The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-01-2007, 02:23 PM   #1
ol Curt
Junior Member
 
ol Curt's Avatar
 
Join Date: Dec 2006
Location: Newburgh, IN
Posts: 1,247
Drum Brake Question

For one of you guys out there that still has drum brakes and has put a set on recently, I have to ask if you found any tips or tricks that made it easier to get all the confounding springs back on? This truck has the self adjusters and I think four springs (not counting those for hold downs and such). I have been fiddling with one wheel for several hours!!
ol Curt is offline   Reply With Quote
Old 01-01-2007, 03:02 PM   #2
kwkenuf
Retrofit Management
 
kwkenuf's Avatar
 
Join Date: Apr 2006
Location: Las Vegas, NV
Posts: 73
Re: Drum Brake Question

A brake spring tool helps but is not necessary. I did my rears a couple of months ago, the first one took a while, the second went easier. I've got a couple of pics if you're interested. I've seen much better pics on this board though with new parts instead of old brake dust covered shots.
__________________
My retrofit fleet
-1966 Suburban 2002 Tahoe drivetrain, firewall, floor, chassis and interior in progress
-1965 C-10 shortbed stepside, 2003 5.3/4L60E conversion. Power steering, tilt wheel, power front disc brakes, 2.5/4 inch drop, relocated fuel tank and battery, 2002 Silverado buckets and console. Swap Pics
-1968 Camaro 95 LT1/4L60E lots o' mods Web Page
-1961 Corvette project Corvette Corrections frame, C-4 suspension and brakes, 02 LS1/T-56, Never ending body workPics
kwkenuf is offline   Reply With Quote
Old 01-01-2007, 03:42 PM   #3
ol Curt
Junior Member
 
ol Curt's Avatar
 
Join Date: Dec 2006
Location: Newburgh, IN
Posts: 1,247
Re: Drum Brake Question

Yes,

please send or post pics.

Thanks
ol Curt is offline   Reply With Quote
Old 01-01-2007, 03:54 PM   #4
Woogeroo
Registered User
 
Join Date: Aug 2003
Location: tool box
Posts: 3,115
Re: Drum Brake Question

Drum brake assembly
Assembly sequence for a "typical" GM drum brake
1966 GM half-ton pickup (Delco Shown, Bendix similar)

http://www.pbase.com/nufsed/drumbrake

----

That is showing part by part on the rear brakes, the main difference is the park brake lever.

----

pics of the front and rear drum brakes on my '65 c10 :

http://matraca.home.mindspring.com/i.../05302006.html

----

Another trick is to jack the other side of the truck up and pull the wheel and drum off and see how it is routed.

good luck,

-W
Woogeroo is offline   Reply With Quote
Old 01-01-2007, 04:00 PM   #5
ol Curt
Junior Member
 
ol Curt's Avatar
 
Join Date: Dec 2006
Location: Newburgh, IN
Posts: 1,247
Re: Drum Brake Question

Wow,

That's neat having the parts painted and such. It makes it easy to identify them. I have the other wheel off. It's making the springs all fit without it coming apart that is giving me fits. I just finished a big bowl of chili ( I do everything better on a full stomach) and looking at the service manual. I have an idea it is the sequence of things that makes a difference. Made a copy of the page and am back out tot he garage to try again. Thanks for the help. Wish me luck!
ol Curt is offline   Reply With Quote
Old 01-01-2007, 06:39 PM   #6
SkylineNXS
Registered User
 
SkylineNXS's Avatar
 
Join Date: Oct 2006
Location: Elgin, IL
Posts: 658
Re: Drum Brake Question

I had fun a few months ago rebuilding one side of my brakes. Like u said, it s teh sequence. You can get spring puller tools and such but i did it with my dad. I took some time, but so does a lot of things. Two people definantly makes it easier.

Brad
__________________
2000 GMC Sierra EXT Cab Short 4x4, finally mine...

1966 C10 SWB Fleet, 250 I6, three on the tree....

Previously Owned....
1987 Chevy R10 "Silverado" (at least the badges were) Short Step 350 700r4....

1972 Chevy LWB Fleet 350/350






EXTENDED CAB ALL THE WAY!

