TX hedman hedders for 67-87 C10 sbc - The 1947 - Present Chevrolet & GMC Truck Message Board Network

67 c10 guy · 08-15-2011, 01:53 AM

Im selling a set of hedman longtube hedders w/3" collector.
They fit 67-87 C10 sbc. They do have surface rust
but should clean up fine, still very solid/no rust through

http://www.summitracing.com/parts/HED-69090/

hedman longtube hedders - $75 plus shipping
however shipping may kill the deal since the box would need to be
40x20x12 and total weight is about 25 Lbs

MYKG C10 · 09-15-2011, 10:04 PM

Hey Bro do you still have em i need for my 69

67 c10 guy · 09-16-2011, 03:43 AM

yes, i still have them.

**special-K** · 09-16-2011, 08:18 AM

What happened to the collector flanges? Were these used on a drag truck? Is there a way I could run an exhaust off of these?

67 c10 guy · 09-16-2011, 11:53 AM

I guess the po just had pipe welded to the collector.
There never was a flange since I have owned it.
But they are the exact headers listed in the summit site link
Minus the flange that po cut off and welded to
Posted via Mobile Device

08-15-2011, 01:53 AM	#1
67 c10 guy Registered User Join Date: Jan 2009 Location: 77042, Texas Posts: 102	hedman hedders for 67-87 C10 sbc Im selling a set of hedman longtube hedders w/3" collector. They fit 67-87 C10 sbc. They do have surface rust but should clean up fine, still very solid/no rust through http://www.summitracing.com/parts/HED-69090/ hedman longtube hedders - $75 plus shipping however shipping may kill the deal since the box would need to be 40x20x12 and total weight is about 25 Lbs __________________ 67 C10 longbed 350/th350 13 Ford Fusion 2.0T daily 67 lwb build sold Last edited by 67 c10 guy; 09-16-2011 at 03:43 AM.

09-15-2011, 10:04 PM	#2
MYKG C10 Registered User Join Date: Apr 2008 Location: houston Posts: 17	Re: hedman hedders for 67-87 C10 sbc Hey Bro do you still have em i need for my 69

09-16-2011, 03:43 AM	#3
67 c10 guy Registered User Join Date: Jan 2009 Location: 77042, Texas Posts: 102	Re: hedman hedders for 67-87 C10 sbc yes, i still have them. __________________ 67 C10 longbed 350/th350 13 Ford Fusion 2.0T daily 67 lwb build sold

09-16-2011, 08:18 AM	#4
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: hedman hedders for 67-87 C10 sbc What happened to the collector flanges? Were these used on a drag truck? Is there a way I could run an exhaust off of these? __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

09-16-2011, 11:53 AM	#5
67 c10 guy Registered User Join Date: Jan 2009 Location: 77042, Texas Posts: 102	Re: hedman hedders for 67-87 C10 sbc I guess the po just had pipe welded to the collector. There never was a flange since I have owned it. But they are the exact headers listed in the summit site link Minus the flange that po cut off and welded to Posted via Mobile Device __________________ 67 C10 longbed 350/th350 13 Ford Fusion 2.0T daily 67 lwb build sold

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.