Anled or straight ramhorns on 350/4 speed? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

DHregdovic · 05-19-2002, 10:30 AM

Which ramhorns do I need on my '67 setup - the straight dump or the angled dump? I will put the 350 in the 6 cyl position and the manifolds will need to clear the clutch linkage. I'm not sure but I dont think it would matter which one on the passenger side.

*Fast68Chevy* · 05-19-2002, 11:13 AM

2wd in factopry forward position use angled back, but if you set engine back in 6 spot then you may get away with straight exits. only one way to find out,.

------------------
Randy- Lincoln, IL
randy@ccaonline.com 2177353230
*many GM parts bought, traded, or sold -am parting out: '81 Cutlass Supreme and 84 SE Firebird T5 3.73

current fleet: -71 C-10 350/CH465/3.07- assembling currently
-90 Cavalier
-84 Z28
-'90 Corsica 3.1L- selling or parting out and '82 purple Trans Am- storing away *Paint is overrated* © RSS Enterprises 2000

[This message has been edited by Fast68Chevy (edited May 19, 2002).]

stllookn · 05-19-2002, 12:31 PM

My 283 appears to be the stock (aft) position and has angled on driver's side and straight down on passenger side. It's an auto.

Bobs68LWB · 05-22-2002, 09:56 AM

I put a 350 in the 6 cyl position and I used straight down ram horns on both sides. Everything fit fine.
Bob

05-19-2002, 10:30 AM	#1
DHregdovic Registered User Join Date: Jan 2002 Location: Beaver County, PA Posts: 46	Anled or straight ramhorns on 350/4 speed? Which ramhorns do I need on my '67 setup - the straight dump or the angled dump? I will put the 350 in the 6 cyl position and the manifolds will need to clear the clutch linkage. I'm not sure but I dont think it would matter which one on the passenger side. __________________ 67 LWB GMC 250 inline w/4spd manual Disc/power brake conversion

05-19-2002, 12:31 PM	#3
stllookn Saving 1 truck at a time! Join Date: Aug 2001 Location: Kent, WA Posts: 6,465	My 283 appears to be the stock (aft) position and has angled on driver's side and straight down on passenger side. It's an auto. __________________ '68 C20 Longhorn 50th Anniversary 400/TH400 '68 C20 Longhorn 50th Anniversary 468/TH400w/buckets '72 C20 Halfhorn (Longhorn w/o cab and front clip) '69 Flxible Cruiser (look up ugly in the dictionary)

05-22-2002, 09:56 AM	#4
Bobs68LWB Registered User Join Date: May 2002 Location: Beebe, AR Posts: 6	I put a 350 in the 6 cyl position and I used straight down ram horns on both sides. Everything fit fine. Bob __________________ 1968 Chevy LWB 350/700r4 373 Gears 1967 Mustang 1989 Taurus SHO 1994 Taurus 2003 Focus

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-19-2002, 11:13 AM	#2
Fast68Chevy Account Suspended Join Date: May 2000 Location: IL Posts: 0	2wd in factopry forward position use angled back, but if you set engine back in 6 spot then you may get away with straight exits. only one way to find out,. ------------------ Randy- Lincoln, IL randy@ccaonline.com 2177353230 many GM parts bought, traded, or sold -am parting out: '81 Cutlass Supreme and 84 SE Firebird T5 3.73 current fleet: -71 C-10 350/CH465/3.07- assembling currently -90 Cavalier -84 Z28 -'90 Corsica 3.1L- selling or parting out and '82 purple Trans Am- storing away Paint is overrated* © RSS Enterprises 2000 [This message has been edited by Fast68Chevy (edited May 19, 2002).]



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.