What did you do to your truck today? - Page 186 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Woogeroo · 02-10-2012, 02:11 PM

Oil / oil filter change and lubed the front end.

Then I proceeded to run out of grease in the grease tube without a spare tube.

whoops.

-W

towersddg9 · 02-11-2012, 11:45 PM

Finally got a set of headers that fit good, did not have to trim the frame. This was set 3 as the first set of Hedman's wouldnt work with the motor moved to the forward hole, I also tried some patriot shorties, those were close but hit the CPP mounts

jbgroby · 02-12-2012, 12:31 AM

Mounthed the front clip.

Turkey · 02-12-2012, 01:30 AM

cleaned up some areas and reinstalled my speakers 'cause I found my VH Diver Down cassette. Classic tunes for "parts" running this afternoon.

sigshooter · 02-12-2012, 01:49 AM

put the inline back in

E911manager · 02-12-2012, 11:39 PM

Not a da^^ thing.. It was to freakin cold...

shortbed70 · 02-13-2012, 12:50 AM

Froze my butt off in the shop but managed to finish mounting my alternator,new flexplate installed,and got the throttle linkage done and tight.
Posted via Mobile Device

shortbed70 · 02-13-2012, 12:51 AM

Did I mention freeze...
Posted via Mobile Device

meat-head · 02-17-2012, 11:12 AM

Installed a new retro radio and kick panels with speakers.

64c20crewcab · 02-17-2012, 11:20 AM

I did full rear brake job on my 64 C20 Crew Cab using 1980 K20 front rotors, calipers and lines. Did the swap in 06 and 1 caliper locked up last weekend so i swapped all out yesterday. The mounting brackets are for a 14bolt disc conversion and work on the Eaton H052 / H072. From Great Lakes Offroad...
Posted via Mobile Device

K98AL · 02-17-2012, 01:08 PM

Tell some details on those kick panels w/speakers! They look great - how do they sound?

As for me, I picked up a new bed and tailgate from Craigslist and pulled out my radiator and heater core. Taking them to the radiator shop....got most of the front end disassembled.

meat-head · 02-17-2012, 02:39 PM

Quote:

Originally Posted by K98AL

Tell some details on those kick panels w/speakers! They look great - how do they sound?

They sound ok. Just running deck power now so cant really say for sure until I get an amp. Also the speakers are pretty low, so its a good idea to also run a speaker or pair of speakers in the factory dash to balance the sound.

**joedoh** · 02-17-2012, 11:33 PM

tried to get an alignment and ran into low truck prejudice.

"wont work on that its lowered"

actually its channeled so its really only 2 inches or so lower than stock.

"nope"

so tomorrow I get to find a new alignment shop.

Twiztid_66c10 · 02-18-2012, 12:08 AM

just ordered my dom 2600's for the front. got my sectioned cross member paid for. Ordered a running 350 to replace my old 6 from a local wrecking yard they will deliver it thurs. also ordered my new wiring harness from speed way. so a pretty productive day!

62-One-Ton · 02-18-2012, 04:22 AM

I pulled my windsheild and started to "discover" where I need to do some body work.
Posted via Mobile Device

mustangchef · 02-18-2012, 09:31 AM

put in rosewood armrest/doorpulls, three point seat belts,spring loaded the glove box door

**chevy_man5** · 02-18-2012, 10:44 AM

Quote:

Originally Posted by mustangchef

put in rosewood armrest/doorpulls, three point seat belts,spring loaded the glove box door

Do you have pictures of the armrest/door pulls and the spring loaded glove box?

66-PMD-GMC · 02-18-2012, 10:54 AM

What I did yesterday was mock up a front end on my 71 frame that I am converting to take a 63-66 cab and front end.
Today, I am taking the front clip and cab back off, hopefully get the nose of the 63-66 frame horns grafted to to the 71 frame, pulling the suspension, again, and cleaning everything up to be ready for paint.

mrfixit4818 · 02-18-2012, 06:09 PM

Put on my new headlights w 5600k bulbs and wired up 2 relays!nice!!!!!!!

61_FL_Apache · 02-18-2012, 07:01 PM

Repaired the leaky float on the gas tank sending unit. I kept wondering why it would only hit a half tank when full.... now I know.

kenmel · 02-18-2012, 08:16 PM

l
m

Harney Boy · 02-18-2012, 08:29 PM

Pulled my Side Mount gas tank, It was in really bad shape, I kept getting rust in my Holley 750 double pumper, So time for a new Gas tank and Sending unit! Cheap on Ebaymotors.

Harney Boy · 02-18-2012, 08:30 PM

Same problem with mine!

X24 · 02-18-2012, 08:51 PM

Installed a new in dash speaker, seatbelts and replaced my fuel pump.
Posted via Mobile Device

niterider65 · 02-18-2012, 09:48 PM

cleaned up the mess in the shop and guess what theres truck parts on the shelves now . I can find stuff again!

