|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-02-2008, 06:00 AM
|
#1 |
|
Registered User
 
Join Date: Feb 2008
Location: Williamsburg, Va
Posts: 226
|
Widest wheel width on 71 fleetside
I am looking for information from others on the widest wheel you have installed on the rear. My measurements indicate I should be able to mount a 12 inch wide rim with 7 1/2 inch backspacing with 15 in wide tires but I am looking for advice before committing. Thank you
|
|
|
|
03-02-2008, 06:06 AM
|
#2 |
|
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,468
|
Re: Widest wheel width on 71 fleetside
  Is it gonna be lowered? Airbags or coil? (Airbags tend to give side to side play) I know 10" is no problem at all, for 12" you may need to widen the rear tubs.
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T Last edited by LUV2XCLR8; 03-02-2008 at 06:06 AM. |
|
|
|
|
03-02-2008, 06:08 AM
|
#3 |
|
Registered User
Join Date: Feb 2008
Location: Williamsburg, Va
Posts: 226
|
Re: Widest wheel width on 71 fleetside
That's an important question, yes I am bagging it. I already have the tubs and have cut the bed for maximum fit.
|
|
|
|
|
03-02-2008, 09:08 AM
|
#4 |
|
A guy with a truck
Join Date: Sep 2005
Location: Germany, for now
Posts: 5,921
|
Re: Widest wheel width on 71 fleetside
I was planning nearly the exact same setup. You should have room to spare if you widen the tubs to the framerails...
__________________
-Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy |
|
|
|
|
03-02-2008, 02:56 PM
|
#5 |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,068
|
Re: Widest wheel width on 71 fleetside
At one time, I had 15x14" custom back-spaced steelies w/a stock length 67/8 12-bolt truck rear (coil suspension). The bumpstop on the outside of the framerail had to go & obviously the tubs were stretched, but it required no frame modifications.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
03-03-2008, 06:53 PM
|
#6 |
|
Registered User
Join Date: Feb 2008
Location: Williamsburg, Va
Posts: 226
|
Re: Widest wheel width on 71 fleetside
Thank you for your reply
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
