The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > LSx Swaps

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-17-2017, 08:27 PM   #1
Sean1985
Registered User
 
Sean1985's Avatar
 
Join Date: Dec 2013
Location: Carlsbad
Posts: 133
Dakota digital/Gm controller OBD2 issues.

I have an ls3 with a gm controller in my 67. I have the Dakota digital bim module that connects to the obd2 port that feeds my tach and coolant temp. Every time my electric fans kick on I loose the signal from the ecu? The bim module doesn't loose voltage. This just started recently. It haven't always done this. I talked to Dakota digital and they said the module either works or it doesn't.
Has anyone had this issue. It has a brand new battery and I'm not having any kind of crazy draw on the battery. It has to be some sort of signal from the ecu? I appreciate any feedback.
Sean1985 is offline   Reply With Quote
Old 07-18-2017, 08:40 AM   #2
Hart_Rod
*************
 
Hart_Rod's Avatar
 
Join Date: Apr 2005
Location: Pensacola, FL
Posts: 17,858
Re: Dakota digital/Gm controller OBD2 issues.

I would recheck all of my grounds.
Hart_Rod is offline   Reply With Quote
Old 07-18-2017, 11:32 PM   #3
clinebarger
Senior Member
 
Join Date: May 2009
Location: Fort Worth, TX
Posts: 6,370
Re: Dakota digital/Gm controller OBD2 issues.

How are the Fans/Fan Relays wired?
clinebarger is offline   Reply With Quote
Old 07-19-2017, 09:42 AM   #4
Sean1985
Registered User
 
Sean1985's Avatar
 
Join Date: Dec 2013
Location: Carlsbad
Posts: 133
Re: Dakota digital/Gm controller OBD2 issues.

They wire right off the fuse box that's provided in the gm harness. It's controlled by the ecu. It's a crate ls3 and a gm harness. So they leave a pigtail for the fan to splice onto. And the ground is connected to the same ground as the chassis, and everything else. I think next I'm going to look at the fuse box relays, and fuses. I know these fans draw a lot of current.
Sean1985 is offline   Reply With Quote
Old 07-19-2017, 01:07 PM   #5
knomadd
Registered User
 
knomadd's Avatar
 
Join Date: Jul 2012
Location: Rosenberg, Texas
Posts: 3,506
Re: Dakota digital/Gm controller OBD2 issues.

I'm sure your Dakota Digital box isn't grounded to the same ground on the chassis. You'll want to check ALL of your grounds to be sure. The relays might be a good place to look too, but intermittent things can often be traced back to a bad ground somewhere, especially if it didn't start out with the problem. Otherwise, just a guess, it might be something to do with the signal you're getting form your DLC to the BIM module.

Also, check to see if your fan wiring is secured in place and hasn't rubbed through causing a short of some-sort.
__________________
-Duane

C/10 Club Texas member
1971 Chevy C10 "Brutus" SWB Fleetside 2016 6.0L (L96) 6L90E (driver/project)
1965 Pontiac GTO "Royal Goat" 400/TH400 w/AC (my baby)
knomadd is offline   Reply With Quote
Old 07-19-2017, 01:17 PM   #6
Sean1985
Registered User
 
Sean1985's Avatar
 
Join Date: Dec 2013
Location: Carlsbad
Posts: 133
Re: Dakota digital/Gm controller OBD2 issues.

Yea I've checked every ground so I'm assuming it's from the dlc connection. I think I might scrap that and tap off individually to get my tach signal to be 100% sure.
Sean1985 is offline   Reply With Quote
Old 07-19-2017, 01:21 PM   #7
Sean1985
Registered User
 
Sean1985's Avatar
 
Join Date: Dec 2013
Location: Carlsbad
Posts: 133
Re: Dakota digital/Gm controller OBD2 issues.

Plus why would I loose a ground when only the fans kick on. When the fans aren't on everything works fine. Just thinking out loud.
Sean1985 is offline   Reply With Quote
Old 07-19-2017, 02:02 PM   #8
knomadd
Registered User
 
knomadd's Avatar
 
Join Date: Jul 2012
Location: Rosenberg, Texas
Posts: 3,506
Re: Dakota digital/Gm controller OBD2 issues.

Quote:
Originally Posted by Sean1985 View Post
Yea I've checked every ground so I'm assuming it's from the dlc connection. I think I might scrap that and tap off individually to get my tach signal to be 100% sure.
Are you using the BIM module for just tach and coolant temp? Are you losing both (everything) or just the tach signal?

Quote:
Originally Posted by Sean1985 View Post
Plus why would I loose a ground when only the fans kick on. When the fans aren't on everything works fine. Just thinking out loud.

