|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
06-21-2012, 10:59 AM
|
#1 |
|
Knuckle head
Join Date: Mar 2008
Location: NC
Posts: 283
|
A 9" rearend question for the "Mad Scientists"
I ordered the Currie 9+ Centurion Ford 9" reared end housing, 3" DOM tubes, late model big Ford billet housing ends to go in my '71.
My question is; should I center the housing or center the pinion? I have heard that Ford centered the housing in order to have constant pinion angle laterally or side-2-side as well as the vertical pinion angle. I would rather have equal length axles and the housing centered but am willing to center the pinion if needed. All advice is greatly appreciated. Respectfully, Adam
__________________
Adam '71 SWB/Step  http://67-72chevytrucks.com/vboard/s...d.php?t=2917502017 Crew Cab Silverado LTZ with 6.2l, 8 Speed tuned by RPM in Garner, NC '00 Chevy 1500 6.0l Silverado Reg. Cab Short Bed '09 Chevy 1500 5.3l Silverado Crew Cab Short Bed (SOLD) 1971 LWB on 2014 1 ton chassis, L96 6.0LS / 6L90E http://67-72chevytrucks.com/vboard/s...d.php?t=796785 1969 LWB C10- Future project, possible AWD C10 on a 2002 Escalade Chassis. 
|
|
|
|
06-21-2012, 11:27 AM
|
#2 |
|
Happy to be here
 
Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,021
|
Re: A 9" rearend question for the "Mad Scientists"
If it were me, I would ask the tech at Curries. No one knows 9" Fords better than them.
__________________
Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" |
|
|
|
|
06-21-2012, 11:39 AM
|
#3 |
|
Senior Member
 
Join Date: Jul 2010
Location: Dandridge, Tn. USA
Posts: 2,226
|
Re: A 9" rearend question for the "Mad Scientists"
I always (shouldn't sat that) use a pinion centered housing, as it keeps the driveshaft straight back. - For cars/trucks built for show, I would use a housing centered for looks.
__________________
GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion Proud to put our products up against all others! |
|
|
|
|
06-21-2012, 01:16 PM
|
#4 | |
|
Registered User
Join Date: Dec 2004
Location: Aztec, NM
Posts: 388
|
Re: A 9" rearend question for the "Mad Scientists"
Quote:
__________________
Super Blue - 1968 C-10 Short Stepside
Fastburn 385, 4-Speed Sag. on the Column, Coleman 9" Floater w/Detroit TrueTrac |
|
|
|
|
|
06-21-2012, 11:59 PM
|
#5 |
|
Registered User
Join Date: Jan 2006
Location: Cherry Valley,Ca
Posts: 468
|
Re: A 9" rearend question for the "Mad Scientists"
Id center the housing so that you are guaranteed to have bearing movement in the u-joints even if the the drive shaft, trans and pinion are perferfectly parallel to the ground but truthfully it probably doesnt matter too much.
|
|
|
|
|
06-22-2012, 10:32 AM
|
#6 |
|
At the body shop.
Join Date: Aug 2009
Location: Land of fruits and nuts.
Posts: 5,257
|
Re: A 9" rearend question for the "Mad Scientists"
Centered pinion makes more room for mufflers.
Posted via Mobile Device
__________________
" That didnt make it any newer " " Dont antique the equipment " |
|
|
|
|
06-22-2012, 10:48 AM
|
#7 |
|
Knuckle head
Join Date: Mar 2008
Location: NC
Posts: 283
|
Re: A 9" rearend question for the "Mad Scientists"
Ok, this is great. Are there anymore pro's and con's I can get on either set-up?
Also, I am pretty sure I posted this in the wrong section, my apologies. Respectfully, Adam
__________________
Adam '71 SWB/Step http://67-72chevytrucks.com/vboard/s...d.php?t=2917502017 Crew Cab Silverado LTZ with 6.2l, 8 Speed tuned by RPM in Garner, NC '00 Chevy 1500 6.0l Silverado Reg. Cab Short Bed '09 Chevy 1500 5.3l Silverado Crew Cab Short Bed (SOLD) 1971 LWB on 2014 1 ton chassis, L96 6.0LS / 6L90E http://67-72chevytrucks.com/vboard/s...d.php?t=796785 1969 LWB C10- Future project, possible AWD C10 on a 2002 Escalade Chassis.
|
|
|
|
|
06-22-2012, 10:59 AM
|
#8 |
|
Registered User
Join Date: Oct 2008
Location: oxnard ca
Posts: 2,201
|
Re: A 9" rearend question for the "Mad Scientists"
Center your pinion in your frame to keep your driveshaft straight.'
Justin |
|
|
|
|
06-22-2012, 11:09 AM
|
#9 | |
|
Knuckle head
Join Date: Mar 2008
Location: NC
Posts: 283
|
Re: A 9" rearend question for the "Mad Scientists"
Quote:
When I get home I will need to send back the rear Wilwood kit for one with the late model big ford bracket. I made a last minute decision to get rid of the 12 bolt. I will call you when I get home and we can discuss this more. Thanks for your help last week. Respecfully, Adam
__________________
Adam '71 SWB/Step http://67-72chevytrucks.com/vboard/s...d.php?t=2917502017 Crew Cab Silverado LTZ with 6.2l, 8 Speed tuned by RPM in Garner, NC '00 Chevy 1500 6.0l Silverado Reg. Cab Short Bed '09 Chevy 1500 5.3l Silverado Crew Cab Short Bed (SOLD) 1971 LWB on 2014 1 ton chassis, L96 6.0LS / 6L90E http://67-72chevytrucks.com/vboard/s...d.php?t=796785 1969 LWB C10- Future project, possible AWD C10 on a 2002 Escalade Chassis.
|
|
|
|
|
|
06-22-2012, 11:23 AM
|
#10 |
|
Registered User
Join Date: Oct 2008
Location: oxnard ca
Posts: 2,201
|
Re: A 9" rearend question for the "Mad Scientists"
No problem call us up and we will help you out and take care of you
Justin |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
