Easiest way to lay rocker - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**scotts62** · 12-01-2008, 11:51 PM

Ball valves or shrader valves thats the simplest ways but if your going to bag it it wouldbe just as easy to get it overwith and do electric valves and just have a couple switches around verses valves next to the seat. As far as bags there are different kinds for different apps, our trucks would use 2600's, i have contitechs, some guys use firestones or slams with the internal bumpstops, just depends how much you are wanting to spend as far as putting airride on one.

billdo · 12-02-2008, 01:40 AM

no come on you wanna go this low. 2.5 inch z and tube back half. o and 2,5 inch drop spindles with bag pockets in the a arms.

SCOTI · 12-02-2008, 01:54 AM

Quote:

Originally Posted by scotts62

on the back you could put the bags where the coils springs go and do a c notch, front just get cups and the plates that cover coil spring pocket on bottom side of crossmember,then you just decide on what valves, tank and compressor you want to run. if your just going to have air ride the simpler way thats what i would do.

This is basically the same set-up used on N2Billets 'red' truck.
Yes, that's air'd out . . ...

FnLow69 · 12-02-2008, 01:58 AM

Quote:

Originally Posted by billdo

no come on you wanna go this low.

billdo, you know you wanna go this low... hahaha

Justin

billdo · 12-02-2008, 09:45 AM

ooo fnlow yo0ur snappy. i saw your truck before it was doored and it made me do mine i love how low yours is but i never drove my truck pulled it out iof the woods and im at the point where i wanann drive it and doin what you did is more time besides i still have body work and motor. and a drive shaft night maree lol but it is beautifull i lopve your truck got any progress

**scotts62** · 12-02-2008, 11:18 AM

uh oh some competition, next we'll see a truck with half the doors setting on the ground

Looks good guys!

FnLow69 · 12-02-2008, 11:41 AM

not any progress in a while.... i hope to work on it soon.

**scotts62** · 12-02-2008, 01:08 PM

Yeah same here been working a lot and with all the holiday stuff going on right now it will be a bit.

Spray-Bomb · 12-02-2008, 02:45 PM

Ooooo, I hate you both !!! J/K

I just cant afford the time & money to go any lower

**scotts62** · 12-02-2008, 05:05 PM

I can't either at the moment, plus if i do get lower ill probably have scrap metal all over the highway if something stupid happens so ill just stay where im at now

12-01-2008, 11:51 PM	#26
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,243	Re: Easiest way to lay rocker Ball valves or shrader valves thats the simplest ways but if your going to bag it it wouldbe just as easy to get it overwith and do electric valves and just have a couple switches around verses valves next to the seat. As far as bags there are different kinds for different apps, our trucks would use 2600's, i have contitechs, some guys use firestones or slams with the internal bumpstops, just depends how much you are wanting to spend as far as putting airride on one. __________________ Scott 93 crew cab build Project 62

12-02-2008, 01:40 AM	#27
billdo Registered User Join Date: Oct 2007 Location: hopewell jct new york Posts: 140	Re: Easiest way to lay rocker no come on you wanna go this low. 2.5 inch z and tube back half. o and 2,5 inch drop spindles with bag pockets in the a arms. Last edited by billdo; 12-02-2008 at 01:41 AM.

12-02-2008, 09:45 AM	#30
billdo Registered User Join Date: Oct 2007 Location: hopewell jct new york Posts: 140	Re: Easiest way to lay rocker ooo fnlow yo0ur snappy. i saw your truck before it was doored and it made me do mine i love how low yours is but i never drove my truck pulled it out iof the woods and im at the point where i wanann drive it and doin what you did is more time besides i still have body work and motor. and a drive shaft night maree lol but it is beautifull i lopve your truck got any progress

12-02-2008, 11:18 AM	#31
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,243	Re: Easiest way to lay rocker uh oh some competition, next we'll see a truck with half the doors setting on the ground Looks good guys! __________________ Scott 93 crew cab build Project 62

12-02-2008, 11:41 AM	#32
FnLow69 Registered User Join Date: May 2005 Location: Washington Posts: 848	Re: Easiest way to lay rocker not any progress in a while.... i hope to work on it soon. __________________ [PROJECT] FnLow69- 69 C-10 Full frame & layin' doors [PROJECT] Laidout53 - 53' Dodge Pickup, Full Kustom Build [PROJECT] "Hot Rod" 1931 Model A Bonneville style "Dream as if you'll live forever, Live as if you'll die today" ~ James Dean

12-02-2008, 01:08 PM	#33
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,243	Re: Easiest way to lay rocker Yeah same here been working a lot and with all the holiday stuff going on right now it will be a bit. __________________ Scott 93 crew cab build Project 62

12-02-2008, 02:45 PM	#34
Spray-Bomb Texas Big Wig Join Date: Jan 2007 Location: Mineola, Texas Posts: 5,620	Re: Easiest way to lay rocker Ooooo, I hate you both !!! J/K I just cant afford the time & money to go any lower __________________ Just not low enough... ----------------------------- Sinister Killer

12-02-2008, 05:05 PM	#35
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,243	Re: Easiest way to lay rocker I can't either at the moment, plus if i do get lower ill probably have scrap metal all over the highway if something stupid happens so ill just stay where im at now __________________ Scott 93 crew cab build Project 62

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.