02-10-2012, 02:11 PM	#4626
Woogeroo Registered User Join Date: Aug 2003 Location: tool box Posts: 3,115	Re: What did you do to your truck today? Oil / oil filter change and lubed the front end. Then I proceeded to run out of grease in the grease tube without a spare tube. whoops. -W

02-11-2012, 11:45 PM	#4627
towersddg9 Registered User Join Date: Dec 2010 Location: Texas Posts: 246	Re: What did you do to your truck today? Finally got a set of headers that fit good, did not have to trim the frame. This was set 3 as the first set of Hedman's wouldnt work with the motor moved to the forward hole, I also tried some patriot shorties, those were close but hit the CPP mounts Attached Images

02-12-2012, 12:31 AM	#4628
jbgroby Registered User Join Date: Nov 2008 Location: Lacombe, LA Posts: 2,772	Re: What did you do to your truck today? Mounthed the front clip. Attached Images __________________ http://s1299.photobucket.com/user/jb...23904108567829

02-12-2012, 01:30 AM	#4629
Turkey Registered User Join Date: Dec 2009 Location: Orlando, Florida Posts: 427	Re: What did you do to your truck today? cleaned up some areas and reinstalled my speakers 'cause I found my VH Diver Down cassette. Classic tunes for "parts" running this afternoon. __________________

02-12-2012, 01:49 AM	#4630
sigshooter Registered User Join Date: Aug 2011 Location: Tahlequah, Ok Posts: 1,235	Re: What did you do to your truck today? put the inline back in Attached Images __________________ 1965 long bed ( grandpas old truck ) 1964 long bed BBW Custom Cab 1966 Short stepside 1964 long bed 1965 long bed Custom Cab, factory air, V-8, powerglide

02-12-2012, 11:39 PM	#4631
E911manager Registered User Join Date: Oct 2011 Location: Blanchard Oklahoma Posts: 424	Re: What did you do to your truck today? Not a da^^ thing.. It was to freakin cold... __________________ My Build CAPRICKUP 1964 Chevy SWB on a 94 Caprice http://67-72chevytrucks.com/vboard/s...d.php?t=492640

02-13-2012, 12:50 AM	#4632
shortbed70 Registered User Join Date: Mar 2002 Location: Forney TX Posts: 4,512	Re: What did you do to your truck today? Froze my butt off in the shop but managed to finish mounting my alternator,new flexplate installed,and got the throttle linkage done and tight. Posted via Mobile Device __________________ Troy 1965 Chevy Bagged,361 sbc,voodoo cam,1.5 full roller rockers,patriot 185cc vortec heads 2.02-1.60,vortec weiand polished intake,demon carb my truckhttp://67-72chevytrucks.com/vboard/s...d.php?t=332884 Big Red Dog build http://67-72chevytrucks.com/vboard/s...d.php?t=572274

02-13-2012, 12:51 AM	#4633
shortbed70 Registered User Join Date: Mar 2002 Location: Forney TX Posts: 4,512	Re: What did you do to your truck today? Did I mention freeze... Posted via Mobile Device __________________ Troy 1965 Chevy Bagged,361 sbc,voodoo cam,1.5 full roller rockers,patriot 185cc vortec heads 2.02-1.60,vortec weiand polished intake,demon carb my truckhttp://67-72chevytrucks.com/vboard/s...d.php?t=332884 Big Red Dog build http://67-72chevytrucks.com/vboard/s...d.php?t=572274

02-17-2012, 11:12 AM	#4634
meat-head Registered User Join Date: Nov 2011 Location: gilroy california Posts: 18	Re: What did you do to your truck today? Installed a new retro radio and kick panels with speakers. Attached Images

02-17-2012, 11:20 AM	#4635
64c20crewcab Registered User Join Date: Jun 2008 Location: North SD County Posts: 631	Re: What did you do to your truck today? I did full rear brake job on my 64 C20 Crew Cab using 1980 K20 front rotors, calipers and lines. Did the swap in 06 and 1 caliper locked up last weekend so i swapped all out yesterday. The mounting brackets are for a 14bolt disc conversion and work on the Eaton H052 / H072. From Great Lakes Offroad... Posted via Mobile Device __________________ ..............................._________ ......___________//___[[___{\ _____ ...../__(_(O)_)___/____/____/_(O)_/ 1964 C20 Long Stepside 3 Door Crew Cab - Armbruster-Stageway Conversion Y2K INDN Chief "ONE OF A KIND, NOT ONE OF THE CROWD" Aug 2010 - Front end frame cleanup & engine swap done!!! June 2011 - Rear end bagged Sept 2011 - Rebuild motor top end Sept 2012 - Parked and slowly working on it. Aug 2013 - Front end bagged - finally! Aug 2014 - Stepside swap conversion done. Finally ready to start bodywork! Have a few KEWL ideas... Here is my build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=335427

02-17-2012, 01:08 PM	#4636
K98AL Registered User Join Date: Dec 2011 Location: Sapulpa, OK Posts: 187	Re: What did you do to your truck today? Tell some details on those kick panels w/speakers! They look great - how do they sound? As for me, I picked up a new bed and tailgate from Craigslist and pulled out my radiator and heater core. Taking them to the radiator shop....got most of the front end disassembled.

