The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-21-2009, 08:57 AM   #1
chucks1967
Registered User
 
Join Date: May 2008
Location: athens alabama
Posts: 93
I need some openions

I have a good bed shell, but the inner panels where the bed floor mounts to is all rusted out and gone, as are the wheel well lip at the bottom.. What are my options. I know about mar-k and there replacement panels and wheel well lips, but I am short of cash as every one is these days. What would you do. I have plenty of sheet metal... should I make my own lip? or should I just bite the bullet and get the replacement panels prefabbed up. the rust doesn't extend very far up the panel. Basically it just rusted out at the 90 deg bend. Opinions would be much appreciated.
Thanks in advance.
chucks1967 is offline   Reply With Quote
Old 08-21-2009, 09:06 AM   #2
Bears63
...just another truck junkie..
 
Bears63's Avatar
 
Join Date: May 2009
Location: Watertown, SD
Posts: 698
Re: I need some openions

If it was me I would try my hand at fabbing something up myself first. If you have plenty of sheet metal, then you have a little room for trial and error. If it doesn't work out then you can rethink your options. Basically, what will it cost you to try and fab up your own pieces? If the cost of time and material is lower than buying panels, then go for it. Besides, it's an opportunity to do something else yourself, to be able to point it out and say "Hey, I fixed that!"

Just my $0.02
__________________
Mike "Bear" Shea
Bears63 is offline   Reply With Quote
Old 08-21-2009, 09:44 AM   #3
jason65
Registerd User
 
jason65's Avatar
 
Join Date: Sep 2008
Location: Oklahoma
Posts: 2,118
Re: I need some openions

If you made your own how would you make square holes for the carage bolts? Just drill out the holes and bolt the carage bolts up to make the holes square?
jason65 is offline   Reply With Quote
Old 08-21-2009, 09:45 AM   #4
MacAttack
283 Drama Queen
 
MacAttack's Avatar
 
Join Date: Dec 2004
Location: Surf City, CA
Posts: 2,435
Re: I need some openions

^^x2 Gotta' go with Mike on this one - what have you got to lose?

Mac.
__________________
For about 12 years of my adult life I had a severe speech impediment.
My ex-wife never let me get a word in edgewise.
MacAttack is offline   Reply With Quote
Old 08-21-2009, 10:03 AM   #5
padresag
Registered User
 
Join Date: Feb 2008
Location: Sidney,b.c.
Posts: 4,425
Re: I need some openions

Quote:
Originally Posted by jason65 View Post
If you made your own how would you make square holes for the carage bolts? Just drill out the holes and bolt the carage bolts up to make the holes square?
just drill the round holes and a jig saw with a metal blade to square it up for one way
ron
padresag is offline   Reply With Quote
Old 08-24-2009, 10:40 AM   #6
chucks1967
Registered User
 
Join Date: May 2008
Location: athens alabama
Posts: 93
Re: I need some openions

The hole issue was one that was holding me up.. I was thinking about just drilling the hole a tad bit smaller than the edge on the square carriage bolt, then when I tighten it up it would draw the bold down. I wonder if anyone else has tried this? and how well it would work.. or would it just bend up the lip..
chucks1967 is offline   Reply With Quote
Old 08-24-2009, 01:02 PM   #7
padresag
Registered User
 
Join Date: Feb 2008
Location: Sidney,b.c.
Posts: 4,425
Re: I need some openions

there are places that let you demonstrate putting square things in round holes. there is more than likely a sheet metal place around somewhere that can punch them out for you.
how much more work is it really to cut them out?
ron
padresag is offline   Reply With Quote
Old 08-24-2009, 10:49 PM   #8
chucks1967
Registered User
 
Join Date: May 2008
Location: athens alabama
Posts: 93
Re: I need some openions

Thanks for all the opinions. I have been looking for a square punch but no luck. There are not many sheet metal shops around here, and the one that are don't do much with anything over 22 gauge. But the jigsaw idea may work.
chucks1967 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:49 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com