|
05-25-2011, 10:41 PM
|
#1 |
|
Custom Builder
 
Join Date: Jun 2003
Location: Carlsbad, California
Posts: 908
|
17X9 Steel Wheels
These are the Steel Wheels I had made up in 17X9 with 5" of backspace. They have to clear a D60 and 14B FF with Disc Brake Conversion. They fit like a glove over the brakes and steering.
They are a little dusty from setting around in the garage.  
__________________
1932 Chevy Roadster Car and Pick-Up - http://67-72chevytrucks.com/vboard/s...d.php?t=465709 1966 K20 Factory 4X4 - http://67-72chevytrucks.com/vboard/s...d.php?t=455484 (Sold) 1972 K5 Blazer (Sold) - http://67-72chevytrucks.com/vboard/s...ad.php?t=87530 2007 TrailBlazer SS - http://67-72chevytrucks.com/vboard/s...34#post4706534 Last edited by LeftCoast32; 05-25-2011 at 10:45 PM. |
|
|
|
05-26-2011, 06:03 PM
|
#2 |
|
Custom Builder
Join Date: Jun 2003
Location: Carlsbad, California
Posts: 908
|
Re: 17X9 Steel Wheels
The plan is to run the real long chrome lugs front and rear.
I am going to run a set of real thin Stainless Steel Trim Rings. The Dana 60 Mile Marker Hubs are Polished Stainless Steel. The 14Bolt FF will have Polished Stainless Steel Axle Shaft Bolts. Should look pretty good when finished.
__________________
1932 Chevy Roadster Car and Pick-Up - http://67-72chevytrucks.com/vboard/s...d.php?t=465709 1966 K20 Factory 4X4 - http://67-72chevytrucks.com/vboard/s...d.php?t=455484 (Sold) 1972 K5 Blazer (Sold) - http://67-72chevytrucks.com/vboard/s...ad.php?t=87530 2007 TrailBlazer SS - http://67-72chevytrucks.com/vboard/s...34#post4706534 |
|
|
|
|
05-26-2011, 06:09 PM
|
#3 |
|
Registered User
Join Date: May 2005
Location: Beaverton, OR
Posts: 3,728
|
Re: 17X9 Steel Wheels
Nice, where did you have them made?
There used to be a shop around here that would make custom steel wheels, but they went under a while back.
__________________
New Project: 1966 LWB C20 Plans: 1/2 ton conversion Dropmember front Dropmember rear Corvette discs Restored raised bed http://67-72chevytrucks.com/vboard/s....php?p=4295210 |
|
|
|
|
05-26-2011, 06:46 PM
|
#4 |
|
Check The Champ, Demonstrator
Join Date: Jun 2009
Location: Montreal,Quebec
Posts: 6,627
|
Re: 17X9 Steel Wheels
Interesting, I made a set of 17" 6 bolt pattern, modified from the stock 17.5" that was available in our series. In your 8 bolt pattern you could get up to a 19.5" wheel optioned.
__________________
1963 Chevrolet Truck Literature LINK: https://picasaweb.google.com/113840717762774560215 YouTube Channel with 20+ Original Chevrolet Truck Salesmen, Mechanics & Service Department Training Slideshows. https://www.youtube.com/results?sear...otruk63&page=1 |
|
|
|
|
05-26-2011, 07:24 PM
|
#5 |
|
Custom Builder
Join Date: Jun 2003
Location: Carlsbad, California
Posts: 908
|
Re: 17X9 Steel Wheels
I had them made by a company that supplies all the outer hoops and inner wheel centers to all the companies that sell steel wheels. They dont deal direct with the public at all, sorry.
I went with the 17's because of all the tire choices. I will be running 37/12.50x17 BFG Mud Terrain KM2's.
__________________
1932 Chevy Roadster Car and Pick-Up - http://67-72chevytrucks.com/vboard/s...d.php?t=465709 1966 K20 Factory 4X4 - http://67-72chevytrucks.com/vboard/s...d.php?t=455484 (Sold) 1972 K5 Blazer (Sold) - http://67-72chevytrucks.com/vboard/s...ad.php?t=87530 2007 TrailBlazer SS - http://67-72chevytrucks.com/vboard/s...34#post4706534 Last edited by LeftCoast32; 05-26-2011 at 07:25 PM. |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
