Haven't seen this lately. What did you do this weekend? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

KQQL IT · 07-28-2013, 09:26 PM

Polished the wheels.
Posted via Mobile Device

mongoose · 07-28-2013, 09:28 PM

360 nationals took up most of it.... might get out and pull the carpet today.

foamypirate · 07-28-2013, 09:53 PM

Dropped the 700R4 and installed a fresh TH350. Just need to find a dipstick that actually fits and wait for a few fittings to come in to install my transmission cooler. I had an I6 TH350 dipstick, but it didn't quite fit with all the crap on the back of my V8 (TBI motor, so has that annoying hard water pipe on the back intake manifold).

KrazyRay · 07-28-2013, 10:11 PM

I bolted the front accessories and hooked up some wires on my 87 Chevy with a 4.3. Hoping to get it running this week with the new engine.

bigd65 · 07-28-2013, 10:38 PM

Cleaned my garage. Still don't have my truck back . The guy was wet sanding the cab and fell of and fractured his shoulder.... DAMN....
Posted via Mobile Device

79Betty · 07-28-2013, 10:39 PM

I replaced my inner fenders and cleaned the windows...
Posted via Mobile Device

GM-power · 07-28-2013, 10:43 PM

Did all the drivers side weather stripping minus the vent window!!
Posted via Mobile Device

J Knight · 07-28-2013, 11:36 PM

Stripped the back half to be prostreeted. Cant post pics though.

tucsonjwt · 07-28-2013, 11:54 PM

I have been cleaning up the underside of the bed and rattle can spraying the whole underside black. Cleaned up and repainted the aluminum step bumper. Went to Phoenix to pick up a bumper with bumper guards yesterday. Went to two pick and pulls today looking for a factory jack. I learned that they get rid of all jacks immediately so that customers don't try to jack up the vehicles to assist in part removal in the yard.

So, I spotted a very nice 2001 Chrysler Sebring convertible with tan leather seats which I snagged, along with the center console. I need new seat belts in my truck, and even though it has a very nice recently rebuilt stock seat, I do like the idea of integral seat belts and more form fitting seats with built in headrests.

The Chrysler seats are a little tight for a plus size guy like me, but I think they would be better than the stock seat. The Chrysler seats have 5 bolts on each frame - 2 front, 2 back, 1 screwed into the center tunnel. Looks like just captive nut plates welded to the floor in the stock configuration. Since the bottom seat cushions are thinner than my truck seat, I think I can have a frame welded up to span the whole truck and catch the stock bolt holes, then modify the frame to accept the Chrysler bolt locations with grade 8 bolts, lock washers, and nuts.

hotrod_991 · 07-29-2013, 12:02 AM

After some searching I got my old 77 c10 back. was a father sone project that i sold a year ago. lost father in march to cancer, and needed to get it back so I tracked it down and bought back. this weekend I replaced carburator, and pulled the drive shaft out to have the carrier bearing replaced. Just enjoyed the memories and comfort of having it home again.

izzy_Britton · 07-29-2013, 12:58 AM

removed the computer controlled carb and esc distributor from my 86 c-10 and replaced them both with a Edelbrock 1406 and a Mallory clone. also removed 98% of the emissions crap, need to remove the computer and associated wiring.

long expensive weekend, i hope it is worth it.

-Izzy

Paul83 · 07-29-2013, 01:15 AM

Cleaned garage. It was a mess after working on a couple of boat and trailer projects. Pulled brackets off of an old 350 to prep and paint for the new 383 that will be dropped. Then I started on the front suspension. Replaced upper and lower ball joints. Ran out of time so that is it on the suspension. So I ordered drop shackles, this way I have work for next weekend.

PAWS 72 · 07-29-2013, 01:43 AM

Quote:

Originally Posted by hotrod_991

After some searching I got my old 77 c10 back. was a father sone project that i sold a year ago. lost father in march to cancer, and needed to get it back so I tracked it down and bought back. this weekend I replaced carburator, and pulled the drive shaft out to have the carrier bearing replaced. Just enjoyed the memories and comfort of having it home again.

Hate to hear about your Dad but atleast you got the truck back for the memories.

PAWS 72 · 07-29-2013, 01:45 AM

Went to a little church show. Didnt carry the truck but I did show the Javelin. First time it has ever been shown.The only Javelin in the area.

Still cant post pics.

Keith Seymore · 07-29-2013, 07:09 AM

Sat in the trailer at the race track in Norwalk and watched it rain...

S10Fan · 07-29-2013, 07:47 AM

Cleaned up the Heap and took her to a cruise-in. I hadn't driven her in so long some of the guys thought I'd sold her.

