Which motor mounts set the motor back the most? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

chevydog66 · 08-12-2010, 11:37 AM

I had the ECE mounts, now I have the Car Shop mounts, havent installed motor yet with new mounts, but it looks like they might set the motor even more forward than the ECE mounts. So which mounts would set the motor back the most?

team39763 · 08-12-2010, 11:42 AM

Have you tried the 1" setback mounts that carshopinc makes? I had their regular mounts, but switched to another brand's 1" setback since carshopinc didn't make them at the time. It set my motor exactly where the old sbc used to be and my trans bolted right up.

chevydog66 · 08-12-2010, 11:44 AM

Quote:

Originally Posted by team39763

Have you tried the 1" setback mounts that carshopinc makes? I had their regular mounts, but switched to another brand's 1" setback since carshopinc didn't make them at the time. It set my motor exactly where the old sbc used to be and my trans bolted right up.

I didn't know they had 1" setback mounts. I just received CSP 2349 mounts yesterday, will try to reinstall tonight. Thanks!

chevydog66 · 08-12-2010, 11:50 AM

Dangit, if I would have known about those CSP 2370, I would have ordered them instead. Thanks for the info Team39763!

glock35ipsc · 08-12-2010, 09:58 PM

#2 and #3 are the most common plates.

chevydog66 · 08-13-2010, 12:26 AM

Ok, ya so now I'm mad. I had the ECE mounts but sold them because the mounts were about 1" too far forward, now I have the Car Shop CSP 2349 mounts and its even worse. I want a LS motor mount that I will be able to use the LS clutch fan and the original 72 fan shroud, and the bellhousing flange meet up the trans. that is in the truck. Any suggestions? Thanks for the diagram Glock, I can visually see what I need now, who makes or sells the # 1's? I think that is what I need. Thinking about returning my 2349 for the 2370.

glock35ipsc · 08-14-2010, 12:12 PM

No one makes #1 commercially that I am aware of. Someone might, but I just haven't seen them. I just included it in my diagram for the engine mount sticky. If those are the ones you need, they are super simple to make.

These would be the closest:

http://tpiparts.net/inc/sdetail/16936

chevydog66 · 08-15-2010, 01:48 PM

Thanks again Glock, you da man, I looked at those and considered them at first.

**Clyde65** · 08-16-2010, 11:26 AM

I used the POL stands, on the rear mounting holes and then used their mount plates too. I could use the shroud with a little trimmin.

chevydog66 · 08-16-2010, 11:31 AM

I just ordered the tpiparts plates, shipped express, and will be returning my Car shop mounts. Hopefully I will be putting it in for the last time tomorrow.

c10seconds · 08-16-2010, 12:32 PM

Let us know how it sits. I may have to order some of those as well

team39763 · 08-20-2010, 11:23 AM

Mine sorta look like the ones in #1. I couldn't get a real good look at them since my hood is stuck. I believe mine are the S&P 1" setback mounts. Shortly after I bought mine to replace my standard carshopinc mounts, carshopinc started making 1" setback mounts.

chevydog66 · 08-20-2010, 11:30 AM

Quote:

Originally Posted by c10seconds

Let us know how it sits. I may have to order some of those as well

They fit good. a little thick though, about 3/8" thick. I had to slot my engine stands and the frame in order to get the motor to set down on the stands with the adapters and Prothane mounts. I used them in the most forward position, so that I could use the LS fan and 72 shroud, but now I can't mount my a/c compressor in Ls fashion. With the ECE mounts I could use the LS a/c compressor in it's normal location, but the Ls fan was real close to the radiator. Had to notch the bottom of shroud to clear water pump snout, and install fan and shroud as 1.

eagleuh1 · 08-23-2010, 12:15 AM

Have you tried using 6 cyl stands in rear position with the # 2 plates. This is what I used. Engine sits back pretty good.

chevydog66 · 08-24-2010, 02:50 PM

Quote:

Originally Posted by eagleuh1

Have you tried using 6 cyl stands in rear position with the # 2 plates. This is what I used. Engine sits back pretty good.

Nope haven't tried that. I was able to slot stands and frame and it sets back good. Still able to use Ls fan and 72 shroud, but a/c compressor doesn't fit in stock location. Oh well I guess we can't have it all.

joejbal · 08-28-2010, 10:19 PM

I agree, I used the 6 cyl stands with plates like number two, and a urethan version of the stock type mount. the engine sits very close to the firewall, like it was meant to go there.

usmcchevy · 09-10-2010, 04:14 PM

Quote:

Originally Posted by joejbal

I agree, I used the 6 cyl stands with plates like number two, and a urethan version of the stock type mount. the engine sits very close to the firewall, like it was meant to go there.