If it's loose, or if it's not a good clean ground, the fans could possibly jolt the ground loose, or cause a load that cannot overcome an inefficient/poor quality ground. Or, maybe the fans are the problem? Again, guessing with the fans.
__________________
-Duane

C/10 Club Texas member
1971 Chevy C10 "Brutus" SWB Fleetside 2016 6.0L (L96) 6L90E (driver/project)
1965 Pontiac GTO "Royal Goat" 400/TH400 w/AC (my baby)
knomadd is offline   Reply With Quote
Old 07-19-2017, 02:44 PM   #9
Sean1985
Registered User
 
Sean1985's Avatar
 
Join Date: Dec 2013
Location: Carlsbad
Posts: 133
Re: Dakota digital/Gm controller OBD2 issues.

Quote:
Originally Posted by knomadd View Post
Are you using the BIM module for just tach and coolant temp? Are you losing both (everything) or just the tach signal?




If it's loose, or if it's not a good clean ground, the fans could possibly jolt the ground loose, or cause a load that cannot overcome an inefficient/poor quality ground. Or, maybe the fans are the problem? Again, guessing with the fans.
I'm using the bim for both tach and coolant. And yes I'm loosing both. My ground for the fans is the same ground for the fuse box. I daisy chained the ground from battery to motor to chassis to cab. So technically the ground is paralleled through the entire truck.

I think I'm going to disconnect the bim and put a meter on the signal for coolant. That should increase in voltage as temp goes up. And then see if I loose voltage when fans kick on. Then I know it's coming from the ecu. Or too many amps from fans. But not blowing a fuse. Hahaha. Oh the fun of trouble shooting. As if I don't do this enough on elevators.
Sean1985 is offline   Reply With Quote
Old 07-19-2017, 04:42 PM   #10
knomadd
Registered User
 
knomadd's Avatar
 
Join Date: Jul 2012
Location: Rosenberg, Texas
Posts: 3,506
Re: Dakota digital/Gm controller OBD2 issues.

I wish I could be of some help. Good luck!
__________________
-Duane

C/10 Club Texas member
1971 Chevy C10 "Brutus" SWB Fleetside 2016 6.0L (L96) 6L90E (driver/project)
1965 Pontiac GTO "Royal Goat" 400/TH400 w/AC (my baby)
knomadd is offline   Reply With Quote
Old 07-19-2017, 04:55 PM   #11
Sean1985
Registered User
 
Sean1985's Avatar
 
Join Date: Dec 2013
Location: Carlsbad
Posts: 133
Re: Dakota digital/Gm controller OBD2 issues.

Quote:
Originally Posted by knomadd View Post
I wish I could be of some help. Good luck!
I appreciate the help!
Sean1985 is offline   Reply With Quote
Old 07-26-2017, 03:35 PM   #12
knomadd
Registered User
 
knomadd's Avatar
 
Join Date: Jul 2012
Location: Rosenberg, Texas
Posts: 3,506
Re: Dakota digital/Gm controller OBD2 issues.

Did you figure anything out?
__________________
-Duane

C/10 Club Texas member
1971 Chevy C10 "Brutus" SWB Fleetside 2016 6.0L (L96) 6L90E (driver/project)
1965 Pontiac GTO "Royal Goat" 400/TH400 w/AC (my baby)
knomadd is offline   Reply With Quote
Old 07-26-2017, 10:33 PM   #13
Sean1985
Registered User
 
Sean1985's Avatar
 
Join Date: Dec 2013
Location: Carlsbad
Posts: 133
Re: Dakota digital/Gm controller OBD2 issues.

Quote:
Originally Posted by knomadd View Post
Did you figure anything out?

I had a fuseable link that wasn't letting 12vdc pass. It was like 11 and some change of even a little less. So the voltage drop was too much for the bim. But everything else was working fine. I had the same voltage running to all the Dakota digital gauges. Weird. But got it fixed. Thanks for the help!!
Sean1985 is offline   Reply With Quote
Old 07-27-2017, 11:47 AM   #14
knomadd
Registered User
 
knomadd's Avatar
 
Join Date: Jul 2012
Location: Rosenberg, Texas
Posts: 3,506
Re: Dakota digital/Gm controller OBD2 issues.

That does sound weird. Glad you got it fixed!
__________________
-Duane

C/10 Club Texas member
1971 Chevy C10 "Brutus" SWB Fleetside 2016 6.0L (L96) 6L90E (driver/project)
1965 Pontiac GTO "Royal Goat" 400/TH400 w/AC (my baby)
knomadd is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:24 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com