Tell me what YOU think... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Project82 · 01-27-2009, 07:27 PM

Just put my new AERO 52 series wheels on my 82, reusing my old 235/70/r15s...

what do you think i should do next? I debating whether or not to lower it some more...maybe like 3 more inches all around...right now it has one coil cut off of new springs up front, and homemade 2 inch shackles for the rear with the overload springs removed...i think it has a 2/4 or 2/3...

Summit Racing (same place i ordered my wheels from) has 3 inch drop spindles for about $282 a pair, maybe those plus a homemade flip kit for the rear..another question i have is since my wheels are 15's...will i still be able use a 3" drop spindle...or do i need to go with something else to lower it?

EyeH8the24 · 01-27-2009, 08:38 PM

has that nascar look !

spr85gmc · 01-27-2009, 08:50 PM

slam it already 5/5...5/6

**Dads79GMC** · 01-27-2009, 08:51 PM

Leave it be.

spr85gmc · 01-27-2009, 08:52 PM

Quote:

Originally Posted by Dads79GMC

Leave it be.

he's lying he really means to lower it...

EyeH8the24 · 01-27-2009, 09:13 PM

agrees with lowering it ......do it !

Project82 · 01-27-2009, 09:25 PM

Thanks guys. I think im going to end up lowering it...but before i do that...i need to do a lot of research...especially if i might not be able to use these wheels with dropped spindles...

Before i drop it some more i really need to clean out the dual tanks and replace the sending units and all the fuel lines...it has a sputtering problem if i give it too much gas after 2nd gear...and, because the sending units have never been replaced...

1984 swb chevy · 01-27-2009, 09:28 PM

looks good you should lower it.

brad2 · 01-28-2009, 12:40 AM

Generally you will have to trim your lower control arm when you use three inch spindles with 15 inch wheels.

**N2TRUX** · 01-28-2009, 01:20 AM

Lower it, get some lower profile tires, then have some pinstripe flames put on it in the same color is the wheel stripe...

**N2TRUX** · 01-28-2009, 01:27 AM

Like this-

Hoods69BadBowTie · 01-28-2009, 03:55 AM

I like it I would lower it more though and do something that matches the wheel stripe for sure

heavychevy79 · 01-28-2009, 04:08 AM

Quote:

Originally Posted by brad2

Generally you will have to trim your lower control arm when you use three inch spindles with 15 inch wheels.

I didn't have to, what spindles did you use?

Ds86C10 · 01-28-2009, 06:50 AM

Quote:

Originally Posted by heavychevy79

I didn't have to, what spindles did you use?

like he said GENERALLY with 3 inch drop spindles you need to trim the control arms... it doesnt matter what brand they are its hit or miss....

I say lower it a little bit more. 2.5 inch drop spindles you shouldnt have any problems

Cherub · 01-28-2009, 09:14 AM

I have a 6/6 drop on my truck. 3" drop spindle and 3" drop spring from djm. If you want to come on by we can see if your rims will fit. To me thats the only way of knowing forsure, throw them on and see what happens.

Insane72Bowtie · 01-28-2009, 11:28 PM

Just lower the back alittle and level it up with the front......

enaberif · 01-28-2009, 11:52 PM

not my cup of tea.. but hey if you like it.. rock on.

Rollie396 · 01-29-2009, 12:16 AM

First get it running the way you want it.Get that 383 mentioned in your sig in it,then worry about stance,looks yada yada.If that's out of the question,then I'd say tuck the tread and level it a bit.

Square84 · 01-29-2009, 12:54 AM

Quote:

Originally Posted by n2trux

like this-

i also say slam it and off topic have ya'll seen this truck in this month's truckin its badass now that its all blacked out.

Trick76 · 01-29-2009, 01:01 AM

Forget lowering for now, build a hot motor and do a SWB conversion with some duals exiting out in front of the rear wheels

Project82 · 02-03-2009, 11:37 PM

Thanks for all your input guys! i really appreciate it!

But i think i have A LOT of thinking to do...especially if i want to goto Wyotech after i graduate from high school...

...all though i really would like a beasty small block to whoop some of my import trash talking friends' a$$'s!

maxreps · 02-04-2009, 09:56 AM

Quote:

Originally Posted by Insane72Bowtie

Just lower the back alittle and level it up with the front......

I agree with this...