Does the AC comp fit in there with the motor mounted like this?

chevydog66 · 09-10-2010, 08:57 PM

Mine doesn't. I think I will have to go with the high mount bracket.

eagleuh1 · 09-11-2010, 07:28 AM

Mine does but I made my own compressor mount to move the AC in closer to the engine. No good pics available. Wish had taken some before engine install. I got some compressor blocks from Docs Blocks.com. Have put on yet.

68GMCCustom · 09-20-2010, 07:44 PM

I'm hoping someone here can help. I too had the ECE mounts and found them to mount the motor too far forward and am now using some Transdapt mounts that are similar to #1.

My question is.....now that I have the motor so much further back...will I still be able to get the cab on?

68GMCCustom · 09-20-2010, 07:51 PM

Mine is using 6cyl mounts and the rear holes...plus the mounts look like the set back further....too far back?

chevydog66 · 09-20-2010, 09:14 PM

Quote:

Originally Posted by 68GMCCustom

Mine is using 6cyl mounts and the rear holes...plus the mounts look like the set back further....too far back?

That's my pic.

68GMCCustom · 09-21-2010, 10:46 AM

well duh.

I was using your pic for comparison.... because I didn't have any of mine...now I do...here's mine:

68GMCCustom · 09-21-2010, 09:54 PM

I guess the more I look....the motor mount looks to be in the same location on the motor plate as yours chevydog?

chevydog66 · 09-21-2010, 11:01 PM

Quote:

Originally Posted by 68GMCCustom

I guess the more I look....the motor mount looks to be in the same location on the motor plate as yours chevydog?

Yep, it's just that you have your towers in the most rear holes. I have mine in the front 2 holes on the frame.

08-12-2010, 11:50 AM	#4
chevydog66 GM ONLY BABY!!! Join Date: Oct 2003 Location: Fort Wayne, IN. Posts: 1,998	Re: Which motor mounts set the motor back the most? Dangit, if I would have known about those CSP 2370, I would have ordered them instead. Thanks for the info Team39763! __________________ 2 wrongs don't make a right, but 3 lefts do. 66 Chevelle Malibu 406ci, 573hp, 10.99@121mph 96 Chevy Silverado Z71 72 GMC 1500 Super Custom LS 6.0/4L65 on airride http://www.cardomain.com/ride/707879...mc-c-k-pick-up Last edited by chevydog66; 08-12-2010 at 11:51 AM.

08-12-2010, 09:58 PM	#5
glock35ipsc Next project: 1970 K10 Join Date: Feb 2004 Location: Fort Collins, Colo 80524 Posts: 6,684	Re: Which motor mounts set the motor back the most? #2 and #3 are the most common plates. __________________ *Bob* 1970 Chevy K10 LWB "Goldie" 350/TH350 *next project!!* 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE

08-13-2010, 12:26 AM	#6
chevydog66 GM ONLY BABY!!! Join Date: Oct 2003 Location: Fort Wayne, IN. Posts: 1,998	Re: Which motor mounts set the motor back the most? Ok, ya so now I'm mad. I had the ECE mounts but sold them because the mounts were about 1" too far forward, now I have the Car Shop CSP 2349 mounts and its even worse. I want a LS motor mount that I will be able to use the LS clutch fan and the original 72 fan shroud, and the bellhousing flange meet up the trans. that is in the truck. Any suggestions? Thanks for the diagram Glock, I can visually see what I need now, who makes or sells the # 1's? I think that is what I need. Thinking about returning my 2349 for the 2370. __________________ 2 wrongs don't make a right, but 3 lefts do. 66 Chevelle Malibu 406ci, 573hp, 10.99@121mph 96 Chevy Silverado Z71 72 GMC 1500 Super Custom LS 6.0/4L65 on airride http://www.cardomain.com/ride/707879...mc-c-k-pick-up

08-14-2010, 12:12 PM	#7
glock35ipsc Next project: 1970 K10 Join Date: Feb 2004 Location: Fort Collins, Colo 80524 Posts: 6,684	Re: Which motor mounts set the motor back the most? No one makes #1 commercially that I am aware of. Someone might, but I just haven't seen them. I just included it in my diagram for the engine mount sticky. If those are the ones you need, they are super simple to make. These would be the closest: http://tpiparts.net/inc/sdetail/16936 __________________ *Bob* 1970 Chevy K10 LWB "Goldie" 350/TH350 *next project!!* 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE Last edited by glock35ipsc; 08-14-2010 at 12:17 PM.