.._..~...-...._...____
.._..-...______|_|__\____
..-..~.|_(O)__|_|__|_(O)]
SkylineNXS is offline   Reply With Quote
Old 01-01-2007, 06:53 PM   #7
Fred T
Cantankerous Geezer
 
Fred T's Avatar
 
Join Date: Aug 2002
Location: Bel Aire, KS
Posts: 6,264
Re: Drum Brake Question

A good set of brake spring pliers is a big help. And there is a huge difference between the made in USA and the made in xxx pliers.
http://www.lislecorp.com/tool_detail.cfm?detail=19
__________________
Fred

There is no such thing as too much cam...just not enough engine.
Fred T is offline   Reply With Quote
Old 01-01-2007, 07:00 PM   #8
layinrocker65
Registered User
 
layinrocker65's Avatar
 
Join Date: Jun 2005
Location: California
Posts: 521
Re: Drum Brake Question

I have taken my brakes apart afew times and I just do one side at a time and look at the other side if I get suck. Used brake tools for the springs and that helped the most. Thats all I have to say
layinrocker65 is offline   Reply With Quote
Old 01-01-2007, 08:09 PM   #9
ol Curt
Junior Member
 
ol Curt's Avatar
 
Join Date: Dec 2006
Location: Newburgh, IN
Posts: 1,247
Re: Drum Brake Question

Thanks guys. I finally got the one side on, and the pics were a great help. I think the brake pliers would be a good addition. I'm looking into those.

Woog, as always, your links are top notch!

Bob
ol Curt is offline   Reply With Quote
Old 01-01-2007, 08:21 PM   #10
ol Curt
Junior Member
 
ol Curt's Avatar
 
Join Date: Dec 2006
Location: Newburgh, IN
Posts: 1,247
Re: Drum Brake Question

Fred!!
Just when I was starting to buy some parts for the truck, and you had to send that great link to Lisle Tools. Now I'll be spending some money on tools.
ol Curt is offline   Reply With Quote
Old 01-01-2007, 08:27 PM   #11
Woogeroo
Registered User
 
Join Date: Aug 2003
Location: tool box
Posts: 3,115
Re: Drum Brake Question

The spring holder tools are a must, they make things so much easier.

ol Curt - glad they were a help, I needed those painted pics when I reinstalled the ebrake system on my '65, they saved my bacon.

-W
Woogeroo is offline   Reply With Quote
Old 01-01-2007, 08:44 PM   #12
zenish
Registered User
 
Join Date: Aug 2003
Location: stallings,nc
Posts: 401
Re: Drum Brake Question

i also use vise grips,i use them to grab the end of the spring so i hook it.
__________________
1964 c10 short step
1962 econoline van
1989 rs camaro
2006 yamaha vino 125
1975 goldwing
zenish is offline   Reply With Quote
Old 01-01-2007, 09:23 PM   #13
poorboy
Senior Member
 
poorboy's Avatar
 
Join Date: Jun 2006
Location: Oregon City, Or
Posts: 758
Re: Drum Brake Question

You can't go wrong spending $$ on tools. It's nice to have the right tool for the job. It also makes it alot easier.
poorboy is offline   Reply With Quote
Old 01-04-2007, 03:15 PM   #14
marvxyz1
Registered User
 
marvxyz1's Avatar
 
Join Date: Oct 2005
Location: Pittsburgh, Pa
Posts: 106
Re: Drum Brake Question

Use a good pair of vice grips and a little bit of muscle. You can also use cvice grips to install the anchor springs, by openiong the grips about 3 eigth in. an holding the spring down and turning the pin from behind the backing plate.
marvxyz1 is offline   Reply With Quote
Old 01-04-2007, 03:40 PM   #15
SIR
SIR
 
SIR's Avatar
 
Join Date: Apr 2005
Location: grants pass oregon,usa
Posts: 658
Re: Drum Brake Question

....investing in a GOOD pair of SAFTY GLASSES is one of the first tools you should purchase...those springs will come at you FAST!....
__________________
66long low fleet http://community.webshots.com/user/LVNR66
SIR is offline   Reply With Quote
Old 01-04-2007, 05:24 PM   #16
slepysal
Registered User
 
slepysal's Avatar
 
Join Date: Oct 2006
Location: San Jose NOR*CAL
Posts: 3,080
Re: Drum Brake Question

A dust mask iis a good idea too.

Last edited by slepysal; 01-05-2007 at 10:31 AM.
slepysal is offline   Reply With Quote
Old 01-05-2007, 02:02 AM   #17
leftcoast66
Registered User
 
leftcoast66's Avatar
 
Join Date: Sep 2006
Location: Covington, WA
Posts: 770
Re: Drum Brake Question

Sometimes when even the spring tools are hard to get the springs on I'll try and pop the smaller springs into their position I use a flat screwdriver. It was an amazing help last week doin the brakes on my '66
leftcoast66 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:45 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com