NY 87 K20 Roller Parts or Whole - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Sarge261 · 06-19-2011, 06:55 PM

Hey folks,

I have a 87 K20 roller I am going to part/sell whole. I had a buyer and not sure what happend. This truck has no front clip, engine, trans, or wire harnesses. The cab needs floors, rockers and cab corners, the fire wall seem is perfect. It has some a/m doors on it in good shape.

The box is nice, no rust on the cross supports, wheel wells, floor, etc. It has a hole in the bed where an air line was run up to it. This truck was a Peterbuilt service truck from South Carolina. I dont have the tail gate to the truck but have a nice GMC gate to go with it if you would like.

The frame is in great shape with no rust at all, its a bare frame with just brake lines. It has no fuel tanks, or fuel lines. It has a 14 bolt rear and 10 bolt front.

I would like 750.00 obo for the box
I would like 200.00 obo for the cab
I would like 500.00 obo for the chassis

1250.00 obo takes it all

I will post pictures tomarrow when I go back to the shop.

I need this thing gone, the city has begun citing me because the other buyer was supposed to take it away in May.

Any questions or specific parts you need from it let me know.

I can help with delivery if its resonably close, within a few hundred miles.

Sarge

**thinair** · 06-20-2011, 02:20 AM

Is the tcase there? NP208? 4.10 gears? Looking for a speedo gear.
Posted via Mobile Device

Sarge261 · 06-20-2011, 08:20 AM

It has 3.73, the T-case I am using in my project.

Sarge

Sarge261 · 06-24-2011, 08:23 AM

TTT,

I will have pictures up later today. I am sorry for the delay.

Any reasonable offers will be accepted.

Sarge

Sarge261 · 06-26-2011, 11:19 AM

Pics. Sorry it took so long:

Sarge261 · 06-26-2011, 11:21 AM

More Pics:

Sarge261 · 06-26-2011, 11:23 AM

More:

Sarge261 · 06-29-2011, 12:17 PM

TTT,

No one in the North East needs a Rust free bed, and chassis?

scubasteve16 · 06-29-2011, 08:15 PM

I would love to have the bed but the distance would kill it for me...

**old Rusty C10** · 06-29-2011, 10:11 PM

are those gm factory cab lights on it?

Sarge261 · 06-30-2011, 08:13 AM

Yes they are factory cab lights on the truck.

I would love to make the bed work for you buy yes the distance would be a deal breaker. Its too bad I dont want to send this thing to the crusher and the city is up my behind to get rid of it.

Sarge

**old Rusty C10** · 06-30-2011, 08:44 AM

how much for the cab lights , the tioops and bottoms and a good length of wire with each? that would be shipped to 08859 in NJ unless youre near binghamton or deposit and i could pick up from you on next trip..

Sarge261 · 06-30-2011, 03:34 PM

Bob,

Hows 85.00 shipped for everything. Im not sure how much they are worth so if thats too high make me an offer.

Sarge

**old Rusty C10** · 07-04-2011, 09:53 AM

I dont want to be insulting to you but this was a recent sale of same i was thinking more along these lines:
http://67-72chevytrucks.com/vboard/s...d.php?t=464467

Sarge261 · 07-04-2011, 06:47 PM

No insults at all.

I cant keep track what things are worth on these old squares, Ive been out of the game on these things for so long. I can do 30.00 let me just check on the shipping, not sure what the next up flate rate box is from the 5.00 one.

Im in Albany NY but I am heading to PA in August and go right through Binghampton I usually go 88 then to 81 south. Not sure where you are from there but Like I said I'll be through there mid August otherwise I'll ship.

Sarge

Sarge261 · 07-04-2011, 06:55 PM

SEAT BELT PICS FOR WhiskeyDented:

**old Rusty C10** · 07-05-2011, 09:22 AM

Sarge im actually in NJ . My home in Deposit ( near binghamton) is a vacation home. I think we are going to have to ship them.. let me know how you want payment and ill send it out to you

Sarge261 · 07-05-2011, 11:45 AM

You will have to give me some time to get them out, I hurt my back so I am taking it easy for a little bit here.

Sarge

Sarge261 · 07-08-2011, 08:23 PM

Anyone ned the box cab and frame....anyone offers accepted

jasonroman · 07-11-2011, 08:34 AM

price on the bed ??

Sarge261 · 07-11-2011, 08:43 AM

750.00 or best offer. I need this thing gone the fines are piling up.

