 Dump Truck 1986 Jeep CJ-7 1955 2 door 210 post

08-05-2018, 10:45 AM	#2
Ironhorse Senior Member Join Date: Jul 2001 Location: Wellington, Ks Posts: 10,294	Re: WTB looking for usable, reasonable, complete HEI distributor for Inline 6 Just a suggestion and a thought but you might consider doing a Petronix ignition conversion. They make a 6 cylinder unit for both 6 volt and 12 volt systems. I converted my '71 4x4 using original stock GM points distributor and stock cap. Worked out really well since the V8 4x4 engine sits further back on the frame I did not have room for a large cap HEI distributor. This solved the problem and gives a stock looking engine compartment. Just some thoughts. Good luck on your project. __________________ 1971 Chevy 1/2T 4x4 LWB 350 V-8 Was sm465-now 350TH/np205 Tilt, Tach, Towhooks Original Truck AM/FM Wellington, Ks

08-05-2018, 11:23 AM	#3
hotsam Registered User Join Date: Mar 2013 Location: East TN. Posts: 371	Re: WTB looking for usable, reasonable, complete HEI distributor for Inline 6 Thanks IronHorse ! I do like the Petronix stuff, but this is a basket case project and I do not have the (or any ) distributor assembly at all... just thought getting an hei unit would be quickest and easiest. And would rather have good used than chinese.... __________________ 1972 k10 Custom 10 Deluxe, short bed 4x4, 454, 4 speed (Sold) 1985 K30 Dump Truck 1986 Jeep CJ-7 1955 2 door 210 post

08-05-2018, 11:48 AM	#4
Ironhorse Senior Member Join Date: Jul 2001 Location: Wellington, Ks Posts: 10,294	Re: WTB looking for usable, reasonable, complete HEI distributor for Inline 6 If interested I think my BIL, old wagon, has a 6 cylinder distributor from a '67 GMC he is parting, that would be a 12 volt system. Should be compatible to your square body I would think. Might contact him, just a thought. __________________ 1971 Chevy 1/2T 4x4 LWB 350 V-8 Was sm465-now 350TH/np205 Tilt, Tach, Towhooks Original Truck AM/FM Wellington, Ks

08-05-2018, 03:48 PM	#5
obijuan Registered User Join Date: Jun 2012 Location: cibolo tx Posts: 1,033	Re: WTB looking for usable, reasonable, complete HEI distributor for Inline 6 I've got an msd distributor and coil I bought for my 292. New in box. You interested in something like that? __________________ 1985 k5 396/nv4500/203/205 d60/d70 4.56 42 sx2 1991 V3500 350/4l80/205 60/14 4.10 35 toyos.

08-05-2018, 03:56 PM	#6
natedogg Registered User Join Date: Dec 2013 Location: West, TN Posts: 312	Re: WTB looking for usable, reasonable, complete HEI distributor for Inline 6 Pm

08-06-2018, 06:21 AM	#7
D13 Registered User Join Date: Feb 2007 Location: Memphis MI Posts: 1,851	Re: WTB looking for usable, reasonable, complete HEI distributor for Inline 6 Pick up a Skip White on evilflay. Drop in no muss no fuss. don't forget to put on good wires, replace the resisot wire, and up the plug gap. __________________ 1987 2 ton 1982 250/TH350 beater in progress Dad's 1981 3/4 L6 3 on tree posi and no options, awaiting restoration or scrapping Plus a mess o' tractors

08-06-2018, 06:12 PM	#8
jdl71 Registered User Join Date: Oct 2012 Location: Eldon, MO Posts: 1,753	Re: WTB looking for usable, reasonable, complete HEI distributor for Inline 6 I've got a gm one __________________ Psalm 23 64 C10 66 K20



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.