PO has me PO'd - Page 124 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**zicc1835** · 06-29-2019, 08:46 AM

ahh DUNCAN YoYo been there done that wish I had saved one I too shall be a spring chicken August 17th turning 68 years young...Happy Birthday Jim
Jess

**jaros44sr** · 07-01-2019, 07:22 AM

Quote:

Originally Posted by zicc1835

ahh DUNCAN YoYo been there done that wish I had saved one I too shall be a spring chicken August 17th turning 68 years young...Happy Birthday Jim
Jess

Wow Jess, I am 2 days older than you, Happy Birthday to you as well

Us spring chickens have got to get together

**jaros44sr** · 07-04-2019, 06:43 AM

tank is mounted in truck, filler neck hose installed. What a pita putting tank up even with a trans jack

seems the repop manufactorer coundn't measure, as the mounting holes for the "U" bracket were off by a 1/4", didn't have a tool to do the job quickly so I just grabbed a rat tail file, and made a bunch of noise

Later will install rubber, between tank and straps.

also, received a filler neck clamp from Eric(1972 jimmy). Didn't even know they had a clamp

**jaros44sr** · 07-05-2019, 08:01 AM

[url=https://flic.kr/p/2gr67p1]20190704_123833

[url=https://flic.kr/p/2gr6dyW]20190704_123548

**jaros44sr** · 07-05-2019, 08:07 AM

finally was able to use my wobbler/center finder I bought several months ago

[url=https://flic.kr/p/2gpEbJe]20190702_135842

**jaros44sr** · 07-05-2019, 11:48 AM

Poser

[url=https://flic.kr/p/2grJWWm]20190705_113337

**jaros44sr** · 07-06-2019, 10:52 AM

oil pan is up,but not without a struggle. My all thread didn't work as planned, the back corners hit the all thread, but the front was ok. I've bought 2 of these gaskets and neither on came with those 4 gizmos that help with installation
I have to open up the holes in the clamps for 1/4-20 studs. I have a press / punch with dies, want to see if it works on SS, I have to find the pliers that close these clamps

[url=https://flic.kr/p/2gspivY]20190706_101712

[url=https://flic.kr/p/2gsp2LF]20190706_101726

[url=https://flic.kr/p/2gsp48J]20190706_101800

rsavage · 07-06-2019, 11:38 AM

I always glue the gaskets, even the one piece, to the pan with black RTV and let it sit for a few hours or overnight. I put the pan bolts down through the holes to keep them aligned, and also use some blue tape. Gasket stays on the pan whether it is upside down when installing on an engine stand or when putting it on the engine when it is in the truck.

It's looking good Jim.

AJs72K5 · 07-06-2019, 02:18 PM

The one piece gaskets don't need any glue or RTV. Just make sure the block and all mating surfaces are clean and bone dry.

Here's the Snap-ups you're talking about. Don't know how I put up a pan and gaskets before without them. Huge difference.

https://www.summitracing.com/parts/fel-es72863

rsavage · 07-06-2019, 07:00 PM

Quote:

Originally Posted by AJs72K5

The one piece gaskets don't need any glue or RTV. Just make sure the block and all mating surfaces are clean and bone dry.

Here's the Snap-ups you're talking about. Don't know how I put up a pan and gaskets before without them. Huge difference.

https://www.summitracing.com/parts/fel-es72863

Of course they don't. But gluing them to the pan with a very thin smooth layer of RTV works flawlessly and holds the gasket in place all over its perimeter. It will also stay with the pan if you have to remove it.

rsavage · 07-06-2019, 08:28 PM

By the way Jim, what is the capacity of that pan?

**jaros44sr** · 07-07-2019, 07:42 AM

thanks for your ideas guys, but I sorta went with both, just RTV'D the 4 corners where it made a sharp bend. ran my primer device yesterday and no leaks so far. But, who knows what will happen when the engine gets up to temp. and full pressure.

the pan is a 8 quart, just a heads up, they didn't deburr inside where it was cut and welded so be careful when you wipe it down

[url=https://flic.kr/p/2grFkpA]20190705_095016

thanks for the link on the parts AJ. I just may buy them and keep in tool box

**zicc1835** · 07-08-2019, 10:34 PM

Quote:

Originally Posted by jaros44sr

Wow Jess, I am 2 days older than you, Happy Birthday to you as well

Us spring chickens have got to get together

we shall ...I may have more time on my hands soon ....and take a ride when it works for us ....share a birthday cheer...

