Pulling motor question - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Steeveedee** · 11-04-2020, 10:28 PM

Putting a load on it does not mean lugging the engine, BTW. That's a sure way to lose lower end bearings.

Asshat · 11-06-2020, 12:39 AM

I forgot where this goes - could someone give me a hint?

Edit: I think this is for the wiper blade section.

**The Rocknrod** · 11-06-2020, 02:33 PM

Hood brace.

Asshat · 11-06-2020, 02:43 PM

Quote:

Originally Posted by The Rocknrod

Hood brace.

Oh, yeah - now I remember.

Thanks!!

Asshat · 11-20-2020, 10:54 PM

Seems to have some noise coming from the pulley. Not sure if it is the harmonic balancer or something else.

https://youtu.be/3Ks6V5pGDu4

**Steeveedee** · 11-20-2020, 11:40 PM

Not the balancer. How tight is the belt? Take the adjustment off the fan belt and turn the components by hand to make sure that the water pump or the alternator aren't giving too much resistance.

Desert dog · 11-21-2020, 01:27 PM

For a quick check of the balancer, place a mark on the face of it across the the rubber damper portion and then run it. The mark should stay aligned.

11-04-2020, 10:28 PM	#76
Steeveedee Who Changed This? Join Date: Jan 2013 Location: Simi Valley, CA Posts: 10,698	Re: Pulling motor question Putting a load on it does not mean lugging the engine, BTW. That's a sure way to lose lower end bearings. __________________ ~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA

11-06-2020, 12:39 AM	#77
Asshat Registered User Join Date: Jul 2015 Location: South Orange County CA Posts: 1,265	Re: Pulling motor question I forgot where this goes - could someone give me a hint? Edit: I think this is for the wiper blade section. Attached Images __________________ 1963 C20, small window, long bed 292, 4-speed Last edited by Asshat; 11-06-2020 at 11:56 AM.

11-06-2020, 02:33 PM	#78
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: Pulling motor question Hood brace. __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

11-20-2020, 10:54 PM	#80
Asshat Registered User Join Date: Jul 2015 Location: South Orange County CA Posts: 1,265	Re: Pulling motor question Seems to have some noise coming from the pulley. Not sure if it is the harmonic balancer or something else. https://youtu.be/3Ks6V5pGDu4 __________________ 1963 C20, small window, long bed 292, 4-speed

11-20-2020, 11:40 PM	#81
Steeveedee Who Changed This? Join Date: Jan 2013 Location: Simi Valley, CA Posts: 10,698	Re: Pulling motor question Not the balancer. How tight is the belt? Take the adjustment off the fan belt and turn the components by hand to make sure that the water pump or the alternator aren't giving too much resistance. __________________ ~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA

11-21-2020, 01:27 PM	#82
Desert dog Registered User Join Date: Aug 2020 Location: Tucson, AZ Posts: 51	Re: Pulling motor question For a quick check of the balancer, place a mark on the face of it across the the rubber damper portion and then run it. The mark should stay aligned.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.