The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > LSx Swaps

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 12-14-2020, 05:08 PM   #101
biketopia
Senior Member
 
Join Date: Jul 2015
Location: Warrenton VA
Posts: 1,105
Re: Doing LS Swap - I have no idea what I'm doing!

Yup! are you setting in for good or are you pulling it back out? I'd get the old broken hardware out of the head before putting in chassis for the final time.
__________________
71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop.

07 Silverado Classic 2wd

95 Camaro 427SBC/TH350
biketopia is offline   Reply With Quote
Old 12-15-2020, 10:09 AM   #102
EagleChief
Registered User
 
EagleChief's Avatar
 
Join Date: Sep 2016
Location: Tulsa, OK
Posts: 420
Re: Doing LS Swap - I have no idea what I'm doing!

Quote:
Originally Posted by biketopia View Post
Yup! are you setting in for good or are you pulling it back out? I'd get the old broken hardware out of the head before putting in chassis for the final time.
Hopefully it is going in place and staying. I'd rather not pull the motor back out after I get it in there. But, maybe I need to?

What broken hardware are you talking about?
__________________
1971 C10 - Hugger Orange/White

My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=780197

LS Swap Thread: https://67-72chevytrucks.com/vboard/...d.php?t=811460
EagleChief is offline   Reply With Quote
Old 12-15-2020, 10:13 AM   #103
ls1nova71
Registered User
 
ls1nova71's Avatar
 
Join Date: Dec 2009
Location: Independence Mo
Posts: 4,118
Re: Doing LS Swap - I have no idea what I'm doing!

I think he's talking about the broken exhaust manifold bolts. Those are way easier to do outside the truck.
__________________
My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html

5.3 swap into my RUSTY '71 C10
http://ls1tech.com/forums/conversion...71-c-10-a.html
ls1nova71 is offline   Reply With Quote
Old 12-15-2020, 11:55 AM   #104
EagleChief
Registered User
 
EagleChief's Avatar
 
Join Date: Sep 2016
Location: Tulsa, OK
Posts: 420
Re: Doing LS Swap - I have no idea what I'm doing!

Quote:
Originally Posted by ls1nova71 View Post
I think he's talking about the broken exhaust manifold bolts. Those are way easier to do outside the truck.
Gotcha. I am planning to pull the exhaust manifolds,and the a/c, off before I put the motor in. After reading a lot of threads, neither one seem to fit as it is. So, for the time being, I'll go without a/c, and look for different option on the exhaust.
__________________
1971 C10 - Hugger Orange/White

My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=780197

LS Swap Thread: https://67-72chevytrucks.com/vboard/...d.php?t=811460
EagleChief is offline   Reply With Quote
Old 12-15-2020, 02:32 PM   #105
biketopia
Senior Member
 
Join Date: Jul 2015
Location: Warrenton VA
Posts: 1,105
Re: Doing LS Swap - I have no idea what I'm doing!

Yup, was referring to the broken manifold bolts still in the head, much easier to work on with it in front of you, not sprawled out in an engine bay. .
__________________
71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop.

07 Silverado Classic 2wd

95 Camaro 427SBC/TH350
biketopia is offline   Reply With Quote
Old 12-16-2020, 09:21 AM   #106
EagleChief
Registered User
 
EagleChief's Avatar
 
Join Date: Sep 2016
Location: Tulsa, OK
Posts: 420
Re: Doing LS Swap - I have no idea what I'm doing!

So, went to measure my frame rails last night. This never even registered that something was different. But, I realized that the frame rail has been "adjusted" to make some clearance. Don't know how they did this, or why, but maybe it'll give me some room to keep the a/c?
Attached Images
 
__________________
1971 C10 - Hugger Orange/White

My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=780197

LS Swap Thread: https://67-72chevytrucks.com/vboard/...d.php?t=811460
EagleChief is offline   Reply With Quote
Old 12-16-2020, 09:39 AM   #107
Thealien
Senior Member
 
Thealien's Avatar
 
Join Date: Jun 2007
Location: Pine Ridge Florida
Posts: 4,135
Re: Doing LS Swap - I have no idea what I'm doing!

