Looking for pics of an engine - The 1947 - Present Chevrolet & GMC Truck Message Board Network

my new 72 · 09-16-2005, 12:54 AM

Someone posted pics of their engine last week and I cannot seem to find it anywhere. It looked to be a black BB truck, but I'm not too sure. What I am looking for specificall is the pic of the dual inlet plumbing on the Holley that was made from 3/8 metal tube with a red pres. regulator and gauge mounted up front. I would like to duplicate the setup and want to show it to my brother. Thanks for the help with search down.

71Dragtruck · 09-16-2005, 01:26 PM

Is this the one?

my new 72 · 09-16-2005, 01:55 PM

yes, it sure is. Thank you very much. You don't mind if I copy that and make one do you? It will look killer on the 385 in my Brothers Impala.

my new 72 · 09-16-2005, 02:18 PM

not to be a pain, but could you maybe give me a rundown of the parts list and fitting sizes you used. Thanks.

71Dragtruck · 09-16-2005, 02:50 PM

Go right ahead, the reg is a Holley reg, the line is 3/8" stainless steel, the tee and the compression fittings are all 3/8" thread, the gauge is a Autometer. If you are going to a holley carb you won't need the x-overs at the fuel bowls.

my new 72 · 09-16-2005, 05:03 PM

Sweet, thanks alot 71.

09-16-2005, 12:54 AM	#1
my new 72 faster, faster, faster Join Date: Dec 2001 Location: Houston ,Texas ,USA Posts: 1,354	Looking for pics of an engine Someone posted pics of their engine last week and I cannot seem to find it anywhere. It looked to be a black BB truck, but I'm not too sure. What I am looking for specificall is the pic of the dual inlet plumbing on the Holley that was made from 3/8 metal tube with a red pres. regulator and gauge mounted up front. I would like to duplicate the setup and want to show it to my brother. Thanks for the help with search down. __________________ I'm going to Law School, wanna debate? It's good practice.

09-16-2005, 01:26 PM	#2
71Dragtruck Registered User Join Date: Jun 2004 Location: Saskatchewan, Canada Posts: 1,368	Is this the one? Attached Images Last edited by 71Dragtruck; 09-16-2005 at 01:27 PM.

09-16-2005, 01:55 PM	#3
my new 72 faster, faster, faster Join Date: Dec 2001 Location: Houston ,Texas ,USA Posts: 1,354	yes, it sure is. Thank you very much. You don't mind if I copy that and make one do you? It will look killer on the 385 in my Brothers Impala. __________________ I'm going to Law School, wanna debate? It's good practice.

09-16-2005, 02:18 PM	#4
my new 72 faster, faster, faster Join Date: Dec 2001 Location: Houston ,Texas ,USA Posts: 1,354	not to be a pain, but could you maybe give me a rundown of the parts list and fitting sizes you used. Thanks. __________________ I'm going to Law School, wanna debate? It's good practice.

09-16-2005, 02:50 PM	#5
71Dragtruck Registered User Join Date: Jun 2004 Location: Saskatchewan, Canada Posts: 1,368	Go right ahead, the reg is a Holley reg, the line is 3/8" stainless steel, the tee and the compression fittings are all 3/8" thread, the gauge is a Autometer. If you are going to a holley carb you won't need the x-overs at the fuel bowls. Last edited by 71Dragtruck; 09-16-2005 at 02:52 PM.

09-16-2005, 05:03 PM	#6
my new 72 faster, faster, faster Join Date: Dec 2001 Location: Houston ,Texas ,USA Posts: 1,354	Sweet, thanks alot 71. __________________ I'm going to Law School, wanna debate? It's good practice.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.