How about some pics of 73-91 crew cabs

[kylep]

Originally Posted by stewartcrew

New here, but here is mine...

A few weeks ago


and now..



17x10 wheels with 35's, 96 Tahoe front seats, and 350sbc for now(cummins future)

that is one good looking truck, think you can show some interior shots?

[stewartcrew]

Originally Posted by joe231

Nice truck!
Posted via Mobile Device

Thank you!

[stewartcrew]

Originally Posted by Dieselwrencher

X2 love the color and wheels man!

Thank you!

Originally Posted by v30crewcab

Theres a 2wd crewcab that color running around here near me. its bone stock down to the white rims and hubcaps, except it has a cowl hood.

I would love to get my hands on that 2wd..Would be the best of both world's...

Originally Posted by kylep

that is one good looking truck, think you can show some interior shots?

Thanks, this is the best I can do for interior shots right now. The center console is just sitting there as I plan on building a custom one that fits my needs. No carpet yet just some sound deading material..I had to lower the seats about 4 and a half inches..

[rs72z]

Nice truck. How did you lower the seats?

[stewartcrew]

Originally Posted by rs72z

Nice truck. How did you lower the seats?

The driver's side is power so the mounting brackets where very tall so I just cut out desired amount and rewelded them. Only tricky part was I had one mounting point drop down because the floor as we all know is not flat. On the passenger side the seat has two sliding mechanisms one slides the whole seat up and out of the way for passenger entrance to the back and the other is the front back adjustment. I simply drilled the rivets out and took out the whole sliding mechanism for the passenger entrance to the back one and then cut the feet off the front back one and rewelded in there desired location..All in all it was very simply just a little time consuming and a lot of measurements..

[The Liberace]

Originally Posted by 1774btcrew

Craig, PM me. Found 4 19.5 step van wheels here in town for you.

You should call me I found 4 80s BMX bikes!

[rambone86]

hey guys , I'm stuck on what transfercase to swap into my 90 crew. I have a 90 cummins with a 47rh transmission. what have you guys used for this swap?

[v30crewcab]

dodge 241, from a 89-93 will bolt to the trans, and have pass drop, as well as fixed yoke. thats what I ran in my crewcab when it was auto, before I went to the stickshift.

[puppy]

Update: Lots of new parts
Most noticably the wheel and tires
Rear axle with 4.56 gears, detroit locker, rear disk brakes, braided hoses with AN fittings, relocated shock mounts, welded tubes
Front axle with 4.56 gears, dropped pitman arm, dropped draglink, rebuilt steering gear box, borgeson steering u-joint, sway bar disconnects
Made a rear bumper and threw a winch on the front
New exhaust, ORD steer box brace, tuned up and ready to roll
Engine is next!

[thirdstreettito]

Sweet! Very nice!

[Leedogg]

Went to Tampa Fl and picked up this bed and 2 bench seats. Going to run this bed til dad gets around to stretching the fenders on my original bed.

Ready to roll out to a car show next weekend-

[Dieselwrencher]

Originally Posted by v30crewcab

dodge 241, from a 89-93 will bolt to the trans, and have pass drop, as well as fixed yoke. thats what I ran in my crewcab when it was auto, before I went to the stickshift.

You mean NP205? Dodge didn't go to the 241's until 94, and they are LH drop.

[Dieselwrencher]

Leedog, your truck looks cool! Man those tires look like wide bicycle tires on those wheels!

[v30crewcab]

Originally Posted by Dieselwrencher

You mean NP205? Dodge didn't go to the 241's until 94, and they are LH drop.

nope, they had 241's in at least the 92-93's, if not all the way from 89, in the gas 4x4's. the cummins got the 205's. but since hes running an auto, its got the same 23 spline as the gas engines. the 94 up are drivers drop, and the 89-93 are pass drop. I still have mine sitting somewhere in the shop if you want a pic of it.






and some current pics of my crewcab!

[Dieselwrencher]

Ok, you're right, in the gassers they did. Your truck is looking good! I like that much better!

[v30crewcab]

Thanks, its SLOWLY getting back together. I miss driving it real bad, but its getting alot of new stuff, and things fixed better so its going to be much better this time around.

[GMC5.9cummins]

[ first post but this is my truck 89 gmc with a 5.9 cummins

[joe231]

Originally Posted by puppy

Update: Lots of new parts
Most noticably the wheel and tires
Rear axle with 4.56 gears, detroit locker, rear disk brakes, braided hoses with AN fittings, relocated shock mounts, welded tubes
Front axle with 4.56 gears, dropped pitman arm, dropped draglink, rebuilt steering gear box, borgeson steering u-joint, sway bar disconnects
Made a rear bumper and threw a winch on the front
New exhaust, ORD steer box brace, tuned up and ready to roll
Engine is next!

Very nice!!

What lift and tire size?
Posted via Mobile Device

[Mattman2010]

Originally Posted by puppy

Update: Lots of new parts
Most noticably the wheel and tires
Rear axle with 4.56 gears, detroit locker, rear disk brakes, braided hoses with AN fittings, relocated shock mounts, welded tubes
Front axle with 4.56 gears, dropped pitman arm, dropped draglink, rebuilt steering gear box, borgeson steering u-joint, sway bar disconnects
Made a rear bumper and threw a winch on the front
New exhaust, ORD steer box brace, tuned up and ready to roll
Engine is next!

Just when I thought I was 100% sure I was going to go back to a dually on my crew cab and you post pictures of this. That is a BA truck puppy. I'm with joe lift/tire specs please! Maybe a truck like that as a dually with thr same black and white theme would be cool too..
Posted via Mobile Device

[Dieselwrencher]

Originally Posted by GMC5.9cummins

[ first post but this is my truck 89 gmc with a 5.9 cummins

Very nice GMC!

[Leedogg]

Originally Posted by Dieselwrencher

Leedog, your truck looks cool! Man those tires look like wide bicycle tires on those wheels!

Thanks man! they are 265/35's "extra Load". you can run up to 150PSI in those tires, crazy. i run 50. The inners are E Load 16's. Should be able to haul anything i want. Got the stuff for a 6/8 drop, just waiting on Dad to get time at the shop to fool with my bed. Next year- it is gonna get air ride.

[Leedogg]

Puppy- Truck looks awesom! Especially like the pic from the front. intimidating ride. The Bumpers with the fairleads are cool.

GMC5.9cummins- Truck is just full of bad ass. Why the light bar? wrecker?

[USSkoval]

Originally Posted by GMC5.9cummins

[ first post but this is my truck 89 gmc with a 5.9 cummins

Nice! Grip Spurs on it? Have any pics of your traction bar setup?

[rambone86]

damn! that's nice.

Originally Posted by GMC5.9cummins

[ first post but this is my truck 89 gmc with a 5.9 cummins

[85sierraclassic]

Originally Posted by USSkoval

Nice! Grip Spurs on it? Have any pics of your traction bar setup?

looks to me like 6" inch lift and 36" goodyear military tires