Quote:
Originally Posted by EagleChief View Post
So, went to measure my frame rails last night. This never even registered that something was different. But, I realized that the frame rail has been "adjusted" to make some clearance. Don't know how they did this, or why, but maybe it'll give me some room to keep the a/c?
That bend in the frame is factory and if the engine is in just the right place. the AC compressor fits nicely there.
Thealien is offline   Reply With Quote
Old 12-16-2020, 11:10 AM   #108
ls1nova71
Registered User
 
ls1nova71's Avatar
 
Join Date: Dec 2009
Location: Independence Mo
Posts: 4,118
Re: Doing LS Swap - I have no idea what I'm doing!

Yep, I'm pretty sure that bend in the frame is for fuel pump access on original engines, they're all that way.
__________________
My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html

5.3 swap into my RUSTY '71 C10
http://ls1tech.com/forums/conversion...71-c-10-a.html
ls1nova71 is offline   Reply With Quote
Old 12-16-2020, 11:54 AM   #109
EagleChief
Registered User
 
EagleChief's Avatar
 
Join Date: Sep 2016
Location: Tulsa, OK
Posts: 420
Re: Doing LS Swap - I have no idea what I'm doing!

OK. Good to know. Thanks, guys.
__________________
1971 C10 - Hugger Orange/White

My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=780197

LS Swap Thread: https://67-72chevytrucks.com/vboard/...d.php?t=811460
EagleChief is offline   Reply With Quote
Old 12-22-2020, 12:02 PM   #110
EagleChief
Registered User
 
EagleChief's Avatar
 
Join Date: Sep 2016
Location: Tulsa, OK
Posts: 420
Re: Doing LS Swap - I have no idea what I'm doing!

Looking at this oil pan kit from Jegs: https://www.jegs.com/i/GM+Performanc...QAvD_BwE#qaTab

Anyone used it, or know for sure if it will fit in the trucks?
__________________
1971 C10 - Hugger Orange/White

My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=780197

LS Swap Thread: https://67-72chevytrucks.com/vboard/...d.php?t=811460
EagleChief is offline   Reply With Quote
Old 12-22-2020, 01:45 PM   #111
gmc684x4
Registered User
 
Join Date: Jul 2012
Location: Whitehorse yukon
Posts: 1,218
Re: Doing LS Swap - I have no idea what I'm doing!

I would set my engine in place first and see how low the truck pan hangs down then look at pan dimensions to see what will fit better

Placement how far forword or back and how high the engine sits will all play a large factor on which pan you will need

Give two strangers the same c10 and the same ls motor chances are both trucks will have different placement of the engines needing different clearances for the oil pan

Last edited by gmc684x4; 12-22-2020 at 01:50 PM.
gmc684x4 is offline   Reply With Quote
Old 12-22-2020, 02:09 PM   #112
EagleChief
Registered User
 
EagleChief's Avatar
 
Join Date: Sep 2016
Location: Tulsa, OK
Posts: 420
Re: Doing LS Swap - I have no idea what I'm doing!

Well, by my estimates (took some rough measurements last night), the current pan drops below the crossmember about 2.5"-3". Now, a normal truck height, that might be ok. But, my truck is lowered 3.5" in front, 5" in the rear.

I don't really want to put the motor in to see if it will work, then have to take it back out and order new parts. I want to have it ready to go, install the motor, and be done with it. I'm borrowing an engine hoist that I need to get back to it's owner, and have to have help and/or guidance putting the motor in.
__________________
1971 C10 - Hugger Orange/White

My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=780197

LS Swap Thread: https://67-72chevytrucks.com/vboard/...d.php?t=811460
EagleChief is offline   Reply With Quote
Old 12-22-2020, 03:53 PM   #113
99_Sierra
Registered User
 
99_Sierra's Avatar
 
Join Date: Jul 2012
Location: tulsa oklahoma
Posts: 53
Re: Doing LS Swap - I have no idea what I'm doing!

Quote:
Originally Posted by jjzepplin View Post
I just bought a 6.0L LQ9 for $375. I cringe when I have to spend that much on a fuel pump or tank. There has to be a cheaper way. I am leaning into using a stock fuel pump but retro fitting into my existing tank.

Here are snapshots from a post I read on facebook. I think I am going to go this route on my swap.
Attached Images
   
99_Sierra is offline   Reply With Quote
Old 12-22-2020, 07:41 PM   #114
ls1nova71
Registered User
 
ls1nova71's Avatar
 
Join Date: Dec 2009
Location: Independence Mo
Posts: 4,118
Re: Doing LS Swap - I have no idea what I'm doing!

