97 computer?? needed - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Suicide-D · 01-28-2005, 10:16 PM

I found a low mile vortec 350 complete & tranny out of a 97 truck. I want to put this in my 92.the thing it doesn't have is the computer and harness. Anybody know where I can find one? or atleast what I should expect to pay.

Thanks,
D

Suicide-D · 01-28-2005, 10:17 PM

will I need a different fuel pump for it also?

*bisquik65* · 01-28-2005, 11:02 PM

You will probally need an aftermarket harness as the 97 harness is also part of the body harness,You also need the mass air flow meter,ecm,and the fuel pump pressure is 35-45 lbs for the vortec motor.. But as far as bolting it in,not a bad job.... Try looking for a harness ,some companys ask you what you are putting it in and what year engine and will make a custom one...Hope this helps some,Erick

NPilot1975 · 01-29-2005, 09:55 AM

Try painless for your harness and Street and Performance should be able to get you a computer (although finding one at the junk yard would be much cheaper.)

oldyeller · 01-30-2005, 06:15 AM

I disagree with bisquik, you will need a pump that can maintain 60 psi. the vortec needs a minimum of 50 psi to start up. most vortecs i have worked on maintain 55 to 62 psi. you might be able to get a tank and all out of a vortec truck and bolt it in yours. it would be easier than trying to retrofit a different pump on to your tank setup.

try http://www.car-part.com for a good idea of junkyard prices...

Suicide-D · 01-31-2005, 08:34 AM

Thanks for the input. Sorry I haven't responded sooner...I have a virus I guess... Shut my whole system down at home.That or I had a hard drive go bad.

Thanks,
D

TEXAS 68 · 01-31-2005, 05:30 PM

You should be able to just swap in pump and sending unit in your tank. as far as harness goes since you don't have one you can buy for price http://www.paceparts.com/index.asp?P...D&ProdID=73236 and get computer from salvage yard. You also need to consider if you going to keep all yhe emissions or not. I'm still learning on this also,so if I'm wrong on any of this please chime in.

NPilot1975 · 02-01-2005, 01:54 AM

Summit is cheaper than Pace for the painless harness. If you do not keep the emissions, you will need to reprogram the computer, Speartech out of IN can do it for you. I will look and see if I still have there website.

Suicide-D · 02-01-2005, 08:42 AM

emissions will have to stay, atleast as long as I stay in this county... which that doesn't look like it's gonna change.

TEXAS 68 · 02-01-2005, 09:55 AM

Check out some local salvage yards for what you need, I might be able to help you out on the harness if you need a stock one. BTW nice website

99-2door · 02-01-2005, 12:41 PM

You can modify the stock harness to fit the older trucks. Better than paying over $500 for one from painless.
In fact there is a company on ebay that will do it for you for around $200 I think.

NPilot1975 · 02-02-2005, 01:22 AM

I initially had mine modified, cost me $400 dollars for an LT-1. It had no fuses, lots of electrical tape, and any thing I planned on deleting, the wiring was just clipped and tucked into the loom. I would spend a little more the first time and go with a good harness. I junked the original and got a painless. It hurt for the money but was more than worth it.

99-2door · 02-02-2005, 01:59 AM

Hey Npilot, what did you do to make the AC compressor clear on your truck. Did you just notch? Got a project with an LT-1 in a 70. Thanks

NPilot1975 · 02-02-2005, 08:22 AM

I went with Street & Performance accessories.

01-28-2005, 10:16 PM	#1
Suicide-D Registered User Join Date: Jan 2001 Location: Katy, TX...but the love of my life resides in Dublin,OH. Posts: 1,408	97 computer?? needed I found a low mile vortec 350 complete & tranny out of a 97 truck. I want to put this in my 92.the thing it doesn't have is the computer and harness. Anybody know where I can find one? or atleast what I should expect to pay. Thanks, D

01-29-2005, 09:55 AM	#4
NPilot1975 Senior Member Join Date: Aug 2002 Location: Plymouth, MA Posts: 891	Try painless for your harness and Street and Performance should be able to get you a computer (although finding one at the junk yard would be much cheaper.) __________________ 1972 Blazer body...need to get a thread started for the rest of the story

01-30-2005, 06:15 AM	#5
oldyeller Captain CAAAVVVMMMAAANNN! Join Date: Mar 2002 Location: Anna Texas Posts: 726	I disagree with bisquik, you will need a pump that can maintain 60 psi. the vortec needs a minimum of 50 psi to start up. most vortecs i have worked on maintain 55 to 62 psi. you might be able to get a tank and all out of a vortec truck and bolt it in yours. it would be easier than trying to retrofit a different pump on to your tank setup. try http://www.car-part.com for a good idea of junkyard prices... __________________ 72 LWB Fleetside C10 Custom 350/350 97 GMC Yukon 4X4 SLT Anna, Texas check out the project old yeller

01-31-2005, 05:30 PM	#7
TEXAS 68 Vortec in the works Join Date: Nov 2003 Location: Spring,Texas Posts: 735	You should be able to just swap in pump and sending unit in your tank. as far as harness goes since you don't have one you can buy for price http://www.paceparts.com/index.asp?P...D&ProdID=73236 and get computer from salvage yard. You also need to consider if you going to keep all yhe emissions or not. I'm still learning on this also,so if I'm wrong on any of this please chime in. __________________ 68? It's all figured out untill you get it apart. Is it Sunday yet??? 68 Project 68 SWB frame off/98 Vortec with stock FI/power everything. 95 ECLB 2500 with 346,000 on the clock(the original HD) 99 Lesabre-wifes ride 08 Crew Cab LTZ-All Mine 89 SWB 5/7 drop-Son's first ride.

