TX Blazer Parts

[boynton]

I have several blazer parts here. I am getting these posted late at night so I will probably overlook some pricing but will get it straightened out tomorrow if I do. Shipping is all over the place so prices are plus shipping. I will ship things as economical as possible and use shipping materials I already own for free (recycled). If I have to purchase shipping materials for an odd shaped item it will be in addition to the amount for shipping. I’m not going to make any money on shipping but I don’t want to spend everything getting it done either. The hatch slides and NP205 shifter and bolt are sold.

I do have one shifter knob still available $25 sold
Hatch side latch $100 pr
Windshield frame repair pieces $130-for all three-missing the passenger corner
Rubber bushings/bump stops $10 for all

[boynton]

Fuel filler cover repairable rust at bottom edge, all mounting flanges are solid. $40

Fuel tank vapor/vent tube with support strap-$30

Fuel tank strap sets $80

[1rippen6]

I'll take the available shifter knob, are the shifter boot and rings available, if so I would be interested pending price. If the inner piece is full length, I will also be interested in the windshield header patches.

[Tuff Gong]

Price on shifter knob and steps if you are selling

[boynton]

Straps rubber pieces photos

Fuel hose for under the bed with bracket $10 bracket is slightly tweaked.

[boynton]

Originally Posted by Tuff Gong

Price on shifter knob and steps if you are selling

Steps are sold. Rippen is 1st on the knob but it is $25. Steps are $140-1 is tweaked a bit.

[boynton]

Originally Posted by 1rippen6

I'll take the available shifter knob, are the shifter boot and rings available, if so I would be interested pending price. If the inner piece is full length, I will also be interested in the windshield header patches.

Knob is yours. Shifter boots and rings are available-$50 for both or $35 you pick one. The inner piece is missing the right side 5-6” or so. The only complete piece is the drip rail.

[boynton]

Sold. More steps photos $140 one step is tweaked/pushed back

[boynton]

NP205 frame brackets $45 set
Single small angle bracket $15

[boynton]

Tailgate vertical weatherstrips $25 pr two holes drilled in one.

[boynton]

Sold NP205 shift rails and ring gear-I don’t remember what it is, maybe someone can enlighten us. I put a twin stick kit in my truck and these are my leftover parts. Package deal for all $50 sold

[boynton]

Unbolts for leaf springs with lift blocks $15 (these are heavy)

Beat up tailgate piece for hatch $15 not sure it’s worth shipping but I will.

Rear driveshaft slip section $10

[boynton]

Drive shaft slip section $10

[boynton]

Sold NP205 shift rings and boots $35 each sold

[boynton]

Right quarter whole $300-Texas truck. Minimal rust just dings galore. Main areas of rust are the front lower section that is cut already and the top of the bedside where the top attaches. Very solid. The top could be treated and worked but the front lower section will need to repair. I have a lot of photos of this quarter I can text out 254-338-1489

[boynton]

Lower front section

[boynton]

More of the quarter

[boynton]

Last set for now

[boynton]

I will be headed to the Dallas/FT Worth on the 25th to the 30th of December if someone wants to meet up for some parts. I will be in the area of Green Oaks/I-20 that week. I will not have much time to travel far from that location but I can bring large items if you give me a heads up and get them paid for.

If you don’t like my prices make an offer. Buy multiple items and save a little. I think my prices are fair but I’m not an expert.

[boynton]

If anyone has some painted front 4x4 dog dish caps I’d be interested in those on trade.

[Tmend]

Sir may I see photos of the hatch latches and how much are you asking for he hatch lift stays/supports. Thanks much you can send me text if easier

[boynton]

Originally Posted by Tmend

Sir may I see photos of the hatch latches and how much are you asking for he hatch lift stays/supports. Thanks much you can send me text if easier

I will get them to you when I get home tonight.

[1rippen6]

I'll take the shifter knob and both boot and rings shipped to 17225. If you want to separate the linkage off the shifter rails, I'd be interested in that also.

[Tuff Gong]

I will pass on the steps. Thank you for the photos

[boynton]

Originally Posted by Tuff Gong

I will pass on the steps. Thank you for the photos

Not a problem that’s why I post as many pictures as I can. There is a board member that makes reproduction steps for $280 if you want a set you don’t have to work on.