Quote:
Originally Posted by EagleChief View Post
Looking at this oil pan kit from Jegs: https://www.jegs.com/i/GM+Performanc...QAvD_BwE#qaTab

Anyone used it, or know for sure if it will fit in the trucks?
I've used that pan in a couple of trucks. I make my own engine mounts, so take that into consideration, but it usually hangs down roughly 1/2" below the crossmember. That pan is about an inch to inch and a half or so shallower than the stock truck pan. You also won't be able to get both bottom bellhousing bolts to bolt into it, which is fine, so don't freak out about that.
__________________
My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html

5.3 swap into my RUSTY '71 C10
http://ls1tech.com/forums/conversion...71-c-10-a.html
ls1nova71 is offline   Reply With Quote
Old 12-22-2020, 07:42 PM   #115
ls1nova71
Registered User
 
ls1nova71's Avatar
 
Join Date: Dec 2009
Location: Independence Mo
Posts: 4,118
Re: Doing LS Swap - I have no idea what I'm doing!

Quote:
Originally Posted by 99_Sierra View Post
Here are snapshots from a post I read on facebook. I think I am going to go this route on my swap.
Had a friend do this years ago, the noise was terrible! You couldn't put enough insulation on the tank to not hear it even with the truck running. But if you are fine with that, it will work.
__________________
My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html

5.3 swap into my RUSTY '71 C10
http://ls1tech.com/forums/conversion...71-c-10-a.html
ls1nova71 is offline   Reply With Quote
Old 12-22-2020, 09:15 PM   #116
kev2809
low n' slo
 
kev2809's Avatar
 
Join Date: Mar 2009
Location: rosenberg, texas
Posts: 5,175
Re: Doing LS Swap - I have no idea what I'm doing!

from what ive been reading, the Cadillac cts-v pan is the best bet for lowered trucks. thats probably what i will end up using since mine has air suspension
__________________
67 1/2 ton Suburban - Project DRGNWGN. Build thread

-_--_--_ _________
_--_-_ -/____|__|__\__
,.,,,.,.,,.,|_O _______ O_]
kev2809 is offline   Reply With Quote
Old 12-22-2020, 11:10 PM   #117
gmc684x4
Registered User
 
Join Date: Jul 2012
Location: Whitehorse yukon
Posts: 1,218
Re: Doing LS Swap - I have no idea what I'm doing!

The other good pan is the holley pan or its fleabay knock off lots simaler to the fbody pan but the sump forward is shorter

The muscle car pan is deeper then the fbody pan

Personally I will set it in place and order from there or just go with the holley pan which is like the fbody pan 2.0
gmc684x4 is offline   Reply With Quote
Old 12-23-2020, 09:10 AM   #118
biketopia
Senior Member
 
Join Date: Jul 2015
Location: Warrenton VA
Posts: 1,105
Re: Doing LS Swap - I have no idea what I'm doing!

The f body or one of the holley (or copy) swap pans is your best bet for fitment. I don't know who said the CTS-V pan was best, it's almost an inch deeper than the F-body. I'm pretty sure I've posted this here before, but here is a great link with all the pan dimensions. https://www.improvedracing.com/gm-ls-oil-pan-dimensions
__________________
71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop.

07 Silverado Classic 2wd

95 Camaro 427SBC/TH350
biketopia is offline   Reply With Quote
Old 12-23-2020, 09:51 AM   #119
kev2809
low n' slo
 
kev2809's Avatar
 
Join Date: Mar 2009
Location: rosenberg, texas
Posts: 5,175
Re: Doing LS Swap - I have no idea what I'm doing!

Quote:
Originally Posted by biketopia View Post
The f body or one of the holley (or copy) swap pans is your best bet for fitment. I don't know who said the CTS-V pan was best, it's almost an inch deeper than the F-body. I'm pretty sure I've posted this here before, but here is a great link with all the pan dimensions. https://www.improvedracing.com/gm-ls-oil-pan-dimensions
its not like im making it up. ive personally havent used it, but its all over the board as an option for lowered trucks.

http://67-72chevytrucks.com/vboard/s...hlight=ctv+pan
__________________
67 1/2 ton Suburban - Project DRGNWGN. Build thread

-_--_--_ _________
_--_-_ -/____|__|__\__
,.,,,.,.,,.,|_O _______ O_]
kev2809 is offline   Reply With Quote
Old 12-23-2020, 10:28 AM   #120
ls1nova71
Registered User
 
ls1nova71's Avatar
 
Join Date: Dec 2009
Location: Independence Mo
Posts: 4,118
Re: Doing LS Swap - I have no idea what I'm doing!