02-01-2005, 01:54 AM	#8
NPilot1975 Senior Member Join Date: Aug 2002 Location: Plymouth, MA Posts: 891	Summit is cheaper than Pace for the painless harness. If you do not keep the emissions, you will need to reprogram the computer, Speartech out of IN can do it for you. I will look and see if I still have there website. __________________ 1972 Blazer body...need to get a thread started for the rest of the story

01-28-2005, 10:17 PM	#2
Suicide-D Registered User Join Date: Jan 2001 Location: Katy, TX...but the love of my life resides in Dublin,OH. Posts: 1,408	will I need a different fuel pump for it also?

01-28-2005, 11:02 PM	#3
bisquik65 Account Suspended Join Date: Apr 2004 Location: N.C. high country Posts: 6,107	You will probally need an aftermarket harness as the 97 harness is also part of the body harness,You also need the mass air flow meter,ecm,and the fuel pump pressure is 35-45 lbs for the vortec motor.. But as far as bolting it in,not a bad job.... Try looking for a harness ,some companys ask you what you are putting it in and what year engine and will make a custom one...Hope this helps some,Erick

01-31-2005, 08:34 AM	#6
Suicide-D Registered User Join Date: Jan 2001 Location: Katy, TX...but the love of my life resides in Dublin,OH. Posts: 1,408	Thanks for the input. Sorry I haven't responded sooner...I have a virus I guess... Shut my whole system down at home.That or I had a hard drive go bad. Thanks, D

02-01-2005, 08:42 AM	#9
Suicide-D Registered User Join Date: Jan 2001 Location: Katy, TX...but the love of my life resides in Dublin,OH. Posts: 1,408	emissions will have to stay, atleast as long as I stay in this county... which that doesn't look like it's gonna change.

02-01-2005, 09:55 AM	#10
TEXAS 68 Vortec in the works Join Date: Nov 2003 Location: Spring,Texas Posts: 735	Check out some local salvage yards for what you need, I might be able to help you out on the harness if you need a stock one. BTW nice website __________________ 68? It's all figured out untill you get it apart. Is it Sunday yet??? 68 Project 68 SWB frame off/98 Vortec with stock FI/power everything. 95 ECLB 2500 with 346,000 on the clock(the original HD) 99 Lesabre-wifes ride 08 Crew Cab LTZ-All Mine 89 SWB 5/7 drop-Son's first ride.

02-01-2005, 12:41 PM	#11
99-2door Registered User Join Date: Oct 2003 Location: Broken Bow, OK Posts: 1,385	You can modify the stock harness to fit the older trucks. Better than paying over $500 for one from painless. In fact there is a company on ebay that will do it for you for around $200 I think. __________________ 95 K3500 SRW 5.7L Vortec 4L80e 4.10 G80 2001 GMC C3 6.0 AWD, Volant, 3/5 drop TBSS intake, HP tuners, pullies, 05 efans, 05 front brakes, etc. 2003 Tahoe Z71 Silverado front clip

02-02-2005, 01:22 AM	#12
NPilot1975 Senior Member Join Date: Aug 2002 Location: Plymouth, MA Posts: 891	I initially had mine modified, cost me $400 dollars for an LT-1. It had no fuses, lots of electrical tape, and any thing I planned on deleting, the wiring was just clipped and tucked into the loom. I would spend a little more the first time and go with a good harness. I junked the original and got a painless. It hurt for the money but was more than worth it. __________________ 1972 Blazer body...need to get a thread started for the rest of the story

02-02-2005, 01:59 AM	#13
99-2door Registered User Join Date: Oct 2003 Location: Broken Bow, OK Posts: 1,385	Hey Npilot, what did you do to make the AC compressor clear on your truck. Did you just notch? Got a project with an LT-1 in a 70. Thanks __________________ 95 K3500 SRW 5.7L Vortec 4L80e 4.10 G80 2001 GMC C3 6.0 AWD, Volant, 3/5 drop TBSS intake, HP tuners, pullies, 05 efans, 05 front brakes, etc. 2003 Tahoe Z71 Silverado front clip

02-02-2005, 08:22 AM	#14
NPilot1975 Senior Member Join Date: Aug 2002 Location: Plymouth, MA Posts: 891	I went with Street & Performance accessories. Attached Images __________________ 1972 Blazer body...need to get a thread started for the rest of the story

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.