08-15-2010, 01:48 PM	#8
chevydog66 GM ONLY BABY!!! Join Date: Oct 2003 Location: Fort Wayne, IN. Posts: 1,998	Re: Which motor mounts set the motor back the most? Thanks again Glock, you da man, I looked at those and considered them at first. __________________ 2 wrongs don't make a right, but 3 lefts do. 66 Chevelle Malibu 406ci, 573hp, 10.99@121mph 96 Chevy Silverado Z71 72 GMC 1500 Super Custom LS 6.0/4L65 on airride http://www.cardomain.com/ride/707879...mc-c-k-pick-up

08-12-2010, 11:37 AM	#1
chevydog66 GM ONLY BABY!!! Join Date: Oct 2003 Location: Fort Wayne, IN. Posts: 1,998	Which motor mounts set the motor back the most? I had the ECE mounts, now I have the Car Shop mounts, havent installed motor yet with new mounts, but it looks like they might set the motor even more forward than the ECE mounts. So which mounts would set the motor back the most? __________________ 2 wrongs don't make a right, but 3 lefts do. 66 Chevelle Malibu 406ci, 573hp, 10.99@121mph 96 Chevy Silverado Z71 72 GMC 1500 Super Custom LS 6.0/4L65 on airride http://www.cardomain.com/ride/707879...mc-c-k-pick-up

08-12-2010, 11:42 AM	#2
team39763 Registered User Join Date: Feb 2007 Location: Texas Posts: 469	Re: Which motor mounts set the motor back the most? Have you tried the 1" setback mounts that carshopinc makes? I had their regular mounts, but switched to another brand's 1" setback since carshopinc didn't make them at the time. It set my motor exactly where the old sbc used to be and my trans bolted right up. __________________ 1982 Silverado - SBE, cleaned up GM heads, small cam, TH350, 850 Demon, 4.56 gears, and caltracs. Best time so far 11.8@XXXMPH

08-16-2010, 11:26 AM	#9
Clyde65 1965 Chevy C10, 2005 4.8L/4l60 Join Date: Aug 2004 Location: DFW Texas Posts: 8,546	Re: Which motor mounts set the motor back the most? I used the POL stands, on the rear mounting holes and then used their mount plates too. I could use the shroud with a little trimmin. __________________ Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684 *support our troops!*

08-16-2010, 11:31 AM	#10
chevydog66 GM ONLY BABY!!! Join Date: Oct 2003 Location: Fort Wayne, IN. Posts: 1,998	Re: Which motor mounts set the motor back the most? I just ordered the tpiparts plates, shipped express, and will be returning my Car shop mounts. Hopefully I will be putting it in for the last time tomorrow. __________________ 2 wrongs don't make a right, but 3 lefts do. 66 Chevelle Malibu 406ci, 573hp, 10.99@121mph 96 Chevy Silverado Z71 72 GMC 1500 Super Custom LS 6.0/4L65 on airride http://www.cardomain.com/ride/707879...mc-c-k-pick-up

08-16-2010, 12:32 PM	#11
c10seconds Registered User Join Date: Oct 2009 Location: gilbert,AZ Posts: 947	Re: Which motor mounts set the motor back the most? Let us know how it sits. I may have to order some of those as well

08-20-2010, 11:23 AM	#12
team39763 Registered User Join Date: Feb 2007 Location: Texas Posts: 469	Re: Which motor mounts set the motor back the most? Mine sorta look like the ones in #1. I couldn't get a real good look at them since my hood is stuck. I believe mine are the S&P 1" setback mounts. Shortly after I bought mine to replace my standard carshopinc mounts, carshopinc started making 1" setback mounts. __________________ 1982 Silverado - SBE, cleaned up GM heads, small cam, TH350, 850 Demon, 4.56 gears, and caltracs. Best time so far 11.8@XXXMPH

08-23-2010, 12:15 AM	#14
eagleuh1 Registered User Join Date: Jul 2009 Location: Russellville, Arkansas Posts: 1,699	Re: Which motor mounts set the motor back the most? Have you tried using 6 cyl stands in rear position with the # 2 plates. This is what I used. Engine sits back pretty good.

08-28-2010, 10:19 PM	#16
joejbal Registered User Join Date: Oct 2009 Location: Wall, NJ Posts: 64	Re: Which motor mounts set the motor back the most? I agree, I used the 6 cyl stands with plates like number two, and a urethan version of the stock type mount. the engine sits very close to the firewall, like it was meant to go there. __________________ Joe

09-10-2010, 08:57 PM	#18
chevydog66 GM ONLY BABY!!! Join Date: Oct 2003 Location: Fort Wayne, IN. Posts: 1,998	Re: Which motor mounts set the motor back the most? Mine doesn't. I think I will have to go with the high mount bracket. __________________ 2 wrongs don't make a right, but 3 lefts do. 66 Chevelle Malibu 406ci, 573hp, 10.99@121mph 96 Chevy Silverado Z71 72 GMC 1500 Super Custom LS 6.0/4L65 on airride http://www.cardomain.com/ride/707879...mc-c-k-pick-up

09-11-2010, 07:28 AM	#19
eagleuh1 Registered User Join Date: Jul 2009 Location: Russellville, Arkansas Posts: 1,699	Re: Which motor mounts set the motor back the most? Mine does but I made my own compressor mount to move the AC in closer to the engine. No good pics available. Wish had taken some before engine install. I got some compressor blocks from Docs Blocks.com. Have put on yet.