**jaros44sr** · 07-11-2019, 08:13 AM

Quote:

Originally Posted by zicc1835

we shall ...I may have more time on my hands soon ....and take a ride when it works for us ....share a birthday cheer...

Well, since you're my little brother, i'll take you out for dinner, Mexican or ?

**jaros44sr** · 08-29-2019, 01:45 PM

my shop is empty, moved over to injection connection, sure feels like a load has been lifted from my shoulders. I'll let Dale handle my problems for now....

first problem he saw was the sealing of the pump to tank, he offered suggestions. I'll post up when I get more info.

Yes, that is one of the shelving units loaded with Jimmy parts, I'll sell them off as I don't use them

[url=https://flic.kr/p/2gEFFfj]20190722_194138[

one eye instead of four

[url=https://flic.kr/p/2h7pLiM]20190829_100502

[url=https://flic.kr/p/2h7pLo6]20190829_100619[

**richard2717** · 08-29-2019, 01:52 PM

Glad to see you making some progress on this Jim. Looks real nice out in the open shop like that.

**jaros44sr** · 08-29-2019, 02:06 PM

Quote:

Originally Posted by richard2717

Glad to see you making some progress on this Jim. Looks real nice out in the open shop like that.

Thanks Richard, I am breathing a sigh of relief, like the world is lifted. Thank goodness I saved some cash after I paid off the camaro and bought a boat. DON'T tell the wifey, I don't think she ever reads this site

Computers are installed using my mount, wiring is installed at main harness and working on fuel tank seal

Dale is a wiz at this early TPI set up, He was just out at the salt flats tuning cars

**1rippen6** · 08-29-2019, 06:03 PM

I see a grand national in your picture, does he work on them also?

litebulblsc · 08-29-2019, 08:26 PM

Quote:

Originally Posted by jaros44sr

Thanks Richard, I am breathing a sigh of relief, like the world is lifted. Thank goodness I saved some cash after I paid off the camaro and bought a boat. DON'T tell the wifey, I don't think she ever reads this site

Computers are installed using my mount, wiring is installed at main harness and working on fuel tank seal

Dale is a wiz at this early TPI set up, He was just out at the salt flats tuning cars

Hopefully it is a quick turn around.

**zicc1835** · 08-29-2019, 10:39 PM

great news moving the project along Jim, shop looks lonely ...

**jaros44sr** · 08-30-2019, 06:46 AM

Quote:

Originally Posted by 1rippen6

I see a grand national in your picture, does he work on them also?

actually, I think I saw 2-3, this guy works on anything, and does outstanding work

Quote:

Originally Posted by litebulblsc

Hopefully it is a quick turn around.

4-8 weeks is what he quoted me, but at this time it doesn't matter as she is getting worked on. Thanks for following

Quote:

Originally Posted by zicc1835

great news moving the project along Jim, shop looks lonely ...

Thanks Jesse, just bought an old boston whaler, so I have another project waiting to go in the shop, wish I had a bigger shop

sweet '55 you have been working on, glad the gas tank swap went well

**DeadheadNM** · 08-30-2019, 09:20 AM

Great progress Jim - ready to drive before the snow flies maybe?

**jaros44sr** · 09-01-2019, 08:48 AM

Quote:

Originally Posted by DeadheadNM

Great progress Jim - ready to drive before the snow flies maybe?

Thanks Pete, yeah, maybe, but I wouldn't mind driving in a lot of snow. our car washes down here have a product called salt x, and undercarriage wash.

Your trucks look fantastic, glad they made the move well, hope you enjoy the cold and snowy cold north

**DeadheadNM** · 09-01-2019, 10:41 AM

When I lived in MT I’d drive my k20 in salt free snow and had a good time. Too much salt here to consider it. I’m told that some car washes here recycle the undercarriage wash and it can be like brine - I’ve identified a car wash that doesn’t recycle water.

Thanks for the good words. Having a great time here!

**jaros44sr** · 09-01-2019, 05:59 PM

Quote:

Originally Posted by DeadheadNM

When I lived in MT I’d drive my k20 in salt free snow and had a good time. Too much salt here to consider it. I’m told that some car washes here recycle the undercarriage wash and it can be like brine - I’ve identified a car wash that doesn’t recycle water.