Tried 3 times to post a picture! #$%$#@!

tex_waco_usmc · 07-29-2013, 09:20 AM

Found that I have a rat I have to hunt down and kill! A horrible slow agonizing death to this rat! BTW, I did see him and he is the biggest rat I have seen in a very very long time! Decided to build a nest on the intake manifold over the ten days I was away in Iowa for work.

He chewed through several wires under the hood of Emi's truck. Nothing important, Windshield Wiper motor wires, ground for AC (Non-op anyways) and the secondary ground for the alternator...

The hunt is on!!!

motornut · 07-29-2013, 09:41 AM

friday-found (i think) older then 78 non-ac bezel,different texture and a radio delete...
upside down in the mud....
and a 79 cadi 427ci.....the bezel was cheaper/easier to bring home
saw my visiting brother-inlaw's father, he's got a 77 Chev camper van,since new

king-918 · 07-29-2013, 10:18 AM

Posted via Mobile Device
Replaced this timing belt
Posted via Mobile Device

king-918 · 07-29-2013, 10:21 AM

http://s1292.photobucket.com/albums/...ps4092adbb.jpg
Posted via Mobile Device

legendman · 07-29-2013, 11:04 AM

Cleaned mouse crap out of my heater box argh
Completely took it apart and washed every piece.
And put in a new heater core

INSIDIOUS '86 · 07-29-2013, 01:51 PM

Got bilstein rear shocks. Those were a huge pain to get in. Van shocks are not easy.

Lowered truck problems man
Posted via Mobile Device

Zonecone · 07-29-2013, 06:45 PM

Took off all smog crap. Cut long bed down to short bed. Fired in snow gas tanks. Took off 3" body lift. Took load control if rear brakes and re- blead brakes. Took dash apart and hooked all speakers and deck back in so I have toons. Hopefully next weekend put in drop spindles and notch frame with flip Kitt. 84 ccsb. Can't wait to be done. Well at least drive her befor complete rust free cab swap and paint.
Posted via Mobile Device

notallthere · 07-29-2013, 07:02 PM

Went to a track to learn how to do some minor stunt driving skills. Reverse 180 (rockford turn) and ebrake spins.

**brakenit** · 07-29-2013, 07:10 PM

Finished putting together the front suspension and installed the flip kit on the rear.

07-28-2013, 09:26 PM	#1
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,257	Haven't seen this lately. What did you do this weekend? Polished the wheels. Posted via Mobile Device __________________ " That didnt make it any newer " " Dont antique the equipment "

07-28-2013, 09:28 PM	#2
mongoose Registered User Join Date: Feb 2009 Location: slurrey, bc. Posts: 1,134	Re: Haven't seen this lately. What did you do this weekend? 360 nationals took up most of it.... might get out and pull the carpet today. __________________ -'73 c/10 - Low with Go - will be complete... probably never. -'90 2wd Blazer - well... soon enough anyways. -'84 SWB - the daily gas guzzler.

07-28-2013, 09:53 PM	#3
foamypirate Registered User Join Date: Apr 2009 Location: Pflugerville, TX Posts: 594	Re: Haven't seen this lately. What did you do this weekend? Dropped the 700R4 and installed a fresh TH350. Just need to find a dipstick that actually fits and wait for a few fittings to come in to install my transmission cooler. I had an I6 TH350 dipstick, but it didn't quite fit with all the crap on the back of my V8 (TBI motor, so has that annoying hard water pipe on the back intake manifold).

07-28-2013, 10:11 PM	#4
KrazyRay Registered User Join Date: Jun 2009 Location: Oroville, CA Posts: 4,827	Re: Haven't seen this lately. What did you do this weekend? I bolted the front accessories and hooked up some wires on my 87 Chevy with a 4.3. Hoping to get it running this week with the new engine.

07-28-2013, 10:38 PM	#5
bigd65 Registered User Join Date: Mar 2000 Location: Clute, TX. Posts: 1,935	Re: Haven't seen this lately. What did you do this weekend? Cleaned my garage. Still don't have my truck back . The guy was wet sanding the cab and fell of and fractured his shoulder.... DAMN.... Posted via Mobile Device __________________ 2004 Silverado Crewcab 1972 Chevy Monte Carlo 2017 Chevy Tahoe

07-28-2013, 10:39 PM	#6
79Betty Registered User Join Date: Jan 2013 Location: Jasper, IN Posts: 948	Re: Haven't seen this lately. What did you do this weekend? I replaced my inner fenders and cleaned the windows... Posted via Mobile Device __________________ When in doubt, throttle it out! 1974 Chevrolet Custom K20 2005 Ford Ranger Edge 1985 Chevrolet Custom Deluxe C10

