passanger side sunvisor 65 stepside - The 1947 - Present Chevrolet & GMC Truck Message Board Network

niterider65 · 10-30-2011, 08:13 PM

Hey dose any one have or done a passanger side visor install i have bought the the left and right side visors .i need the specs on tthe center hole or a
templet so i don't butcher it up..

i can see the marks of the 2 lower holes. and theres a demple in the middle .. ..

66farmer · 10-30-2011, 08:51 PM

I had the same question. After looking at it and doing some measurements I drilled the dimple I hope it's right didn't have a viser to check it and the cab had to go to paint.

markeb01 · 10-30-2011, 10:59 PM

The following instructions are from the 1960 Accessories Installation Manual. I know the windshield pillar is different from a 65, but I think the roof panel is the same from 60-66. Unfortunately the factory never did provide dimensions, just a template. Perhaps the illustration will at least help with orientation of the screws.

niterider65 · 10-30-2011, 11:22 PM

Thanks mark that will give me an idea of tracing my driver side and slipping it over
the old saying is measure twice and cut ones ..

ol Curt · 10-31-2011, 08:38 PM

Mine had three dimples in the exact mirrored spots of the drivers side

10-30-2011, 08:13 PM	#1
niterider65 Registered User Join Date: Jun 2011 Location: colleyville tx Posts: 624	passanger side sunvisor 65 stepside Hey dose any one have or done a passanger side visor install i have bought the the left and right side visors .i need the specs on tthe center hole or a templet so i don't butcher it up.. i can see the marks of the 2 lower holes. and theres a demple in the middle .. .. Attached Images

10-30-2011, 08:51 PM	#2
66farmer Registered User Join Date: Jun 2007 Location: North Plains Oregon Posts: 684	Re: passanger side sunvisor 65 stepside I had the same question. After looking at it and doing some measurements I drilled the dimple I hope it's right didn't have a viser to check it and the cab had to go to paint.

10-30-2011, 10:59 PM	#3
markeb01 Senior Enthusiast Join Date: Feb 2007 Location: Spokane Valley, WA Posts: 8,356	Re: passanger side sunvisor 65 stepside The following instructions are from the 1960 Accessories Installation Manual. I know the windshield pillar is different from a 65, but I think the roof panel is the same from 60-66. Unfortunately the factory never did provide dimensions, just a template. Perhaps the illustration will at least help with orientation of the screws.

10-30-2011, 11:22 PM	#4
niterider65 Registered User Join Date: Jun 2011 Location: colleyville tx Posts: 624	Re: passanger side sunvisor 65 stepside Thanks mark that will give me an idea of tracing my driver side and slipping it over the old saying is measure twice and cut ones ..

10-31-2011, 08:38 PM	#5
ol Curt Junior Member Join Date: Dec 2006 Location: Newburgh, IN Posts: 1,247	Re: passanger side sunvisor 65 stepside Mine had three dimples in the exact mirrored spots of the drivers side __________________ 1966 Chevy C10 Longbed I'm Bob....ol Curt was my Grandpa The truck was his and he sure as heck wouldn't understand why I took a perfectly good truck and tore it down!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.