Fender emblem mounting - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Tx Firefighter · 01-07-2011, 10:10 PM

I'm fixing up some extra fenders for my 78 truck. My question is about the hole pattern for the fender emblems. Are they all the same for the various emblems ? I know this seems a foolish question, but I figure to turn up a pair of Silverado 30 emblems at the swap meets next summer and wonder if they will drop right in to the existing holes. Knowing this would allow me to go ahead and paint all the body panels knowing the holes were proper for any emblem.

f.monroe · 01-07-2011, 11:10 PM

I am pretty sure there is only one bolt pattern. GM actually sold the new fenders with the holes already punched for the emblems.
Frank

Keith Seymore · 01-08-2011, 04:32 PM

The holes were all the same. Otherwise we would have had to proliferate fenders just to use the different emblems.

K

Jonboy · 01-09-2011, 09:50 AM

If you are going to install them before the emblems, try to find some barrel clips to hold the emblems in place. It's are dang near impossible to get to the back of the emblem with the fender on the truck.

Tx Firefighter · 01-09-2011, 12:34 PM

I appreciate the answers everyone.

What I'm doing is prepping and painting extra body panels for an old truck I'm restoring. I'm going to get the door, fenders and hood all painted up then install it onto the truck at one time.

01-07-2011, 10:10 PM	#1
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Fender emblem mounting I'm fixing up some extra fenders for my 78 truck. My question is about the hole pattern for the fender emblems. Are they all the same for the various emblems ? I know this seems a foolish question, but I figure to turn up a pair of Silverado 30 emblems at the swap meets next summer and wonder if they will drop right in to the existing holes. Knowing this would allow me to go ahead and paint all the body panels knowing the holes were proper for any emblem. __________________ I'm on the Instagram- @Gearhead_Kevin

01-07-2011, 11:10 PM	#2
f.monroe Senior Member Join Date: May 2004 Location: Caldwell,Tx. Posts: 3,648	Re: Fender emblem mounting I am pretty sure there is only one bolt pattern. GM actually sold the new fenders with the holes already punched for the emblems. Frank __________________ Born and proudly residing in a Red State !

01-08-2011, 04:32 PM	#3
Keith Seymore Registered User Join Date: May 2009 Location: Motor City Posts: 9,226	Re: Fender emblem mounting The holes were all the same. Otherwise we would have had to proliferate fenders just to use the different emblems. K __________________ Chevrolet Flint Assembly 1979-1986 GM Full Size Truck Engineering 1986 - 2019 Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926 My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524 Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/

01-09-2011, 09:50 AM	#4
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	Re: Fender emblem mounting If you are going to install them before the emblems, try to find some barrel clips to hold the emblems in place. It's are dang near impossible to get to the back of the emblem with the fender on the truck. __________________ 1974 Jimmy- 5.3/4L80e/NP241

01-09-2011, 12:34 PM	#5
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: Fender emblem mounting I appreciate the answers everyone. What I'm doing is prepping and painting extra body panels for an old truck I'm restoring. I'm going to get the door, fenders and hood all painted up then install it onto the truck at one time. __________________ I'm on the Instagram- @Gearhead_Kevin

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.