Trim and Emblem removal - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bgray · 08-21-2017, 01:40 PM

Hey guys, here is my blazer.

Questions, i need to remove the Cheyenne badge on the rear quarter, and the tailgate rear trim panel for some work. How does these come off?

Haven't been able to find any info online.

Thanks guys,

Brandon

74CustomK20 · 08-21-2017, 03:14 PM

Speed nuts on the back, like the front end grill trim. Idk how to access em because I've never had a blazer.

bbbc10 · 08-21-2017, 06:21 PM

comes off the same way truck does just unscrew from the inside

**jlmerie** · 08-21-2017, 06:36 PM

I am not sure. If you are talking about the round Cheyenne emblems on both rear quarters, I believe those are a press fit. I don't know all the correct terminology, but there are "keepers" inserted into the hole in the quarter panel and the pins from the emblem are held in place by the "keepers". Maybe this picture will help. I believe this is unique to the Blazers (and Jimmys). Really nice Blazer by the way!

**Willowrun** · 08-21-2017, 10:16 PM

For the round emblems pull the rear taillight assemblies and take a look in there. If it hasn't been removed before you will see some small, pressed sheetmetal nuts attached to the studs on the emblem. Take those off to remove emblem.

On the tailgate pull the inspection cover off of the inside of the tailgate, roll window out about 1/2 way and you will see the nuts to remove to remove tailgate trim.

**1774btcrew** · 08-22-2017, 10:04 AM

The round emblems use barrel clips(these are basically spring steel that expands as you push the emblem in and then holds tension on it) Those emblems need carefully pryed off. Ford was known for using this type of clip on almost all of there emblems. This is about the only application GM used them for that I have seen

bgray · 08-22-2017, 10:15 AM

thanks very much for the help everyone!

**TKCR** · 08-22-2017, 12:20 PM

That is a NICE LOOKING Blazer!!

frenchy51 · 08-22-2017, 06:33 PM

Beautiful Blazer! Be very careful pulling the side emblems. Use a plastic trim removal tool or some plastic item like that or you'll scratch that beautiful paint for sure. go slowly working all around it little by little and protect the paint with masking tape. The tailgate trim has speed nuts on the inside-so that's safer.

08-21-2017, 01:40 PM	#1
bgray Registered User Join Date: Aug 2012 Location: burlington ontario Posts: 15	Trim and Emblem removal Hey guys, here is my blazer. Questions, i need to remove the Cheyenne badge on the rear quarter, and the tailgate rear trim panel for some work. How does these come off? Haven't been able to find any info online. Thanks guys, Brandon

08-21-2017, 03:14 PM	#2
74CustomK20 Registered User Join Date: Oct 2014 Location: Tell City, IN Posts: 637	Re: Trim and Emblem removal Speed nuts on the back, like the front end grill trim. Idk how to access em because I've never had a blazer. __________________ Big Nate Carp. Local 224. Buy made in the USA! 03 F350 6.0 Daily Race Truck. 79 C70 366 Project Dump.

08-21-2017, 06:21 PM	#3
bbbc10 Diggin The SquareLife Join Date: Dec 2010 Location: garland,tx Posts: 1,933	Re: Trim and Emblem removal comes off the same way truck does just unscrew from the inside

08-21-2017, 06:36 PM	#4
jlmerie Registered User Join Date: Sep 2005 Location: Colorado Posts: 1,077	Re: Trim and Emblem removal I am not sure. If you are talking about the round Cheyenne emblems on both rear quarters, I believe those are a press fit. I don't know all the correct terminology, but there are "keepers" inserted into the hole in the quarter panel and the pins from the emblem are held in place by the "keepers". Maybe this picture will help. I believe this is unique to the Blazers (and Jimmys). Really nice Blazer by the way! Attached Images __________________ James

08-21-2017, 10:16 PM	#5
Willowrun Senior Member Join Date: Mar 2013 Location: Ann Arbor, MI Posts: 1,029	Re: Trim and Emblem removal For the round emblems pull the rear taillight assemblies and take a look in there. If it hasn't been removed before you will see some small, pressed sheetmetal nuts attached to the studs on the emblem. Take those off to remove emblem. On the tailgate pull the inspection cover off of the inside of the tailgate, roll window out about 1/2 way and you will see the nuts to remove to remove tailgate trim.

08-22-2017, 10:04 AM	#6
1774btcrew Senior Member Join Date: Jun 2009 Location: Phoenix AZ Posts: 4,603	Re: Trim and Emblem removal The round emblems use barrel clips(these are basically spring steel that expands as you push the emblem in and then holds tension on it) Those emblems need carefully pryed off. Ford was known for using this type of clip on almost all of there emblems. This is about the only application GM used them for that I have seen __________________ AZPartsLocators on Instagram 1972 Cheyenne Super Short Bed big block "Blackie" 1977 Crew Cab GMC Short bed with 4BT Intercooled Cummins Diesel and a 4L80e "The Junkyard Dog" 1985 Crew Cab Chevy dually with 5.9 Cummins "The Big Dog" This is what my dad liked to be called by the grandkids before he passed so it seems fitting for his old truck.

08-22-2017, 10:15 AM	#7
bgray Registered User Join Date: Aug 2012 Location: burlington ontario Posts: 15	Re: Trim and Emblem removal thanks very much for the help everyone!

08-22-2017, 12:20 PM	#8
TKCR Senior Member Join Date: Oct 2014 Location: Ohio Posts: 6,979	Re: Trim and Emblem removal That is a NICE LOOKING Blazer!! __________________ FB Page for my Seats Belts https://www.facebook.com/73-87-Chevy...9439407476735/ Restoring Seatbelts: http://67-72chevytrucks.com/vboard/s...d.php?t=809750 SOLD My 86 Build:http://67-72chevytrucks.com/vboard/s...d.php?t=654972 Past Restored Bench Seats:http://67-72chevytrucks.com/vboard/s...d.php?t=715398 PayPal link to pay for your items: https://www.paypal.me/TKCR

08-22-2017, 06:33 PM	#9
frenchy51 Registered User Join Date: Jun 2014 Location: Orland, Nor-Cal Posts: 617	Re: Trim and Emblem removal Beautiful Blazer! Be very careful pulling the side emblems. Use a plastic trim removal tool or some plastic item like that or you'll scratch that beautiful paint for sure. go slowly working all around it little by little and protect the paint with masking tape. The tailgate trim has speed nuts on the inside-so that's safer. __________________ 1972 Highlander PAC B 400BB-SOLD 1974 K5 Blazer-6.0 swap 1974 C20 Long Bed 454 1977 GMC HeavyHalf several adopted orphans

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.