01-27-2009, 07:27 PM	#1
Project82 Bretzke Racing Inc. Join Date: Jun 2008 Location: Houston, Texas Posts: 114	Tell me what YOU think... Just put my new AERO 52 series wheels on my 82, reusing my old 235/70/r15s... what do you think i should do next? I debating whether or not to lower it some more...maybe like 3 more inches all around...right now it has one coil cut off of new springs up front, and homemade 2 inch shackles for the rear with the overload springs removed...i think it has a 2/4 or 2/3... Summit Racing (same place i ordered my wheels from) has 3 inch drop spindles for about $282 a pair, maybe those plus a homemade flip kit for the rear..another question i have is since my wheels are 15's...will i still be able use a 3" drop spindle...or do i need to go with something else to lower it? Attached Images __________________ 1982 Chevy Silverado C-10 RCLWB - IN PAINT - Inferno Orange Metallic Lowered 4.5/6 - 358 SBC 10.5:1, Comp XE268H cam, Aluminum heads, 650 Double pumper Holley carb, 2400 Holeshot Converter, upgraded T/h350 Trans. Stock Rear end for now (3.08 gear) 2004 Chevy Silverado 1500 LS RCSWB - Dark Spiral Gray Metallic Lowered 2/4 - 4.8L V8 4L60E 10-bolt. some goodies --- NEW DD 11/9/12 "Expect the Un-expected" "Gas, Grass, Or Ass...No one rides for FREE!"

01-27-2009, 08:38 PM	#2
EyeH8the24 Registered User Join Date: Dec 2004 Location: beulah,alabama Posts: 1,075	Re: Tell me what YOU think... has that nascar look !

01-27-2009, 08:50 PM	#3
spr85gmc Registered User Join Date: Jul 2007 Location: san antonio Posts: 648	Re: Tell me what YOU think... slam it already 5/5...5/6

01-27-2009, 08:51 PM	#4
Dads79GMC Senior Member Join Date: Feb 2008 Location: Des Moines, Iowa Posts: 1,238	Re: Tell me what YOU think... Leave it be. __________________ Instagram @HomeBuiltC10s Dads 79 GMC Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=642929 1978 Silverado Build http://67-72chevytrucks.com/vboard/s...d.php?t=756016

01-27-2009, 09:13 PM	#6
EyeH8the24 Registered User Join Date: Dec 2004 Location: beulah,alabama Posts: 1,075	Re: Tell me what YOU think... agrees with lowering it ......do it !

01-27-2009, 09:25 PM	#7
Project82 Bretzke Racing Inc. Join Date: Jun 2008 Location: Houston, Texas Posts: 114	Re: Tell me what YOU think... Thanks guys. I think im going to end up lowering it...but before i do that...i need to do a lot of research...especially if i might not be able to use these wheels with dropped spindles... Before i drop it some more i really need to clean out the dual tanks and replace the sending units and all the fuel lines...it has a sputtering problem if i give it too much gas after 2nd gear...and, because the sending units have never been replaced... __________________ 1982 Chevy Silverado C-10 RCLWB - IN PAINT - Inferno Orange Metallic Lowered 4.5/6 - 358 SBC 10.5:1, Comp XE268H cam, Aluminum heads, 650 Double pumper Holley carb, 2400 Holeshot Converter, upgraded T/h350 Trans. Stock Rear end for now (3.08 gear) 2004 Chevy Silverado 1500 LS RCSWB - Dark Spiral Gray Metallic Lowered 2/4 - 4.8L V8 4L60E 10-bolt. some goodies --- NEW DD 11/9/12 "Expect the Un-expected" "Gas, Grass, Or Ass...No one rides for FREE!"

01-27-2009, 09:28 PM	#8
1984 swb chevy Registered User Join Date: Nov 2007 Location: New Jersey Posts: 466	Re: Tell me what YOU think... looks good you should lower it. __________________ 2010 Tahoe 1984 C10 2005 Harley FLH 1941 Willys Pickup (will never get it done) not for sale

01-28-2009, 12:40 AM	#9
brad2 Registered User Join Date: Feb 2001 Location: edmond, ok Posts: 1,056	Re: Tell me what YOU think... Generally you will have to trim your lower control arm when you use three inch spindles with 15 inch wheels. __________________ 74 swb 71 2wd Jimmy 82 2wd Blazer

01-28-2009, 01:20 AM	#10
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: Tell me what YOU think... Lower it, get some lower profile tires, then have some pinstripe flames put on it in the same color is the wheel stripe... __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" Last edited by N2TRUX; 01-28-2009 at 01:21 AM.