The CTS-V pan is closer in physical shape to an old small block, thats why it fits well. The F body pan, while not deep, has a very long sump which requires the engine to be set back further.
__________________
My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html

5.3 swap into my RUSTY '71 C10
http://ls1tech.com/forums/conversion...71-c-10-a.html
ls1nova71 is offline   Reply With Quote
Old 12-23-2020, 10:48 AM   #121
biketopia
Senior Member
 
Join Date: Jul 2015
Location: Warrenton VA
Posts: 1,105
Re: Doing LS Swap - I have no idea what I'm doing!

I stand corrected.
__________________
71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop.

07 Silverado Classic 2wd

95 Camaro 427SBC/TH350
biketopia is offline   Reply With Quote
Old 12-23-2020, 12:31 PM   #122
EagleChief
Registered User
 
EagleChief's Avatar
 
Join Date: Sep 2016
Location: Tulsa, OK
Posts: 420
Re: Doing LS Swap - I have no idea what I'm doing!

Quote:
Originally Posted by biketopia View Post
The f body or one of the holley (or copy) swap pans is your best bet for fitment. I don't know who said the CTS-V pan was best, it's almost an inch deeper than the F-body. I'm pretty sure I've posted this here before, but here is a great link with all the pan dimensions. https://www.improvedracing.com/gm-ls-oil-pan-dimensions
You have shared that link with me. It has given me a lot to think about. Size wise, it looks like the Holley kits are the way to go. Seems like they have the lowest profile out of those options.

I just didn't want to have to shell out any more money. But, I guess that would happen if I bought the wrong kit/setup, then had to change it out for another one due to it not fitting, or hanging down too low.
__________________
1971 C10 - Hugger Orange/White

My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=780197

LS Swap Thread: https://67-72chevytrucks.com/vboard/...d.php?t=811460
EagleChief is offline   Reply With Quote
Old 12-23-2020, 02:28 PM   #123
Joemomma1
Registered User
 
Joemomma1's Avatar
 
Join Date: Mar 2009
Location: CA
Posts: 814
Re: Doing LS Swap - I have no idea what I'm doing!

Is removing the front end an option? Otherwise I'd say plan on pulling multiple times for clearances. There are some patterns forming here that you should avoid. The truck pan will work, avoid buying parts ahead of time and you're going to spend more money than you wanted. That's just what it is. Set it in as is then identify what you'd like to adjust. GET IT IN AND GET IT RUNNING. This is a really simple swap for these trucks, don't go making it difficult.
Joemomma1 is offline   Reply With Quote
Old 12-23-2020, 03:41 PM   #124
kev2809
low n' slo
 
kev2809's Avatar
 
Join Date: Mar 2009
Location: rosenberg, texas
Posts: 5,175
Re: Doing LS Swap - I have no idea what I'm doing!

Quote:
Originally Posted by Joemomma1 View Post
Is removing the front end an option? Otherwise I'd say plan on pulling multiple times for clearances. There are some patterns forming here that you should avoid. The truck pan will work, avoid buying parts ahead of time and you're going to spend more money than you wanted. That's just what it is. Set it in as is then identify what you'd like to adjust. GET IT IN AND GET IT RUNNING. This is a really simple swap for these trucks, don't go making it difficult.
curious, what do u mean by the truck pan will work? as far as clearance?
__________________
67 1/2 ton Suburban - Project DRGNWGN. Build thread

-_--_--_ _________
_--_-_ -/____|__|__\__
,.,,,.,.,,.,|_O _______ O_]
kev2809 is offline   Reply With Quote
Old 12-23-2020, 04:14 PM   #125
biketopia
Senior Member
 
Join Date: Jul 2015
Location: Warrenton VA
Posts: 1,105
Re: Doing LS Swap - I have no idea what I'm doing!

Quote:
Originally Posted by kev2809 View Post
curious, what do u mean by the truck pan will work? as far as clearance?
Yup, after you corrected me on the CTS-V pan I looked at the measurements more than just depth, and the stock truck pan is shorter front to back in the sump area, which should allow it to work in most cases, it's just deep so it hangs low.
__________________
71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop.

07 Silverado Classic 2wd

95 Camaro 427SBC/TH350
biketopia is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:09 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com