4x4 dually front axle question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Blue_71 · 04-08-2008, 07:39 AM

im looking at converting my wrecker to 4x4, so i have a couple questions about dually 4x4s...

#1 did any dually 4x4s come with a cheapy axle? im not looking to 4-wheel this thing or put huge tires in it, so a dana 44 or corp axle would be fine for some extra pulling power going through the feild as long as i could put dually wheels on it

#2 did ford make any dually 4x4s with leaf sprung straight axles? i hate like heck to put a ford axle in my truck, but at the same time my PTO output is on the passanger side, so it would be much easier to put a drivers side front driveshaft in to not have to modify any of the wrecker parts

thanks in advance!

Blazer1970 · 04-08-2008, 01:44 PM

The 4WD IFS dually trucks use a big spacer to run the Budd wheels on the normal IFS front. I think you could use these spacers with any GM 44 or 10 bolt to do what you want.

**Yukon Jack** · 04-08-2008, 05:09 PM

My buddy with the C30 converted to K30 is using a standard 3/4 ton Dana 44 with spacers to fit his dually front rims. He has had zero problems with the spacers. IIRC, he said the spacers were kinda expensive but he would have bought those probably 15 years ago I'm guessing.

**special-K** · 04-08-2008, 05:52 PM

Try www.arrowcraft.com

04-08-2008, 05:09 PM	#3
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,686	Re: 4x4 dually front axle question My buddy with the C30 converted to K30 is using a standard 3/4 ton Dana 44 with spacers to fit his dually front rims. He has had zero problems with the spacers. IIRC, he said the spacers were kinda expensive but he would have bought those probably 15 years ago I'm guessing. __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

04-08-2008, 05:52 PM	#4
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: 4x4 dually front axle question Try www.arrowcraft.com __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-08-2008, 07:39 AM	#1
Blue_71 Bloo Join Date: Feb 2001 Location: Barren County Kentucky Posts: 6,283	4x4 dually front axle question im looking at converting my wrecker to 4x4, so i have a couple questions about dually 4x4s... #1 did any dually 4x4s come with a cheapy axle? im not looking to 4-wheel this thing or put huge tires in it, so a dana 44 or corp axle would be fine for some extra pulling power going through the feild as long as i could put dually wheels on it #2 did ford make any dually 4x4s with leaf sprung straight axles? i hate like heck to put a ford axle in my truck, but at the same time my PTO output is on the passanger side, so it would be much easier to put a drivers side front driveshaft in to not have to modify any of the wrecker parts thanks in advance! Last edited by Blue_71; 04-08-2008 at 07:43 AM.

04-08-2008, 01:44 PM	#2
Blazer1970 Registered User Join Date: Dec 1999 Location: Old Mission, MI, USA Posts: 2,507	Re: 4x4 dually front axle question The 4WD IFS dually trucks use a big spacer to run the Budd wheels on the normal IFS front. I think you could use these spacers with any GM 44 or 10 bolt to do what you want. __________________ Tim



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.