|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-29-2012, 09:49 PM
|
#1 |
|
Registered User
Join Date: Jul 2011
Location: Vernon BC Canada
Posts: 287
|
what can i do about this exhaust?
ok so i just put the rear air bags in and im just waiting for my drop spindles and 5 bolt swap to do the front bags...now my problem is the 250 inline 6 exhaust hang down so low its crazy...i want this truck low and i need to get this thing out of my way should i take it back to stock? right now it has a header that turns it into 2 pipes very cool but soooooo low ..any ideas?i want to lay frame at the end of my build so keep that in mind
|
|
|
|
03-29-2012, 11:17 PM
|
#2 |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
|
Re: what can i do about this exhaust?
Stock exhaust manifold or custom built header.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
03-29-2012, 11:20 PM
|
#3 | |
|
Registered User
Join Date: Aug 2010
Location: AZ
Posts: 3,069
|
Re: what can i do about this exhaust?
Quote:
|
|
|
|
|
|
03-30-2012, 01:22 AM
|
#4 |
|
Registered User
Join Date: Jan 2009
Location: Louisville,Ky
Posts: 5,811
|
Re: what can i do about this exhaust?
Look on speedway motors see if they sell a shorty header for it would be your best bet.
|
|
|
|
|
03-30-2012, 09:46 AM
|
#5 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: what can i do about this exhaust?
cut and weld what you got to make them betterer
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
|
03-30-2012, 09:56 AM
|
#6 | |
|
Registered User
Join Date: Aug 2009
Location: New Prague, MN
Posts: 103
|
Re: what can i do about this exhaust?
Quote:
__________________
Live life one weld at a time. '04.5 Chev Duramax CCLB- Winter DD '03 Grand Prix GT- Summer DD '67 C10-307/T5(For Now)-R.I.P-Burned Up! '68 C10-5.3/4L80E www.one-guys-garage.com |
|
|
|
|
|
03-30-2012, 10:36 AM
|
#7 |
|
Happy to be here
 
Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,021
|
Re: what can i do about this exhaust?
Your going to have to change it. Either replace those headers or cut till they are even with the frame. You mentioned you can weld, so lets see what you got.
__________________
Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" |
|
|
|
|
03-30-2012, 11:53 AM
|
#8 |
|
Registered User
Join Date: Jul 2011
Location: Vernon BC Canada
Posts: 287
|
Re: what can i do about this exhaust?
ya it not the welding im worried about its the where do i run 2 pipes down one side i want it up in the frame....i would just swap out the motor and be done with it but its great on gas..
|
|
|
|
|
03-30-2012, 01:07 PM
|
#9 |
|
Registered User
 
Join Date: May 2011
Location: Missoula, MT
Posts: 934
|
Re: what can i do about this exhaust?
Why don’t you shorten the headers to pick them up in the frame rails then y them into a single 2 ¾” or 3” pipe and rout it like a v8. The volume you will be pushing with that engine will be well with in the 2 ¾” pipes cfm rate and it will be easy to rout.
|
|
|
|
|
03-30-2012, 03:56 PM
|
#10 |
|
Registered User
Join Date: Jul 2011
Location: Vernon BC Canada
Posts: 287
|
Re: what can i do about this exhaust?
sounds good to me thanx
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
