|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-28-2006, 12:52 PM
|
#1 |
|
Questionable
Join Date: Mar 2005
Location: Atlanta
Posts: 13,373
|
tranny output shaft questions / request for used part in ATL
I'm in a dilemma. I wanted to have my driveshaft fabbed today and didn't even think to get a new output shaft for my T56.
After talking to j and slow in chat last night, they mentioned the TH350 and 700R4 output shaft should be about the same as a T56 output shaft - guys at the tranny shop say I'm full of crap, the 700R4 and TH350 are totally different and the guys typically don't deal with the T56. Two things: 1) Anyone know if the 700R4 and T56 share the same output shaft as far as splines and size go? 2) Does anyone here around here in ATL have a 700R4 output shaft? I can think of one board member I might ask nearby, but curious to see if anyone else around here definitely has one before I ask. Thanks, as always  all I have left on the truck to finish is driveshaft, fuel delivery, install the harness and PCM and the hydraulic clutch linkage!!
__________________
If I've got anything up for grabs, it'll be here: 7-hole gauge cluster for a 67-72 p/u FREE (link) I can't check the forum daily. If I don't reply to you within 24 hours, drop me a PM! I'm (hopefully) still alive and will reply faster to a PM. |
|
|
|
03-28-2006, 01:49 PM
|
#2 |
|
It's a catastrophic success.
 
Join Date: Jan 2003
Location: Oklahoma
Posts: 2,077
|
Re: tranny output shaft questions / request for used part in ATL
A little reading.
http://www.chevyhiperformance.com/techarticles/60978/ |
|
|
|
|
03-28-2006, 04:42 PM
|
#3 |
|
Senior Member
Join Date: Aug 2003
Location: Conyers,Ga.
Posts: 7,289
|
Re: tranny output shaft questions / request for used part in ATL
There is a guy in Snellville that builds GM trasmissions. His name is Sid Neal. I don't have his #,but if you need it I can get it.
|
|
|
|
|
03-28-2006, 05:03 PM
|
#4 | |
|
Located in Buford,Georgia
Join Date: Apr 2005
Posts: 54
|
Re: tranny output shaft questions / request for used part in ATL
Would you guys know of any junk yards that would have 68 c10 parts?
Quote:
|
|
|
|
|
|
03-28-2006, 05:11 PM
|
#5 | |
|
Rottenwood Garage Member
Join Date: May 2005
Location: Marietta, Georgia
Posts: 4,321
|
Re: tranny output shaft questions / request for used part in ATL
Quote:
|
|
|
|
|
|
03-28-2006, 05:15 PM
|
#6 | |
|
Questionable
Join Date: Mar 2005
Location: Atlanta
Posts: 13,373
|
Re: tranny output shaft questions / request for used part in ATL
Quote:
You're the one guy I figured would have a pile of output shafts laying around!
__________________
If I've got anything up for grabs, it'll be here: 7-hole gauge cluster for a 67-72 p/u FREE (link) I can't check the forum daily. If I don't reply to you within 24 hours, drop me a PM! I'm (hopefully) still alive and will reply faster to a PM. |
|
|
|
|
|
03-28-2006, 05:24 PM
|
#7 |
|
Senior Member
Join Date: Aug 2003
Location: Conyers,Ga.
Posts: 7,289
|
Re: tranny output shaft questions / request for used part in ATL
I only have a few 700's, if it were turbo 350's you would be in luck.
|
|
|
|
|
03-29-2006, 08:25 AM
|
#8 | |
|
Located in Buford,Georgia
Join Date: Apr 2005
Posts: 54
|
Re: tranny output shaft questions / request for used part in ATL
Great. I'll send you a pm of all the parts that I need.
Quote:
|
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