02-17-2012, 11:33 PM	#4638
joedoh Senior Member Join Date: May 2007 Location: Doodah Kansas Posts: 7,774	Re: What did you do to your truck today? tried to get an alignment and ran into low truck prejudice. "wont work on that its lowered" actually its channeled so its really only 2 inches or so lower than stock. "nope" so tomorrow I get to find a new alignment shop. __________________ the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393

02-18-2012, 12:08 AM	#4639
Twiztid_66c10 Registered User Join Date: Feb 2010 Location: The Dalles Oregon Posts: 191	Re: What did you do to your truck today? just ordered my dom 2600's for the front. got my sectioned cross member paid for. Ordered a running 350 to replace my old 6 from a local wrecking yard they will deliver it thurs. also ordered my new wiring harness from speed way. so a pretty productive day! __________________ 1966 C-10 long wide- currently with 2 3/4 sectioned crossmember, 3 inch cupped a arms with 2700 bags, 67 master cylinder, in the middle of a v8 swap, soon custom rear wishbone set up and bags 1942 chevy/divco ambulance 1937 chevy truck

02-18-2012, 04:22 AM	#4640
62-One-Ton Registered User Join Date: Feb 2012 Location: Rescue, CA Posts: 255	Re: What did you do to your truck today? I pulled my windsheild and started to "discover" where I need to do some body work. Posted via Mobile Device

02-18-2012, 09:31 AM	#4641
mustangchef Registered User Join Date: Jan 2012 Location: Stockbridge,Mich Posts: 90	Re: What did you do to your truck today? put in rosewood armrest/doorpulls, three point seat belts,spring loaded the glove box door __________________ Don't stop, its harder to hit a moving target.



Register or Log In To remove these advertisements.

02-18-2012, 10:54 AM	#4643
66-PMD-GMC The 60-66 GMC/Pontiac guy.... Join Date: Oct 2010 Location: Apache Junction, Arizona Posts: 1,306	Re: What did you do to your truck today? What I did yesterday was mock up a front end on my 71 frame that I am converting to take a 63-66 cab and front end. Today, I am taking the front clip and cab back off, hopefully get the nose of the 63-66 frame horns grafted to to the 71 frame, pulling the suspension, again, and cleaning everything up to be ready for paint. Attached Images __________________ Building Genuine Pontiac Firepowered cars and trucks for several decades. Why Pontiac?? That's just me daring to be different. Projects.. 63 C10 Short Wheel Base fleetside (The Pro-Street) currently under reconstruction. 440CID 2X4 Pontiac

02-18-2012, 06:09 PM	#4644
mrfixit4818 Registered User Join Date: Oct 2011 Location: marietta Ga. Posts: 36	Re: What did you do to your truck today? Put on my new headlights w 5600k bulbs and wired up 2 relays!nice!!!!!!! Attached Images

02-18-2012, 07:01 PM	#4645
61_FL_Apache Who Me? Join Date: Sep 2010 Location: Royal Palm Beach, FL Posts: 4,067	Re: What did you do to your truck today? Repaired the leaky float on the gas tank sending unit. I kept wondering why it would only hit a half tank when full.... now I know. __________________ Steve 1997 Tahoe LT 4D 2WD (DD) 2001 Blazer 4D 2WD 1961 Apache 10 (sold) 1965 C10 Stepper (sold)

02-18-2012, 08:16 PM	#4646
kenmel Registered User Join Date: Oct 2011 Location: Sheridan, Arkansas Posts: 95	Re: What did you do to your truck today? l m

02-18-2012, 08:29 PM	#4647
Harney Boy Registered User Join Date: Oct 2010 Location: Geneva, FL Posts: 78	Re: What did you do to your truck today? Pulled my Side Mount gas tank, It was in really bad shape, I kept getting rust in my Holley 750 double pumper, So time for a new Gas tank and Sending unit! Cheap on Ebaymotors. __________________ 77' 3/4 Shortbed Stepside Silverado

02-18-2012, 08:30 PM	#4648
Harney Boy Registered User Join Date: Oct 2010 Location: Geneva, FL Posts: 78	Re: What did you do to your truck today? Same problem with mine! __________________ 77' 3/4 Shortbed Stepside Silverado

02-18-2012, 08:51 PM	#4649
X24 Registered User Join Date: Sep 2011 Location: CA Posts: 129	Re: What did you do to your truck today? Installed a new in dash speaker, seatbelts and replaced my fuel pump. Posted via Mobile Device __________________ X24 1964 chevy c10 step side 230ci straight six Auto power glide

02-18-2012, 09:48 PM	#4650
niterider65 Registered User Join Date: Jun 2011 Location: colleyville tx Posts: 624	Re: What did you do to your truck today? cleaned up the mess in the shop and guess what theres truck parts on the shelves now . I can find stuff again! Attached Images

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.