headers for 454 into 63 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

harry · 03-07-2007, 02:55 AM

does any know of a bolt in header that will fit 454 into 63 and still running with the mechanical clutch system.(big block,block huggers???part#?)
cheers

72402 · 03-09-2007, 12:24 AM

Harry, headers for a 67-72 w/big block should work, the chassis are pretty much the same. Be sure to specify for a manual transmission.
I used chevelle/camaro shorty headers on my 65 with a small block and automatic, had to modify the motor mount stand a little.

harry · 03-09-2007, 02:53 AM

hi there 72402 thanks a lot for that will check it out,does the 67-72 trucks run mechanical clutch systems same as the 63

hammered65 · 03-09-2007, 07:39 PM

I used some from Sanderson. Don't remember which model, but they are supposed to be specifically for this application. They are long tubes, so they hang below the frame some. I am going to go with block huggers next time for ground clearance. The headers are well made, but Sanderson was a pain to deal with. The headers would not clear my mini starter, so they had to grind the flange, where it bolts to the head, in order to kick it out away from the starter. By the way, I am using a turbo 350, so not sure abouth manual fit. I had to notch the engine stands for clearance though.

72402 · 03-10-2007, 12:31 AM

No problem Harry, and yes, 67-72 chevy and GMC pickups had mechanical clutch linkage. Your truck's looking good by the way, and you're gonna love that big block.
Frank

**Captainfab** · 03-12-2007, 12:25 AM

The 67-72 trucks have their clutch bell crank located farther back than the 60-66 trucks. I would say that you'll need to use some block hugger headers to be able to use your stock clutch linkage. You still may have to modify it a little. When I installed a 454 in my 66 suburban, I used 73-87 headers, but I had to trim the frame to replicate the 73-87 frame, I am running a T400 also so the clutch linkage wasn't an issue. Check with Hedman Hedders for some BB block huggers, I believe they make some.

harry · 03-12-2007, 12:37 AM

thanks for that captain,i have found some block huggers that sanderson headers make and have emailed them with my clutch issue.will wait their reply
cheers karl

03-07-2007, 02:55 AM	#1
harry Registered User Join Date: Feb 2007 Location: masterton New Zealand Posts: 239	headers for 454 into 63 does any know of a bolt in header that will fit 454 into 63 and still running with the mechanical clutch system.(big block,block huggers???part#?) cheers

03-09-2007, 12:24 AM	#2
72402 Registered User Join Date: Nov 2004 Location: Cameron, Oklahoma Posts: 199	Re: headers for 454 into 63 Harry, headers for a 67-72 w/big block should work, the chassis are pretty much the same. Be sure to specify for a manual transmission. I used chevelle/camaro shorty headers on my 65 with a small block and automatic, had to modify the motor mount stand a little. __________________ 72 Cheyenne SWB Fleet/original 402, TH400, buckets & console 65 C10, 350TBI, 700R4 (work in progress)

03-09-2007, 02:53 AM	#3
harry Registered User Join Date: Feb 2007 Location: masterton New Zealand Posts: 239	Re: headers for 454 into 63 hi there 72402 thanks a lot for that will check it out,does the 67-72 trucks run mechanical clutch systems same as the 63

03-09-2007, 07:39 PM	#4
hammered65 Registered User Join Date: Jan 2007 Location: Houston Posts: 53	Re: headers for 454 into 63 I used some from Sanderson. Don't remember which model, but they are supposed to be specifically for this application. They are long tubes, so they hang below the frame some. I am going to go with block huggers next time for ground clearance. The headers are well made, but Sanderson was a pain to deal with. The headers would not clear my mini starter, so they had to grind the flange, where it bolts to the head, in order to kick it out away from the starter. By the way, I am using a turbo 350, so not sure abouth manual fit. I had to notch the engine stands for clearance though.

03-10-2007, 12:31 AM	#5
72402 Registered User Join Date: Nov 2004 Location: Cameron, Oklahoma Posts: 199	Re: headers for 454 into 63 No problem Harry, and yes, 67-72 chevy and GMC pickups had mechanical clutch linkage. Your truck's looking good by the way, and you're gonna love that big block. Frank __________________ 72 Cheyenne SWB Fleet/original 402, TH400, buckets & console 65 C10, 350TBI, 700R4 (work in progress)

03-12-2007, 12:25 AM	#6
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: headers for 454 into 63 The 67-72 trucks have their clutch bell crank located farther back than the 60-66 trucks. I would say that you'll need to use some block hugger headers to be able to use your stock clutch linkage. You still may have to modify it a little. When I installed a 454 in my 66 suburban, I used 73-87 headers, but I had to trim the frame to replicate the 73-87 frame, I am running a T400 also so the clutch linkage wasn't an issue. Check with Hedman Hedders for some BB block huggers, I believe they make some.

03-12-2007, 12:37 AM	#7
harry Registered User Join Date: Feb 2007 Location: masterton New Zealand Posts: 239	Re: headers for 454 into 63 thanks for that captain,i have found some block huggers that sanderson headers make and have emailed them with my clutch issue.will wait their reply cheers karl

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.