|
08-27-2024, 06:21 PM
|
#76 |
|
Senior Member
 
Join Date: Sep 2018
Location: Belmont OH
Posts: 295
|
Re: 1950 Hudson Pacemaker
It has been quite sometime since I have posted in this thread. Today I picked up a 5.3/4L60E combo for the Hudson. Neighbor down the street is going to scrap his 2005 GMC Sierra because the frame is rotted. Traded him the Inline 6 flathead/3spd OD trans out of the Hudson. Tomorrow we are going to pick what we can from the truck before it gets hauled off. Thursdays plan is to make a trip to U-pull it and get an 8.8 rear end from a Ford Ranger to replace the Hudson rear end and that should be enough drive train pieces to keep me busy over the winter.
|
|
|
|
08-27-2024, 09:50 PM
|
#77 |
|
Proprietor of Dale's Corner
Join Date: Nov 2012
Location: Vacaville , CA
Posts: 16,245
|
Re: 1950 Hudson Pacemaker
The plan sounds great. It's also great to see progress!!
__________________
"Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man R.I.P. FleetsidePaul |
|
|
|
|
08-28-2024, 02:45 PM
|
#78 |
|
Senior Member
Join Date: Sep 2018
Location: Belmont OH
Posts: 295
|
Re: 1950 Hudson Pacemaker
Todays harvest of the donor vehicle consisted of the tilt steering column with harness and fuse box, and the HVAC unit complete with ductwork and wiring.
|
|
|
|
|
08-29-2024, 10:46 PM
|
#79 |
|
Senior Member
Join Date: Sep 2018
Location: Belmont OH
Posts: 295
|
Re: 1950 Hudson Pacemaker
The trip to U-pull it today did not disappoint and was a huge success. Picked up a hydroboost unit with MC, pedal, and brake light switch out of a 2004 Express 2500 van. Also found an 8.8 disc brake rear end out of a 2011 Ranger with 4.10 gears.
|
|
|
|
|
08-30-2024, 11:11 PM
|
#80 |
|
The Older Generation
  
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,777
|
Re: 1950 Hudson Pacemaker
-
Pretty soon you will have the whole yard home....  I like the car. It will make a great cruiser!
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
|
|
|
12-07-2024, 05:24 PM
|
#81 |
|
Senior Member
Join Date: Sep 2018
Location: Belmont OH
Posts: 295
|
Re: 1950 Hudson Pacemaker
Today I changed the oil pan on the 5.3 and set the motor and transmission into the Hudson to start on mock up. Fits in there like it was factory lol
|
|
|
|
|
12-12-2024, 10:11 PM
|
#82 | |
|
The Older Generation
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,777
|
Re: 1950 Hudson Pacemaker
Quote:
Well, almost factory....  ... Looks like you are making progress on it so that's good.
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