Thanks for the good words. Having a great time here!

didn't know that about recycled water, but I'm sure if I get the truck done I won't care what the weather is, 20 years is along time to wait, and I'm super excited to drive this thing....

Thanks for entertaining me with you're great builds and info. of said builds. I always key into a thread when i see you post up

06-29-2019, 08:46 AM	#3076
zicc1835 Senior Member Join Date: Mar 2011 Location: Hanover NJ Posts: 4,299	Re: PO has me PO'd ahh DUNCAN YoYo been there done that wish I had saved one I too shall be a spring chicken August 17th turning 68 years young...Happy Birthday Jim Jess __________________ Grand Theft Auto https://67-72chevytrucks.com/vboard/...d.php?t=855961 Doc & Kim build http://67-72chevytrucks.com/vboard/s...d.php?t=722288 I am from the desert http://67-72chevytrucks.com/vboard/s...d.php?t=650332 basket case build SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=648557

07-04-2019, 06:43 AM	#3078
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,764	Re: PO has me PO'd tank is mounted in truck, filler neck hose installed. What a pita putting tank up even with a trans jack seems the repop manufactorer coundn't measure, as the mounting holes for the "U" bracket were off by a 1/4", didn't have a tool to do the job quickly so I just grabbed a rat tail file, and made a bunch of noise Later will install rubber, between tank and straps. also, received a filler neck clamp from Eric(1972 jimmy). Didn't even know they had a clamp __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

07-05-2019, 08:01 AM	#3079
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,764	Re: PO has me PO'd [url=https://flic.kr/p/2gr67p1]20190704_123833 [url=https://flic.kr/p/2gr6dyW]20190704_123548 __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

07-05-2019, 08:07 AM	#3080
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,764	Re: PO has me PO'd finally was able to use my wobbler/center finder I bought several months ago [url=https://flic.kr/p/2gpEbJe]20190702_135842 __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

07-05-2019, 11:48 AM	#3081
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,764	Re: PO has me PO'd Poser [url=https://flic.kr/p/2grJWWm]20190705_113337 __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

07-06-2019, 10:52 AM	#3082
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,764	Re: PO has me PO'd oil pan is up,but not without a struggle. My all thread didn't work as planned, the back corners hit the all thread, but the front was ok. I've bought 2 of these gaskets and neither on came with those 4 gizmos that help with installation I have to open up the holes in the clamps for 1/4-20 studs. I have a press / punch with dies, want to see if it works on SS, I have to find the pliers that close these clamps [url=https://flic.kr/p/2gspivY]20190706_101712 [url=https://flic.kr/p/2gsp2LF]20190706_101726 [url=https://flic.kr/p/2gsp48J]20190706_101800 __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 07-06-2019 at 10:59 AM.

07-06-2019, 11:38 AM	#3083
rsavage Registered User Join Date: Aug 2009 Location: Alden NY Posts: 2,705	Re: PO has me PO'd I always glue the gaskets, even the one piece, to the pan with black RTV and let it sit for a few hours or overnight. I put the pan bolts down through the holes to keep them aligned, and also use some blue tape. Gasket stays on the pan whether it is upside down when installing on an engine stand or when putting it on the engine when it is in the truck. It's looking good Jim. __________________ 1961 C1 Corvette 1959 El Camino 350 TPI, 9" 4 w disc 69 Blazer K5 - sold July '20 2021 Durango RT 5.7

07-06-2019, 02:18 PM	#3084
AJs72K5 Registered User Join Date: Nov 2007 Location: South Tx Posts: 1,083	Re: PO has me PO'd The one piece gaskets don't need any glue or RTV. Just make sure the block and all mating surfaces are clean and bone dry. Here's the Snap-ups you're talking about. Don't know how I put up a pan and gaskets before without them. Huge difference. https://www.summitracing.com/parts/fel-es72863 __________________ - AJ Gray Matter Build - 1972 K5 with some stuff

07-06-2019, 08:28 PM	#3086
rsavage Registered User Join Date: Aug 2009 Location: Alden NY Posts: 2,705	Re: PO has me PO'd By the way Jim, what is the capacity of that pan? __________________ 1961 C1 Corvette 1959 El Camino 350 TPI, 9" 4 w disc 69 Blazer K5 - sold July '20 2021 Durango RT 5.7