Sarge

06-19-2011, 06:55 PM	#1
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	87 K20 Roller Parts or Whole Hey folks, I have a 87 K20 roller I am going to part/sell whole. I had a buyer and not sure what happend. This truck has no front clip, engine, trans, or wire harnesses. The cab needs floors, rockers and cab corners, the fire wall seem is perfect. It has some a/m doors on it in good shape. The box is nice, no rust on the cross supports, wheel wells, floor, etc. It has a hole in the bed where an air line was run up to it. This truck was a Peterbuilt service truck from South Carolina. I dont have the tail gate to the truck but have a nice GMC gate to go with it if you would like. The frame is in great shape with no rust at all, its a bare frame with just brake lines. It has no fuel tanks, or fuel lines. It has a 14 bolt rear and 10 bolt front. I would like 750.00 obo for the box I would like 200.00 obo for the cab I would like 500.00 obo for the chassis 1250.00 obo takes it all I will post pictures tomarrow when I go back to the shop. I need this thing gone, the city has begun citing me because the other buyer was supposed to take it away in May. Any questions or specific parts you need from it let me know. I can help with delivery if its resonably close, within a few hundred miles. Sarge __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

06-20-2011, 02:20 AM	#2
thinair thinair Join Date: Jun 2004 Location: omaha,ne Posts: 1,010	Re: 87 K20 Roller Parts or Whole Is the tcase there? NP208? 4.10 gears? Looking for a speedo gear. Posted via Mobile Device

06-20-2011, 08:20 AM	#3
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole It has 3.73, the T-case I am using in my project. Sarge __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

06-24-2011, 08:23 AM	#4
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole TTT, I will have pictures up later today. I am sorry for the delay. Any reasonable offers will be accepted. Sarge __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

06-26-2011, 11:19 AM	#5
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole Pics. Sorry it took so long: Attached Images __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

06-26-2011, 11:21 AM	#6
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole More Pics: Attached Images __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

06-26-2011, 11:23 AM	#7
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole More: Attached Images __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

06-29-2011, 12:17 PM	#8
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole TTT, No one in the North East needs a Rust free bed, and chassis? __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

06-29-2011, 08:15 PM	#9
scubasteve16 Registered User Join Date: Sep 2010 Location: Abilene Kansas Posts: 78	Re: 87 K20 Roller Parts or Whole I would love to have the bed but the distance would kill it for me... __________________ "If it throws you back in the seat when it shifts, it was slowing down before it shifted" Disturbed Customs 1992 Chevy 1/2 ton 4x4 wore out 350 1975 Chevy 3/4 ton 4x4/ 8" suspension lift/ 468 Big Block/ 4 speed/ 4.56 gears/ 17' American Racing simulated beadlocks with Pro Comp 37x12.50 tires 1950 Pontiac Chieftain Straight 8/Hydromatic tranny

06-29-2011, 10:11 PM	#10
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,316	Re: 87 K20 Roller Parts or Whole are those gm factory cab lights on it? __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

06-30-2011, 08:13 AM	#11
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole Yes they are factory cab lights on the truck. I would love to make the bed work for you buy yes the distance would be a deal breaker. Its too bad I dont want to send this thing to the crusher and the city is up my behind to get rid of it. Sarge __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

06-30-2011, 08:44 AM	#12
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,316	Re: 87 K20 Roller Parts or Whole how much for the cab lights , the tioops and bottoms and a good length of wire with each? that would be shipped to 08859 in NJ unless youre near binghamton or deposit and i could pick up from you on next trip.. __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

06-30-2011, 03:34 PM	#13
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole Bob, Hows 85.00 shipped for everything. Im not sure how much they are worth so if thats too high make me an offer. Sarge __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

07-04-2011, 09:53 AM	#14
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,316	Re: 87 K20 Roller Parts or Whole I dont want to be insulting to you but this was a recent sale of same i was thinking more along these lines: http://67-72chevytrucks.com/vboard/s...d.php?t=464467 __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

07-04-2011, 06:47 PM	#15
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole No insults at all. I cant keep track what things are worth on these old squares, Ive been out of the game on these things for so long. I can do 30.00 let me just check on the shipping, not sure what the next up flate rate box is from the 5.00 one. Im in Albany NY but I am heading to PA in August and go right through Binghampton I usually go 88 then to 81 south. Not sure where you are from there but Like I said I'll be through there mid August otherwise I'll ship. Sarge __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR



Register or Log In To remove these advertisements.

07-04-2011, 06:55 PM	#16
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole SEAT BELT PICS FOR WhiskeyDented: Attached Images __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

07-05-2011, 09:22 AM	#17
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,316	Re: 87 K20 Roller Parts or Whole Sarge im actually in NJ . My home in Deposit ( near binghamton) is a vacation home. I think we are going to have to ship them.. let me know how you want payment and ill send it out to you __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

07-05-2011, 11:45 AM	#18
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole You will have to give me some time to get them out, I hurt my back so I am taking it easy for a little bit here. Sarge __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

07-08-2011, 08:23 PM	#19
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole Anyone ned the box cab and frame....anyone offers accepted __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

07-11-2011, 08:34 AM	#20
jasonroman Registered User Join Date: Jul 2008 Location: sayreville nj Posts: 1,072	Re: 87 K20 Roller Parts or Whole price on the bed ??

07-11-2011, 08:43 AM	#21
Sarge261 Registered User Join Date: Sep 2009 Location: Upstate NY Posts: 395	Re: 87 K20 Roller Parts or Whole 750.00 or best offer. I need this thing gone the fines are piling up. Sarge __________________ 1997 GMC Yukon Western Mid Weight Plow Project THOR

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.