The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-30-2006, 08:42 PM   #1
72 cheyenne pdx
Registered User
 
72 cheyenne pdx's Avatar
 
Join Date: Nov 2006
Location: Portland
Posts: 382
How much lift in a bagged system

OK - i am swinging towards a bagged system in my truck, but need some insight. I am an avid fisherman/camper. In theory I want a a lower truck for cruising, but since I am really into fishing and camping, I would like to air up the bags so my truck is at stock height or even above stock. Are there bags out there that would do this? A lot of fishing/camping locations that I go to are on old logging/service roads and have a lot of potholes. If I can't get the height needed with bags, is there something that anybody recommends?


Thanks,
72 cheyenne pdx is offline   Reply With Quote
Old 11-30-2006, 09:06 PM   #2
jimmydean
Registered User
 
jimmydean's Avatar
 
Join Date: May 2005
Location: Beaverton, OR
Posts: 3,728
Re: How much lift in a bagged system

Well, if you run Slam Specialty RE7 bags, I think they are a total of 7" of travel. If you look at the picture I posted of my truck, you will see the front with air and 2.5" drop spindles is the same height it was stock. I can drop it to about 4" off the crossmember.

My truck isn't as low as some, but that is by design. I used RE7's up front and RE6's in the back. I also didn't cut my front cups and may install a small cup in the back to keep it off the ground.
jimmydean is offline   Reply With Quote
Old 11-30-2006, 09:12 PM   #3
project76
Registered User
 
project76's Avatar
 
Join Date: Nov 2004
Location: Cecil County Maryland
Posts: 135
Re: How much lift in a bagged system

Sounds like you would benifit from a rather simple setup. CPP has a nice bolt in notch for the rear and you can run bags in the stock location if you have a coil spring truck. On the front you can just run a set of bags and cups from suicidedoors. It will get you low enough to cruise and still get you back up to where you want to be for the rough roads.
__________________
Brandon
project 67 swb bagged on 20" Coddingtons

Last edited by project76; 11-30-2006 at 09:12 PM.
project76 is offline   Reply With Quote
Old 11-30-2006, 09:56 PM   #4
leftcoast66
Registered User
 
leftcoast66's Avatar
 
Join Date: Sep 2006
Location: Covington, WA
Posts: 770
Re: How much lift in a bagged system

Quote:
Originally Posted by project76 View Post
Sounds like you would benifit from a rather simple setup. CPP has a nice bolt in notch for the rear and you can run bags in the stock location if you have a coil spring truck. On the front you can just run a set of bags and cups from suicidedoors. It will get you low enough to cruise and still get you back up to where you want to be for the rough roads.
Even without a notch, mine sits about 12 inches off the ground in the back with the bag in stock location, and when the front end wasn't toyed with and had stock cups and factory spindles, it was a perfect setup and sat level.
leftcoast66 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:21 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com