07-07-2019, 07:42 AM	#3087
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,764	Re: PO has me PO'd thanks for your ideas guys, but I sorta went with both, just RTV'D the 4 corners where it made a sharp bend. ran my primer device yesterday and no leaks so far. But, who knows what will happen when the engine gets up to temp. and full pressure. the pan is a 8 quart, just a heads up, they didn't deburr inside where it was cut and welded so be careful when you wipe it down [url=https://flic.kr/p/2grFkpA]20190705_095016 thanks for the link on the parts AJ. I just may buy them and keep in tool box __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

08-29-2019, 01:45 PM	#3090
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,764	Re: PO has me PO'd my shop is empty, moved over to injection connection, sure feels like a load has been lifted from my shoulders. I'll let Dale handle my problems for now.... first problem he saw was the sealing of the pump to tank, he offered suggestions. I'll post up when I get more info. Yes, that is one of the shelving units loaded with Jimmy parts, I'll sell them off as I don't use them [url=https://flic.kr/p/2gEFFfj]20190722_194138[ one eye instead of four [url=https://flic.kr/p/2h7pLiM]20190829_100502 [url=https://flic.kr/p/2h7pLo6]20190829_100619[ __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 08-29-2019 at 01:58 PM.

08-29-2019, 01:52 PM	#3091
richard2717 Equal opportunity joke ofender Join Date: Oct 2011 Location: Eastern Shore of MD Posts: 10,128	Re: PO has me PO'd Glad to see you making some progress on this Jim. Looks real nice out in the open shop like that. __________________ Members I have met. Dually Jams, OlBlue60, ScottH, Tommyboy24, Dujobo, Warbucket, 2003 Silverado, Notsolo, my90k5, 6t727t2, Special-K ,Jack_71C10, tabarcus,72blazer_mud_bogger,pwdcougar,RSavage,EricSean,1Rippen6,invicta455,tennaragtop71,arks, Kendal,Bennett68C10, Perpendicular, Chainsawman, McGeesCustomMinis,ShortbedClayton,longblue72,6768chevylover,Tim71,Travisarmenta,Ol' Drippy,fleetmitch,georgieb51,Dave,bcnya2,Dadsburb https://paypal.me/6772GMtruckparts Most women like the strong, silent type… Fortunately for me, my wife prefers the out-of-shape, mouthy type.

08-29-2019, 06:03 PM	#3093
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,799	Re: PO has me PO'd I see a grand national in your picture, does he work on them also?

08-29-2019, 10:39 PM	#3095
zicc1835 Senior Member Join Date: Mar 2011 Location: Hanover NJ Posts: 4,299	Re: PO has me PO'd great news moving the project along Jim, shop looks lonely ... __________________ Grand Theft Auto https://67-72chevytrucks.com/vboard/...d.php?t=855961 Doc & Kim build http://67-72chevytrucks.com/vboard/s...d.php?t=722288 I am from the desert http://67-72chevytrucks.com/vboard/s...d.php?t=650332 basket case build SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=648557

08-30-2019, 09:20 AM	#3097
DeadheadNM Carpe manana Join Date: Dec 2010 Location: Eau Claire, WI Posts: 12,447	Re: PO has me PO'd Great progress Jim - ready to drive before the snow flies maybe? __________________ 1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547 1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308 Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland



Register or Log In To remove these advertisements.

09-01-2019, 10:41 AM	#3099
DeadheadNM Carpe manana Join Date: Dec 2010 Location: Eau Claire, WI Posts: 12,447	Re: PO has me PO'd When I lived in MT I’d drive my k20 in salt free snow and had a good time. Too much salt here to consider it. I’m told that some car washes here recycle the undercarriage wash and it can be like brine - I’ve identified a car wash that doesn’t recycle water. Thanks for the good words. Having a great time here! __________________ 1972 K5 CST Highlander Blazer: http://67-72chevytrucks.com/vboard/s...d.php?t=708547 1972 K20 Cheyenne Super: http://67-72chevytrucks.com/vboard/s...d.php?t=528308 Members met: ORANGBLAZ, 2003 silverado, MikeCofield, BB72CHEVKT, Duncan&Son, Sameyrasmea72, THENEWMEXICAN, HotRod C/10, brianthelion02, Sport/Truck, ryanroo, michael bustamante, Dirt's72, Already Gone, WestButteTruck, 57taskforce, Moreyel, painterljp, AASmedic, SoCoC10, Lumaestas, carbuff382, Chevyland

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.