|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
04-15-2005, 12:36 AM
|
#1 |
|
C10 Club Tennessee
Join Date: Mar 2003
Location: White House, TN 37188
Posts: 8,281
|
Where to cut front springs?
I borrowed this pic from RandyC10
Can anybody use photoshop or a paint program and tell me where to cut on these stock springs to get a 2 inch drop?
__________________
Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4 |
|
|
|
04-15-2005, 08:39 AM
|
#2 |
|
Registered User
Join Date: Jan 2002
Location: WATAUGA,TX
Posts: 675
|
You have to cut exactly 1 coil from the spring because it sits in a pocket in the upper mount. So cut it directly below where the spring starts. I know it doesn't look like it will be 2 inches but trust me it will be at least that when they are mounted with the front end weight on them. Dont even be tempted to cut 2 coils. You will be buying another set if you do. Sorry I didnt have a photo available.
__________________
72 2wd 307/AT/AC/TILT WHEEL 78 JIMMY HIGH SIERRA Last edited by 72BLAZERDUDE; 04-15-2005 at 08:40 AM. |
|
|
|
|
04-15-2005, 11:37 AM
|
#3 |
|
67-72 Addict!
Join Date: Feb 2002
Location: The TAX State!
Posts: 7,856
|
Do you cut the bottom or top?
__________________
Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads |
|
|
|
|
04-15-2005, 11:59 AM
|
#4 |
|
Epoxy Primer Friendly
Join Date: Feb 2004
Location: South of Houston TEXXXAS
Posts: 680
|
spring trimming
The bottom so it will sit flat, never the top! GOOD LUCK
|
|
|
|
|
04-15-2005, 02:05 PM
|
#5 |
|
Registered User
Join Date: Jan 2002
Location: WATAUGA,TX
Posts: 675
|
Should have said lower control arm.
 Must have been the muscle relaxers Forgot I had to turn the spring over to cut it.
__________________
72 2wd 307/AT/AC/TILT WHEEL 78 JIMMY HIGH SIERRA Last edited by 72BLAZERDUDE; 04-15-2005 at 02:33 PM. |
|
|
|
|
04-18-2005, 05:36 AM
|
#6 |
|
C10 Club Tennessee
Join Date: Mar 2003
Location: White House, TN 37188
Posts: 8,281
|
I've heard some people say that it gives 3-4 inches. I just want to make sure they are still usable after I cut them.
__________________
Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4 |
|
|
|
|
04-18-2005, 09:15 AM
|
#7 |
|
Registered User
Join Date: Jan 2002
Location: WATAUGA,TX
Posts: 675
|
This is a picture of my sons truck with 2 1/2 drop spindles and 1 coil cut out. I am guessing 4 to 5 inch drop total.
__________________
72 2wd 307/AT/AC/TILT WHEEL 78 JIMMY HIGH SIERRA Last edited by 72BLAZERDUDE; 04-18-2005 at 09:16 AM. |
|
|
|
|
04-18-2005, 01:42 PM
|
#8 |
|
C10 Club Tennessee
Join Date: Mar 2003
Location: White House, TN 37188
Posts: 8,281
|
Then 1 coil it is.
__________________
Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4 |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
My Project 69 SWB
Linear Mode
