need measurements - The 1947 - Present Chevrolet & GMC Truck Message Board Network

hotrod386 · 03-02-2010, 02:33 AM

i`m looking at a `53 chevy pickup shortbed and have no place to put it right now does anyone have measurements from bumper to bumper and without the bumper and how wide. i hope to rent a shed till i can make room. thanks for the help

OrrieG · 03-02-2010, 01:03 PM

Look at this site, bookmark the link it is hard to navigate thru the site to find it. Scroll down to the tech manual for your series, tons of cool information and dimensions not found in the assembly manuals.

http://www.tocmp.com/tOCMP/chevy.tocmp.com/

63 & 64 Bowties · 03-02-2010, 01:09 PM

Since my 53 is in pieces right now, this is just an approximate figure:
72" x 192"
The width should be accurate because my bed is still assembled. And, I'd say I'm within a couple inches of the length. That figure is with both bumpers on. You'll probably be about a foot shorter with the bumpers removed.
Hope that helps.
And, don't forget we'll need pictures when you get it.

Steve@OldSub.com · 03-02-2010, 02:50 PM

Quote:

Originally Posted by 63 & 64 Bowties

Since my 53 is in pieces right now, this is just an approximate figure: 72" x 192"

I measured my Suburban just an hour ago wondering if I can squeese it into my shop. It is 72 inches wide and including front and rear bumpers 198 inches long or six feet wide by sixteen and a half feet long.

My measurements assumed I'd fold the mirrors in or let them hang over something, if you need to account for mirrors too you may need to measure them because they vary so much in style and width.

hotrod386 · 03-02-2010, 05:37 PM

thanks everybody ya`ll been very helpful. to bad for me i`m just going to have to wait on this truck. the shed is only 10X12X8 theres about a 4 foot difference. thanks again

winchster · 03-02-2010, 07:22 PM

Quote:

Originally Posted by OrrieG

Look at this site, bookmark the link it is hard to navigate thru the site to find it. Scroll down to the tech manual for your series, tons of cool information and dimensions not found in the assembly manuals.

http://www.tocmp.com/tOCMP/chevy.tocmp.com/

Orrie, you have the updated links from this site. When I click on nearly anything to do with our truck series, AD, the information is not found.

OrrieG · 03-02-2010, 11:29 PM

Here is where it is: See if this helps.

http://chevy.oldcarmanualproject.com...esto/index.htm

Scroll down and click on the section that says "Specification Information (Resto-Packs) Packages - Pre 1960"

Here is the specific page that shows 53 truck dimensions:

http://chevy.oldcarmanualproject.com...esto/53060.htm

Here is the picture on that page:

winchster · 03-02-2010, 11:57 PM

Thanks Orrie

03-02-2010, 02:33 AM	#1
hotrod386 Registered User Join Date: Mar 2009 Location: wood river il. Posts: 15	need measurements i`m looking at a `53 chevy pickup shortbed and have no place to put it right now does anyone have measurements from bumper to bumper and without the bumper and how wide. i hope to rent a shed till i can make room. thanks for the help

03-02-2010, 01:03 PM	#2
OrrieG Registered User Join Date: Jun 2006 Location: Idaho Posts: 8,800	Re: need measurements Look at this site, bookmark the link it is hard to navigate thru the site to find it. Scroll down to the tech manual for your series, tons of cool information and dimensions not found in the assembly manuals. http://www.tocmp.com/tOCMP/chevy.tocmp.com/ __________________ 1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project

03-02-2010, 01:09 PM	#3
63 & 64 Bowties and a few others Join Date: Jun 2007 Location: Blue Ridge Mountains of VA Posts: 5,638	Re: need measurements Since my 53 is in pieces right now, this is just an approximate figure: 72" x 192" The width should be accurate because my bed is still assembled. And, I'd say I'm within a couple inches of the length. That figure is with both bumpers on. You'll probably be about a foot shorter with the bumpers removed. Hope that helps. And, don't forget we'll need pictures when you get it. __________________ Bill US Army Vet -193rd Infantry BlueRidgeMuscleCars.com “The greatness of a nation and its moral progress can be judged by the way its animals are treated” Gandhi

03-02-2010, 05:37 PM	#5
hotrod386 Registered User Join Date: Mar 2009 Location: wood river il. Posts: 15	Re: need measurements thanks everybody ya`ll been very helpful. to bad for me i`m just going to have to wait on this truck. the shed is only 10X12X8 theres about a 4 foot difference. thanks again

03-02-2010, 11:29 PM	#7
OrrieG Registered User Join Date: Jun 2006 Location: Idaho Posts: 8,800	Re: need measurements Here is where it is: See if this helps. http://chevy.oldcarmanualproject.com...esto/index.htm Scroll down and click on the section that says "Specification Information (Resto-Packs) Packages - Pre 1960" Here is the specific page that shows 53 truck dimensions: http://chevy.oldcarmanualproject.com...esto/53060.htm Here is the picture on that page: Attached Images __________________ 1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project

03-02-2010, 11:57 PM	#8
winchster Registered User Join Date: Jul 2006 Location: Fort Worth, TX Posts: 220	Re: need measurements Thanks Orrie __________________ '49 AD 5 window deluxe cab sitting on a '78 K5 chassis Support our troops, stand behind 'em or get in front of 'em. What country can preserve its liberties if its rulers are not warned from time to time that their people preserve the spirit of resistance?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.