|
06-28-2013, 03:24 PM
|
#1 |
|
Registered User
 Join Date: May 2013
Location: Houston, tx
Posts: 97
|
Oil Pan
Am I going to need a different oil pan for my swap? I am putting a 5.3 V8 into my 85 pick up? My truck sits at stock height.
|
|
|
|
06-28-2013, 04:10 PM
|
#2 |
|
Senior Member
 
Join Date: Sep 2005
Location: Lewisville, Nc
Posts: 10,237
|
Re: Oil Pan
stock 5.3 p[an should clear
__________________
David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube |
|
|
|
|
06-28-2013, 04:56 PM
|
#3 |
|
meowMEOWmeowMEOW
Join Date: Sep 2009
Location: MKE WI
Posts: 7,128
|
Re: Oil Pan
It will fit but hang a bit below the cross member. At stock height this is not a problem to you, so mechanically the pan will work fine.
__________________
'66 Short Step / SD Tuned / Big Cam LQ4 / Backhalfed /Built 4l80e / #REBUILDEVERYTHING  |
|
|
|
|
06-28-2013, 07:00 PM
|
#4 |
|
1965 Chevy C10, 2005 4.8L/4l60
Join Date: Aug 2004
Location: DFW Texas
Posts: 8,546
|
Re: Oil Pan
while you have it out, throw a GMPP LSX pan on it. then if you or the next owner wants to lower, there wont be any issues.
__________________
Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684  support our troops! |
|
|
|
|
06-29-2013, 01:03 AM
|
#5 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
Re: Oil Pan
^....that is what I opted for. For a 150 bones, it was hard to pass on(complete with gasket, tray/hardware & dip stick/tube). You loose about 1 Q capacity vs the truck pan, but gain about 1 1/4" in clearance. Longhorn
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
07-06-2013, 03:59 PM
|
#6 | |
|
Registered User
Join Date: May 2013
Location: Houston, tx
Posts: 97
|
Re: Oil Pan
Quote:
|
|
|
|
|
|
07-06-2013, 08:16 PM
|
#7 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
Re: Oil Pan
GMPP Hotrod pan (basically a Hummer H-3 pan). It is complete with gasket & dip stick & pickup tube.Also windage tray . Give me a minute, Ill get the PN....Longhorn Jegs # 809-19212593....10 bones cheaper now, says ships Monday! For the Gm pn, drop the 809 off the front. My truck is lowered, but not "slammed"....if you are on bags, & on the ground, your f body pan may be the ticket , or the Holley pan....best of fun
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... Last edited by crazy longhorn; 07-06-2013 at 08:27 PM. Reason: More info |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
\\ MY YOUTUBE CHANNEL
Linear Mode