Register or Log In To remove these advertisements.

09-20-2010, 07:44 PM	#20
68GMCCustom Truck and auto performance nut Join Date: Feb 2007 Location: McKinney,Texas Posts: 3,848	Re: Which motor mounts set the motor back the most? I'm hoping someone here can help. I too had the ECE mounts and found them to mount the motor too far forward and am now using some Transdapt mounts that are similar to #1. My question is.....now that I have the motor so much further back...will I still be able to get the cab on? __________________ Kurt - '68 GMC short step - NIB '09 LY6 6.0L crate motor w/mods, NIB '12 crate 4L85e w/billet 3k stall Circle D, 3.73 posi 12 bolt, DynaTech f-swap headers, 3/4 drop, handling mods, etc. - my toy '72 Chevy LWB C-10 Highlander - 350/350 ps/pb/tilt/ac - not original but close '06 Chevy TrailBlazerSS - LS2/4L70e - little black hot rod SUV - my DD '18 Kia Sorento - wife's econo-driver '95 Chevy S10 - reg cab shortbed, LS, 4.3, auto... my '68's powertrain and chassis build -links broken A surprise phase - carb to efi -links broken

09-20-2010, 07:51 PM	#21
68GMCCustom Truck and auto performance nut Join Date: Feb 2007 Location: McKinney,Texas Posts: 3,848	Re: Which motor mounts set the motor back the most? Mine is using 6cyl mounts and the rear holes...plus the mounts look like the set back further....too far back? __________________ Kurt - '68 GMC short step - NIB '09 LY6 6.0L crate motor w/mods, NIB '12 crate 4L85e w/billet 3k stall Circle D, 3.73 posi 12 bolt, DynaTech f-swap headers, 3/4 drop, handling mods, etc. - my toy '72 Chevy LWB C-10 Highlander - 350/350 ps/pb/tilt/ac - not original but close '06 Chevy TrailBlazerSS - LS2/4L70e - little black hot rod SUV - my DD '18 Kia Sorento - wife's econo-driver '95 Chevy S10 - reg cab shortbed, LS, 4.3, auto... my '68's powertrain and chassis build -links broken A surprise phase - carb to efi -links broken Last edited by 68GMCCustom; 09-20-2010 at 07:52 PM.

09-21-2010, 10:46 AM	#23
68GMCCustom Truck and auto performance nut Join Date: Feb 2007 Location: McKinney,Texas Posts: 3,848	Re: Which motor mounts set the motor back the most? well duh. I was using your pic for comparison.... because I didn't have any of mine...now I do...here's mine: __________________ Kurt - '68 GMC short step - NIB '09 LY6 6.0L crate motor w/mods, NIB '12 crate 4L85e w/billet 3k stall Circle D, 3.73 posi 12 bolt, DynaTech f-swap headers, 3/4 drop, handling mods, etc. - my toy '72 Chevy LWB C-10 Highlander - 350/350 ps/pb/tilt/ac - not original but close '06 Chevy TrailBlazerSS - LS2/4L70e - little black hot rod SUV - my DD '18 Kia Sorento - wife's econo-driver '95 Chevy S10 - reg cab shortbed, LS, 4.3, auto... my '68's powertrain and chassis build -links broken A surprise phase - carb to efi -links broken Last edited by 68GMCCustom; 09-21-2010 at 10:46 AM.

09-21-2010, 09:54 PM	#24
68GMCCustom Truck and auto performance nut Join Date: Feb 2007 Location: McKinney,Texas Posts: 3,848	Re: Which motor mounts set the motor back the most? I guess the more I look....the motor mount looks to be in the same location on the motor plate as yours chevydog? __________________ Kurt - '68 GMC short step - NIB '09 LY6 6.0L crate motor w/mods, NIB '12 crate 4L85e w/billet 3k stall Circle D, 3.73 posi 12 bolt, DynaTech f-swap headers, 3/4 drop, handling mods, etc. - my toy '72 Chevy LWB C-10 Highlander - 350/350 ps/pb/tilt/ac - not original but close '06 Chevy TrailBlazerSS - LS2/4L70e - little black hot rod SUV - my DD '18 Kia Sorento - wife's econo-driver '95 Chevy S10 - reg cab shortbed, LS, 4.3, auto... my '68's powertrain and chassis build -links broken A surprise phase - carb to efi -links broken

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.