01-28-2009, 01:27 AM	#11
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: Tell me what YOU think... Like this- __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

01-28-2009, 03:55 AM	#12
Hoods69BadBowTie Chevys Kick A$$ Join Date: Jan 2005 Location: Zootown, MT Posts: 12,699	Re: Tell me what YOU think... I like it I would lower it more though and do something that matches the wheel stripe for sure __________________ HOODS is what I answer too -'79, '77, '88 Pickup Sold, '85 Camaro, '83 T/A, '81,'83,'90 K5 Blazer All Sold -'79 3/4 ton "Big Yellow Bananna" Lifted 4spd. 39.5 TSL Swampers, The money Pit -'86 K5 Blazer Silverado 6.2 4" lift 35"s -'95 Ext. Cab Shorty 4" Tuff Country rolling 35" M/T's -'83 Monte Carlo T-Tops. 126,500 Original Miles -LATER I would rather push a Chevy then drive a ford!!

01-28-2009, 09:14 AM	#15
Cherub Registered User Join Date: Feb 2008 Location: Houston Posts: 970	Re: Tell me what YOU think... I have a 6/6 drop on my truck. 3" drop spindle and 3" drop spring from djm. If you want to come on by we can see if your rims will fit. To me thats the only way of knowing forsure, throw them on and see what happens. Last edited by Cherub; 01-28-2009 at 09:16 AM.

01-28-2009, 11:28 PM	#16
Insane72Bowtie Registered User Join Date: Mar 2008 Location: St. Francis Kansas Posts: 26	Re: Tell me what YOU think... Just lower the back alittle and level it up with the front...... __________________ Snap On Tools Dirt Racing PeterBilt And Chevrolets!

01-28-2009, 11:52 PM	#17
enaberif Registered User Join Date: Jan 2009 Location: Calgary, AB Posts: 1,181	Re: Tell me what YOU think... not my cup of tea.. but hey if you like it.. rock on.

01-29-2009, 12:16 AM	#18
Rollie396 someday it will be done! Join Date: Sep 2004 Location: Lloydminster,AB. Canada Posts: 1,620	Re: Tell me what YOU think... First get it running the way you want it.Get that 383 mentioned in your sig in it,then worry about stance,looks yada yada.If that's out of the question,then I'd say tuck the tread and level it a bit. __________________ '72 C-10 Proud owner of a million new and used pieces that used to be and will once again be(god willing) a testament to the term "they don't build em like that anymore. '80 LWB 2wd beater '67 GMC long fleet (cab donor) '66 long step (parked till it's turn comes around) '65 short step (parts truck that will donate it's bed and possibly frame to the '66) '06 Grand Prix wife's car (she hardly lets me touch it) my pics



Register or Log In To remove these advertisements.

01-29-2009, 01:01 AM	#20
Trick76 Living la vida broka Join Date: Jan 2003 Location: P'ville California Posts: 221	Re: Tell me what YOU think... Forget lowering for now, build a hot motor and do a SWB conversion with some duals exiting out in front of the rear wheels __________________ 1976 C10 Longbed lowered 5/7, hot 355/TH350. ~ SOLD 1974 C10 Shortbed Stepside 350/Saginaw ~ SOLD 1984 C10 Longbed 6.2l diesel 700r4. ~SOLD 1985 GMC C20 350 700r4, ~under the knife

02-03-2009, 11:37 PM	#21
Project82 Bretzke Racing Inc. Join Date: Jun 2008 Location: Houston, Texas Posts: 114	Re: Tell me what YOU think... Thanks for all your input guys! i really appreciate it! But i think i have A LOT of thinking to do...especially if i want to goto Wyotech after i graduate from high school... ...all though i really would like a beasty small block to whoop some of my import trash talking friends' a$$'s! __________________ 1982 Chevy Silverado C-10 RCLWB - IN PAINT - Inferno Orange Metallic Lowered 4.5/6 - 358 SBC 10.5:1, Comp XE268H cam, Aluminum heads, 650 Double pumper Holley carb, 2400 Holeshot Converter, upgraded T/h350 Trans. Stock Rear end for now (3.08 gear) 2004 Chevy Silverado 1500 LS RCSWB - Dark Spiral Gray Metallic Lowered 2/4 - 4.8L V8 4L60E 10-bolt. some goodies --- NEW DD 11/9/12 "Expect the Un-expected" "Gas, Grass, Or Ass...No one rides for FREE!"

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.