07-28-2013, 10:43 PM	#7
GM-power Registered User Join Date: Mar 2012 Location: Little Rock, Arkansas Posts: 770	Re: Haven't seen this lately. What did you do this weekend? Did all the drivers side weather stripping minus the vent window!! Posted via Mobile Device __________________ 1979 Sierra Classic Heavy-half 1996 Silverado x-cab "the daily"

07-28-2013, 11:36 PM	#8
J Knight Registered User Join Date: Jun 2011 Location: Baytown TX Posts: 2,219	Re: Haven't seen this lately. What did you do this weekend? Stripped the back half to be prostreeted. Cant post pics though. __________________ John 82 Chevy Silverado 350ci/TH350

07-28-2013, 11:54 PM	#9
tucsonjwt Registered User Join Date: Jul 2007 Location: Tucson, AZ Posts: 3,189	Re: Haven't seen this lately. What did you do this weekend? I have been cleaning up the underside of the bed and rattle can spraying the whole underside black. Cleaned up and repainted the aluminum step bumper. Went to Phoenix to pick up a bumper with bumper guards yesterday. Went to two pick and pulls today looking for a factory jack. I learned that they get rid of all jacks immediately so that customers don't try to jack up the vehicles to assist in part removal in the yard. So, I spotted a very nice 2001 Chrysler Sebring convertible with tan leather seats which I snagged, along with the center console. I need new seat belts in my truck, and even though it has a very nice recently rebuilt stock seat, I do like the idea of integral seat belts and more form fitting seats with built in headrests. The Chrysler seats are a little tight for a plus size guy like me, but I think they would be better than the stock seat. The Chrysler seats have 5 bolts on each frame - 2 front, 2 back, 1 screwed into the center tunnel. Looks like just captive nut plates welded to the floor in the stock configuration. Since the bottom seat cushions are thinner than my truck seat, I think I can have a frame welded up to span the whole truck and catch the stock bolt holes, then modify the frame to accept the Chrysler bolt locations with grade 8 bolts, lock washers, and nuts.

07-29-2013, 12:02 AM	#10
hotrod_991 Registered User Join Date: Jul 2009 Location: Thibodaux, LA Posts: 479	Re: Haven't seen this lately. What did you do this weekend? After some searching I got my old 77 c10 back. was a father sone project that i sold a year ago. lost father in march to cancer, and needed to get it back so I tracked it down and bought back. this weekend I replaced carburator, and pulled the drive shaft out to have the carrier bearing replaced. Just enjoyed the memories and comfort of having it home again. __________________ "Buckle up I wanna try somethin!!" "of course it will hold!, I welded it!" 1977 c10 under knife for full rebuild, 5.3l 4l60e drive rain swap, replacement frame and green repaint

07-29-2013, 12:58 AM	#11
izzy_Britton Registered User Join Date: Apr 2013 Location: Nor-Cal Posts: 632	Re: Haven't seen this lately. What did you do this weekend? removed the computer controlled carb and esc distributor from my 86 c-10 and replaced them both with a Edelbrock 1406 and a Mallory clone. also removed 98% of the emissions crap, need to remove the computer and associated wiring. long expensive weekend, i hope it is worth it. -Izzy __________________ WHO_DCTC - Wifes 05 Z-71 Build - Now defunct as she decided she wants an Escalade too Cream Puff - LS'd Square - Slow going on the back burner Tripple Threat - 3 Wrecks for the price of one build thread Project Delongdium - Step-Sons Plastic Clad 2003 Avalanche - DONE and Delivered.

07-29-2013, 01:15 AM	#12
Paul83 Registered User Join Date: Dec 2012 Location: Humble, TX Posts: 171	Re: Haven't seen this lately. What did you do this weekend? Cleaned garage. It was a mess after working on a couple of boat and trailer projects. Pulled brackets off of an old 350 to prep and paint for the new 383 that will be dropped. Then I started on the front suspension. Replaced upper and lower ball joints. Ran out of time so that is it on the suspension. So I ordered drop shackles, this way I have work for next weekend. __________________ I don't care how old or gangster you think you are; if a 3 year old hands you a play phone you answer that! I like long walks on the beach, dinner by candle light, and poking dead things with a stick.

07-29-2013, 01:45 AM	#14
PAWS 72 Registered User Join Date: Nov 2011 Location: Sheffield, ALA Posts: 2,471	Re: Haven't seen this lately. What did you do this weekend? Went to a little church show. Didnt carry the truck but I did show the Javelin. First time it has ever been shown.The only Javelin in the area. Still cant post pics. Last edited by PAWS 72; 07-29-2013 at 01:52 AM.

