|
08-04-2006, 08:03 PM
|
#1 |
|
Registered User
Join Date: Dec 2005
Location: sarasota florida
Posts: 24
|
control arms needed?
hey guys whats goin on...i just recently put on my new rims/tires and it lifted the front end up..im runnin a 265/35/22 and was wondering if im gonna need tubular control arms to get the front to lay out..right now the crossmember is about 2 inchs or so off the ground..i want to get the crossmember laid out first so i dont have to make a bigger z than have too...thanks alot guys!
|
|
|
|
08-04-2006, 10:27 PM
|
#2 |
|
Seņor Member
Join Date: May 2002
Location: Edge of the world
Posts: 5,367
|
Re: control arms needed?
Tubular control arms aren't going to give you any additional clearance.
__________________
|
|
|
|
|
08-05-2006, 12:32 AM
|
#3 |
|
soon to be bagged64sub
Join Date: Feb 2005
Location: DFW-currently phoenix
Posts: 635
|
Re: control arms needed?
If you get plenty of lift I would check into cutting down the bottom cup a bit. Just make sure it wont rub if you cut it down. Im assuming you have spindles already and an upper plate, lower cup setup.
__________________
1969 c-10, bagged, Zd, 20" Boyds SOLD! 1964 Suburban COMING SOON  Build threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=3047261965 c-10 long bed 1993 Sierra x-cab 1999 tahoe-4/5 on 22s 2005 Chevy work truck |
|
|
|
|
08-05-2006, 01:39 AM
|
#4 |
|
Registered User
Join Date: Dec 2005
Location: sarasota florida
Posts: 24
|
Re: control arms needed?
yea have that already and the bottom cup is cut down to 1 inch already
|
|
|
|
|
08-05-2006, 04:31 PM
|
#5 |
|
Sold! 2 days after finished
Join Date: Oct 2005
Location: Ohio
Posts: 327
|
Re: control arms needed?
Take out the lower cup and weld a flat plate in the control arm. That might get you another inch.
|
|
|
|
|
08-06-2006, 12:50 AM
|
#6 |
|
Epoxy Primer Friendly
Join Date: Feb 2004
Location: South of Houston TEXXXAS
Posts: 680
|
Re: control arms needed?
If the truck is an 86 you dont need a lower cup just bolt it to the LCA. They are big enough. Just make sure to debur it and clean it all up.
|
|
|
|
|
08-06-2006, 04:42 PM
|
#7 |
|
Registered User
Join Date: Dec 2005
Location: sarasota florida
Posts: 24
|
Re: control arms needed?
i just ordered lowers so as soon as i get them im gonna put them in and see if it helps....im gonna put them in without the cup also so.....
|
|
|
|
|
08-08-2006, 11:29 AM
|
#8 | |
|
Junior Member
Join Date: Feb 2005
Location: Huntingburg IN
Posts: 620
|
Re: control arms needed?
Quote:
|
|
|
|
|
|
08-08-2006, 04:19 PM
|
#9 |
|
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: control arms needed?
...
Last edited by Shane; 08-08-2006 at 04:20 PM. |
|
|
|
|
08-08-2006, 05:04 PM
|
#10 |
|
Registered User
Join Date: Dec 2005
Location: sarasota florida
Posts: 24
|
Re: control arms needed?
yea i got 3 inch drop spinedles on there with a suicidedoors upper plate with a slam re-82
Last edited by laidout86; 08-08-2006 at 05:04 PM. |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
My Project 69 SWB
Linear Mode
