The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1969 - 1972 Blazers and Jimmys Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-01-2010, 08:01 PM   #1
mrjones0
Registered User
 
Join Date: Feb 2010
Location: galena md
Posts: 12
1971 Jimmy 3 Speed

I just acquired a 1971 GMC Jimmy with the 3 on the tree. I was wondering if anyone knew how common they were? In searching I have only found one other blazer/jimmy with the three on the tree. I know they made more then 2 but I was wondering if anyone knew how many with the 3 on the tree and the 307. I know this was the standard engine trans combo didnt know if they made too many of them.
mrjones0 is offline   Reply With Quote
Old 02-02-2010, 10:55 AM   #2
Yukon Jack
Post Whore
 
Yukon Jack's Avatar
 
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,686
Re: 1971 Jimmy 3 Speed

Welcome to the board. Any pics of your 71? I don't recall seeing very many three on the tree Jimmy's or K5's on this board or many with the 307, but I do seem to recall a past post on the subject of the three on the tree. My 70 had the SM465 with the Dana 20 transfer case originally.
__________________
1970 Blazer with a 400 sbc and 4" lift
1980 Pontiac Trans Am, 455 Oldsmobile
2012 Kawasaki Concours 14
Yukon Jack is offline   Reply With Quote
Old 02-02-2010, 02:30 PM   #3
pound41
Registered User
 
Join Date: Dec 2002
Location: Northern Virginia
Posts: 1,268
Re: 1971 Jimmy 3 Speed

i have seen two of them here in northern virginia but that was a long ago time and i haven't seen theme in years
pound41 is offline   Reply With Quote
Old 02-02-2010, 02:49 PM   #4
mrjones0
Registered User
 
Join Date: Feb 2010
Location: galena md
Posts: 12
Re: 1971 Jimmy 3 Speed

here are some pictures they are the ones that the guy sent me before I bought it. it is in rough shape but I figured I could use a project this is my first auto purchase. I am 20 and at college now itching to get working on it. It does turn over and should run but we will see. The drivers side floorboard is rusted through rockers and such. It needs a tailgate and needs rear quarters repaired. The tub is rusty it originally had a snow plow on it from the dealer and lived in west virginia. That explains the rust.
Attached Images
    
mrjones0 is offline   Reply With Quote
Old 02-02-2010, 03:09 PM   #5
pound41
Registered User
 
Join Date: Dec 2002
Location: Northern Virginia
Posts: 1,268
Re: 1971 Jimmy 3 Speed

That looks just like the one from here in Northern Va it had a plow on it as well. Which I laughed about to myself about having the 307 and the 3 on the tree with a plow. Since 3 on the trees can be very tempremental.
pound41 is offline   Reply With Quote
Old 02-02-2010, 03:37 PM   #6
mrjones0
Registered User
 
Join Date: Feb 2010
Location: galena md
Posts: 12
Re: 1971 Jimmy 3 Speed

yeah i think thats a little amusing too the three on the tree and a plow. does anybody know if the floorboards from a 67-72 pickup are the same as in the jimmy/blazer
mrjones0 is offline   Reply With Quote
Old 02-02-2010, 03:46 PM   #7
pound41
Registered User
 
Join Date: Dec 2002
Location: Northern Virginia
Posts: 1,268
Re: 1971 Jimmy 3 Speed

The seat brackets that are welded to the pan for bench versus bucket are different. They are the same until you get to the b pillar then the truck is longer like where the gas tank on a truck sits the blazer floor pan mounts to the knee wall. I think some of the supports are different. I am in the process of doing it. about 80% of my floors are being replaced with a combo of a truck floor pan from AZ and patches. They now make a complete truck pan that needs a little altering. There are lots of treads that you can see. Jaros, VT Blazer Big J there are several great threads Good Luck
pound41 is offline   Reply With Quote
Old 02-02-2010, 05:55 PM   #8
mrjones0
Registered User
 
Join Date: Feb 2010
Location: galena md
Posts: 12
Re: 1971 Jimmy 3 Speed

thanks i saw the complete pans from lmc and didnt think the truck and blazer/jimmy would be to different on the front floor pan. this also might be a dumb question but on the back the floor is the same as a bed on a truck right?
mrjones0 is offline   Reply With Quote
Old 02-02-2010, 06:28 PM   #9
pound41
Registered User
 
Join Date: Dec 2002
Location: Northern Virginia
Posts: 1,268
Re: 1971 Jimmy 3 Speed

Yes the back is the same as a pickup a short bed is the same except for its a little longer up front. Check out those build threads you will find everything you need
pound41 is offline   Reply With Quote
Old 02-03-2010, 12:57 AM   #10
jaros44sr
Senior Member
 
jaros44sr's Avatar
 
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,762
Re: 1971 Jimmy 3 Speed

Quote:
Originally Posted by pound41 View Post
The seat brackets that are welded to the pan for bench versus bucket are different. They are the same until you get to the b pillar then the truck is longer like where the gas tank on a truck sits the blazer floor pan mounts to the knee wall. I think some of the supports are different. I am in the process of doing it. about 80% of my floors are being replaced with a combo of a truck floor pan from AZ and patches. They now make a complete truck pan that needs a little altering. There are lots of treads that you can see. Jaros, VT Blazer Big J there are several great threads Good Luck
Thank you for the kind words, you put in very fine company
__________________
Semper Fi...Uncle Sam, you da man

All parts offered to help are free, unless otherwise noted

Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training
SAFETY FIRST

AS usual, off topic

They say your mind goes second, can't remember the first


Jim
jaros44sr is online now   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:25 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com