07-29-2013, 07:09 AM	#15
Keith Seymore Registered User Join Date: May 2009 Location: Motor City Posts: 9,226	Re: Haven't seen this lately. What did you do this weekend? Sat in the trailer at the race track in Norwalk and watched it rain... __________________ Chevrolet Flint Assembly 1979-1986 GM Full Size Truck Engineering 1986 - 2019 Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926 My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524 Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/ Last edited by Keith Seymore; 07-29-2013 at 07:17 AM.

07-29-2013, 07:47 AM	#16
S10Fan Old Heap Driver Join Date: Mar 2008 Location: Newport News, Va Posts: 2,642	Re: Haven't seen this lately. What did you do this weekend? Cleaned up the Heap and took her to a cruise-in. I hadn't driven her in so long some of the guys thought I'd sold her. Tried 3 times to post a picture! #$%$#@! __________________ _____________________________ Bryan '99 Silverado 1500, 4.3, 5-speed, reg cab, short bed '50 Chevy 2DR Hard Top, 350/350, M2 Front End, 3:08 gear, cruiser. '40 F**d Sedan, all Chevy power, Heidt's front end, TCI rear, nice driver.



Register or Log In To remove these advertisements.

07-29-2013, 09:20 AM	#17
tex_waco_usmc Project Heaven in my 67!!! Join Date: Jan 2009 Location: Bosqueville, TX Posts: 899	Re: Haven't seen this lately. What did you do this weekend? Found that I have a rat I have to hunt down and kill! A horrible slow agonizing death to this rat! BTW, I did see him and he is the biggest rat I have seen in a very very long time! Decided to build a nest on the intake manifold over the ten days I was away in Iowa for work. He chewed through several wires under the hood of Emi's truck. Nothing important, Windshield Wiper motor wires, ground for AC (Non-op anyways) and the secondary ground for the alternator... The hunt is on!!!

07-29-2013, 09:41 AM	#18
motornut 78K & 79C Jimmys Join Date: Nov 2009 Location: Ottawa Ont CANADA Posts: 7,901	Re: Haven't seen this lately. What did you do this weekend? friday-found (i think) older then 78 non-ac bezel,different texture and a radio delete... upside down in the mud.... and a 79 cadi 427ci.....the bezel was cheaper/easier to bring home saw my visiting brother-inlaw's father, he's got a 77 Chev camper van,since new __________________ John 1978 GMCJimmy4X4-350/203 1979 GMCJimmy4X2-305/350

07-29-2013, 10:18 AM	#19
king-918 Registered User Join Date: Nov 2011 Location: Oklahoma City Oklahoma Posts: 1,056	Re: Haven't seen this lately. What did you do this weekend? Posted via Mobile Device Replaced this timing belt Posted via Mobile Device __________________ <----Christopher My Tardis Oh yeah I'm really a Toyota guy, but had some stuff sitting around. Oklahoma

07-29-2013, 10:21 AM	#20
king-918 Registered User Join Date: Nov 2011 Location: Oklahoma City Oklahoma Posts: 1,056	Re: Haven't seen this lately. What did you do this weekend? http://s1292.photobucket.com/albums/...ps4092adbb.jpg Posted via Mobile Device __________________ <----Christopher My Tardis Oh yeah I'm really a Toyota guy, but had some stuff sitting around. Oklahoma

07-29-2013, 01:51 PM	#22
INSIDIOUS '86 Registered User Join Date: Jul 2009 Location: washington Posts: 4,178	Re: Haven't seen this lately. What did you do this weekend? Got bilstein rear shocks. Those were a huge pain to get in. Van shocks are not easy. Lowered truck problems man Posted via Mobile Device __________________ 377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511

07-29-2013, 06:45 PM	#23
Zonecone Registered User Join Date: Mar 2013 Location: Templeton ca Posts: 22	Re: Haven't seen this lately. What did you do this weekend? Took off all smog crap. Cut long bed down to short bed. Fired in snow gas tanks. Took off 3" body lift. Took load control if rear brakes and re- blead brakes. Took dash apart and hooked all speakers and deck back in so I have toons. Hopefully next weekend put in drop spindles and notch frame with flip Kitt. 84 ccsb. Can't wait to be done. Well at least drive her befor complete rust free cab swap and paint. Posted via Mobile Device

07-29-2013, 07:02 PM	#24
notallthere Registered User Join Date: Nov 2011 Location: sarnia ontario canada Posts: 211	Re: Haven't seen this lately. What did you do this weekend? Went to a track to learn how to do some minor stunt driving skills. Reverse 180 (rockford turn) and ebrake spins.

07-29-2013, 07:10 PM	#25
brakenit Active Member Join Date: Mar 2004 Location: Indiana Posts: 198	Re: Haven't seen this lately. What did you do this weekend? Finished putting together the front suspension and installed the flip kit on the rear.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.