AL Cutting up 65 cab

[Mack B]

Cab is rusty in all the usual places, but if you happen to need an uncommon piece or section I may can help you out. I just don’t want to scrap anything that someone may be able to use. $15.00+shipping per section. I’ll gladly take pictures of anything you need, if you see any thing else of interest just ask. I will probably not be able to cut any areas until weekends. Thanks for looking!

[DPowers]

Sail panels?

[Mack B]

Originally Posted by DPowers

Sail panels?

There is one, but the finish on it is horrendous. I don't think its salvageable.

[ScottH]

can u post a pic of the center hump?

thanks

[pimpston65]

how bout both A pliars? can you cut the whole section from the bottom hinge hole area down. including both inside and outside the cab?

[pimpston65]

all this area.

[MikeG.]

Dash ?

[Mack B]

Originally Posted by pimpston65

all this area.

Absolutely. It’s not perfect. There is some rust at the seam where the rocker meets the pillar. The kickpanel area inside is non existent.

[Mack B]

Originally Posted by MikeG.

Dash ?

It’s got rust in the corners

[Mack B]

Originally Posted by ScottH

can u post a pic of the center hump?

thanks

Absolutely!

[pimpston65]

Originally Posted by Mack B

Absolutely. It’s not perfect. There is some rust at the seam where the rocker meets the pillar. The kickpanel area inside is non existent.

thank you for the photos. shes a bit too rough for my project...

[Mack B]

Originally Posted by pimpston65

thank you for the photos. shes a bit too rough for my project...

I figured they would be, believe it or not this was a nice truck 20 years ago.
Thanks for your interest either way!

[jasons]

I'd take the center section of the dash. How much to ship to zip 68924?

[Mack B]

Originally Posted by jasons

I'd take the center section of the dash. How much to ship to zip 68924?

While not completely hacked up, the radio hole has been trimmed about an 1/8” see pic. If this isn’t a deal breaker tell me how much of the dash you want and I’ll get you a quote.

[DPowers]

Originally Posted by Mack B

There is one, but the finish on it is horrendous. I don't think its salvageable.

So the one on the cab and the one in the floor of the cab are the same?
I may still be interested pending pics when you get the time.
My email is dwanepowers@att.net if that is easier.

[Mack B]

Originally Posted by DPowers

So the one on the cab and the one in the floor of the cab are the same?
I may still be interested pending pics when you get the time.
My email is dwanepowers@att.net if that is easier.

No sir, the one in the cab was the earlier style and someone cut the portion that wraps around the cab off....with an axe it appeared I couldn’t find it but pretty sure it’s been recycled.

The passenger side one is in better shape than I remember. It’s straight, but does have pretty deep scratches around the bottom. $30.00+shipping?

Edit: I’m wrong there was a third sail panel, that was different and butchered. The one in the cab was the right style but was cut up as well....still gone eitherway.

[DPowers]

Thanks, but the best I could do would be $25.00 shipped. If the rectangular brackets that are on the cab are there, I would do go $30 shipped for the brackets and the one sail panel.

[ScottH]

would u b willing to cut out & ship the center hump?

[Mack B]

Originally Posted by ScottH

would u b willing to cut out & ship the center hump?

Yes sir, the pic didn't show up as sharp as I hoped. The area under the gas pedal has rusted through, the passenger side is soft in that area as well. If those areas don't matter to you, just show me where you want it cut.

[Mack B]

Originally Posted by DPowers

Thanks, but the best I could do would be $25.00 shipped. If the rectangular brackets that are on the cab are there, I would do go $30 shipped for the brackets and the one sail panel.

I need the brackets for my project, but I will get the panel to your door for $30.00

[ScottH]

Appreciate ur help on this. The easiest way would be from the open seam to where it ends under the seat. On the sides if u could cut it where it meets the flat floor area on both sides that should work. LMK if that isnt clear & what u need for the patch.

Thanks
Scott

[aotte1]

Interest in big back window section, condition and pics of it.
What price do you want?

Les

[MikeG.]

I want the Whole dash from door to door

[fredhlynch2]

Need bracket and pedals for the brake and clutch. Zip code is 54935

[jasons]

Originally Posted by Mack B

While not completely hacked up, the radio hole has been trimmed about an 1/8” see pic. If this isn’t a deal breaker tell me how much of the dash you want and I’ll get you a quote.

I think I can work with that. I'd take from the instrument panel opening to the glove box opening and a few inches on the top. Kind of like this, a couple more inches to each side would be good.