OR Volt Gauge Conversion Kits

[TBONE1964]

Hello all,

I have 2 volt gauge conversions ready for sale if interested. They are $100.00 plus shipping which is $15.00 within CON US. Please inquire if not in the CON US for shipping quote.

Thank you for the interest,
Tom

[Already Gone]

Originally Posted by TBONE1964

Hi Greg,

Very sorry for the delay. If you have a volt meter on the battery while running, you should get say 14.5 or so volts. That would be with a good alternator output at idle. I use a 12 v battery charger set on 10 amps which gives me about 12.5 volts and that is where I set the needle. It is possible the needle slipped or I was in a brain fart mode that day and placed it wrong.

What I see in your photo should be about 15.5 which seems a little high. Did you check it at the battery? Make sure your regulator is not sticking and causing an over charge condition.

If you believe that the volt gauge conversion is in accurate, you can send it back to me for an adjustment or I can send you just the gauge that is set up correctly and you can just swap it.

Let me know what you would like to do. I will accommodate you and make this right. By the way, no charge to you.

Thank you,
Tom

I didn't think it was inaccurate I just wanted to make sure it was working as it should. Since I sent this I have verified the your gauge is working as it should..

[VWNate1]

Hard to find good customer service like this these days Tom .

[Edmond]

Hi Tom,

Just found this thread while searching for something completely different 😊
Anyway, I wanted to know if you still sell these conversion kits?
If so, could you give me an estimate on shipping to the Netherlands?
Thanks in advance.

[TBONE1964]

Originally Posted by Edmond

Hi Tom,

Just found this thread while searching for something completely different 😊
Anyway, I wanted to know if you still sell these conversion kits?
If so, could you give me an estimate on shipping to the Netherlands?
Thanks in advance.

Sure thing, If you can send me a PM with your complete shipping address, I can figure a quote and go from there.

Thank you for the interest,
Tom

[Edmond]

Hi Tom,

PM sent.
Thank you. 👍

[dflarsen77]

Sent you a PM tbone

[TBONE1964]

I have this volt gauge conversion ready to sell.

It will come with the wiring and instructions to install.

$100.00 or $115.00 shipped in med flat rate box with in CON US

Outside of CON US, I can quote shipping.

More kits will be done soon. Waiting for supplies.

Thank you ,
Tom

[MySons68C20]

Hi Tom, I will contact you tomorrow to purchase the gauge kit shown above.
Thanks.

Blake

[MySons68C20]

Email sent

Blake

[TBONE1964]

Originally Posted by MySons68C20

Email sent

Blake

Thank you Blake,

I appreciate your business,
Tom

[Stephen717]

instead of running a hot leg between the temp and volt gauge could I leave part of my circuit board in place and tape the other part back?

[TBONE1964]

[QUOTE=Stephen717;8372064]instead of running a hot leg between the temp and volt gauge could I leave part of my circuit board in place and tape the other part back?[/QUOTE

If you are referring to the amp gauge portion of the circuit board, they are both live. If you trace it back to the connector, you could actually wire your hot into the number one or twelve location on the connector. For the other side, that does not get used by the volt gauge. If you have amp gauge wiring correctly, either number one or twelve can be de pinned so no power passes through. That way you can wire the volt gauge with the circuit board.

You can run power to the volt gauge by any means you feel acceptable for your purpose. As long as it has battery voltage an ground, it will work.

One reason I like to tag off the temp gauge is for trouble shooting. If the user has a failure of a volt gauge, the question is does the temp gauge and fuel gauge still work. They all share power. if they all fail, then it is a different approach to diagnose.

I provide everything needed to swap this into your truck and have a source to wire it.

Hope this helps,

Tom

[tchevs]

Great work Tom. Payment sent

[TBONE1964]

Originally Posted by tchevs

Great work Tom. Payment sent

Thank you Tony. Very happy with our transactions and most important to me is you are happy with everything.

[TBONE1964]

I have 3 kits ready to ship.

As always, I can only put these together as fast as I can get parts needed.

I am always out of one main ingredient it seems

Thanks to all,
Tom

[Black71Shorty]

Tom, I’ll take one with the overlay.

Thanks
Coby

[TBONE1964]

Originally Posted by Black71Shorty

Tom, I’ll take one with the overlay.

Thanks
Coby

Thank you Coby,

PM on the way.

[TBONE1964]

Originally Posted by Black71Shorty

Tom, I’ll take one with the overlay.

Thanks
Coby

You should see your conversion kit on the 15th Coby. Let me know if not and I will track it.

I appreciate it,

Tom

[TBONE1964]

Had three, sold one, built one and still have three up for grabs

Thank you,
Tom

[Black71Shorty]

Originally Posted by TBONE1964

You should see your conversion kit on the 15th Coby. Let me know if not and I will track it.

I appreciate it,

Tom

Hey Tom, I appreciate the update! I’ll keep a lookout for it!

Thanks again
Coby

[TBONE1964]

Holiday weekend bump.

I have some ready to ship

[Black71Shorty]

Tom, I received mine the other day. Very nice! Look forward to getting it put in.

Thanks again
Coby

[Nicks33]

Morning Tom, will you sell a voltmeter overlay decal only? Thanks, Nick

[TBONE1964]

Originally Posted by Nicks33

Morning Tom, will you sell a voltmeter overlay decal only? Thanks, Nick

I am sorry but I need to keep my inventory for the kits. I cannot build a kit with out them and I never know when I will not be able to get more overlays.

Thank you,
Tom